S3 OWNERS MANUAL
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CONTROL FEATURES: VERSA•TOUCH OPERATION . . . . . .
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor.
S3™ INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. WORK BENCH SETUP Setup. Remove the bottom foam from the box and place the fan rightside up in the foam. This protects the lamp socket during assembly.
CEILING HARDWARE ADDITIONAL HARDWARE CROSSBAR MOUNTING BRACKET 2 1/4″ x 8-32 ROUND HEAD SCREWS (2) WIRE NUT (4) 1″ x 8-32 ROUND HEAD SCREWS (2) FLAT WASHER (2) GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired.
S3™ CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4″ long canopy screws and canopy lock washers. Tighten the screw firmly by hand only. CROSSBAR MOUNTING BRACKET Note: On sloped ceilings, align the canopy opening towards the top or room peak. CANOPY CANOPY LOCK WASHER CANOPY SCREW BLADE HARDWARE BLADE SCREW (3 PER BLADE) METAL WASHER (3 PER BLADE) BLADE (3) BLADE INSTALLATION Step 3.
HANGING THE FAN Step 4. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. BALL NOTE: The fan weight is 23 pounds. SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 5a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut.
S3™ INSTALL BULB AND GLASS Step 9. Screw the 100 Watt Halogen bulb into the socket. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to fail almost immediately. IMPORTANT! When installing the halogen bulb, carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket.
VERSA•TOUCH ♦ INSTALLATION R W-42 CONTROL HOLDER W-42 CONTROL DRYWALL ANCHOR 6-32 (2) 9V BATTERY WOOD SCREW 1” (2) SCREW 6-32 X 3/8” (2) SCREW 6-32 X 1” (2) VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATION CAUTION! Do not use with wall dimmer. STANDARD TOGGLE SWITCH INNER MOUNTING HOLES REMOVE TABS ROCKER TYPE LIGHT SWITCH OUTER MOUNTING HOLES SWITCH COVER PLATE SWITCH COVER PLATE CONTROL HOLDER Standard Light Switch Step 1. Remove the two screws holding the switch cover plate.
VERSA•TOUCH OPERATION Fan Control To start the fan. Press the selected speed button to run the fan at the desired speed. LO Low speed MED Medium speed HI High speed To turn off the fan. Press the FAN OFF button. Airflow Direction To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is on or off. The fan returns to its set speed after reversing. Light Control Turn the light on or off independently from the fan by pressing the LIGHT button.
TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents.
761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-CASA-1ST (227-2178) www.CasablancaFanCo.com ©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S.