www.CasablancaFanCo.com Table of Contents To register your fan, please visit: www.CasablancaFanCo.com/register What to Expect with Your Installation Save your receipt for proof of purchase. Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
www.CasablancaFanCo.com What to Expect with Your Installation 1.888.227.2178 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Assess location 1 Ceiling angles greater than 34° will require an Angled Mounting Kit.
www.CasablancaFanCo.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M6010-01 • 10/30/14 • © Casablanca Fan Company Screwdrivers 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Preparation www.CasablancaFanCo.com ! KEEP DISC D AR Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. 6 M6010-01 • 10/30/14 • © Casablanca Fan Company 1.888.227.
www.CasablancaFanCo.com Option 1 Downrod 1.888.227.
www.CasablancaFanCo.com KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.CasablancaFanCo.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M6010-01 • 10/30/14 • © Casablanca Fan Company 1.888.227.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. www.CasablancaFanCo.com 1.888.227.2178 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) www.CasablancaFanCo.com OM FR • Connect the white wire (grounded) from the ceiling to the white wire from the receiver (marked “neutral in” or “common in”). black (live in) Connect the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”). black (ungrounded) blue black Connect the blue wire from the receiver (marked ”light out”) to the blue wire from the fan.
Wall Control www.CasablancaFanCo.com Screw Cut-Out 1.888.227.2178 Drywall Drill Holes Before Drywall Anchors Template Painter’s Tape Cover Plate Template Template After 1. Tape the provided wall control template with painter’s tape at the desired installation area. 2. Drill holes inside the four corners of the template. Note: Make sure the wall control template is level before proceeding to the next step. 1.
www.CasablancaFanCo.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 13 M6010-01 • 10/30/14 • © Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com 1.888.227.2178 Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from the hardware bag for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached.
www.CasablancaFanCo.com Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.227.2178 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
www.CasablancaFanCo.com Light Kit Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Want to install your fan without a light kit? Go to www.CasablancaFanCo.com/FAQs and click “How do I install my fan without the light kit?” Lift the lower switch housing up until the holes line up with the screw holes in the upper switch housing. 1.888.227.2178 Insert the three switch housing screws found in the hardware bag.
www.CasablancaFanCo.com Light Kit (continued) 1.888.227.2178 Thumbscrew Shade CONGRA YOU’RETULATIONS! DONE! To install each shade, first loosen the thumbscrews. Raise the shade to the light fixture and tighten the thumbscrews securely. Install a bulb into each of the sockets. When necessary, replace with bulbs of the same type and wattage. Note: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output.
Operation www.CasablancaFanCo.com er w o nP Battery Battery Holder 1.888.227.2178 r Tu ON Battery Door Before operating the wall control, press on the battery door to eject it. Unscrew the battery holder. Insert the battery, found in the control hardware bag, with the positive (+) side facing downward. Reinstall the battery holder and reinsert the battery door into the wall control. The remote transmitter should already be paired to the receiver and ready to use.
Operation (continued) www.CasablancaFanCo.com Reverse Button Fan Speed (Low) Fan Speed (a) Lights Down Lights Up Reverse Fan Power • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 20 seconds and then begin to dim. After a total of 30 seconds, the lights will be completely off. (b) Battery Holder Quickly press the up or down arrow to turn the lights off and on. Hold the up or down arrow to raise or dim the light level.
Maintenance & Cleaning www.CasablancaFanCo.com 1.888.227.2178 er w o nP r Tu Light Pull Chain OFF Be sure to turn off power to the fan before performing any maintenance or relamping. The light pull chain controls the power to the light fixture: on and off. For questions regarding removing a light kit, call customer service 1-888-227-2178. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.CasablancaFanCo.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Press a fan speed button (1-4). • Check the wall control battery. • Make sure that you have paired the wall control. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.