Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.227.
www.CasablancaFanCo.com What to Expect with Your Installation 1.888.227.2178 Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Assess location 1 Ceiling angles greater than 34° will require an Angled Mounting Kit.
Tools Needed www.CasablancaFanCo.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M6006-01 • 02/12/16 • © Casablanca Fan Company Screwdrivers 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Ceiling Bracket (continued) Preparation www.CasablancaFanCo.com ! KEEP DISC D AR Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. 6 M6006-01 • 02/12/16 • © Casablanca Fan Company 1.888.227.
Option 1 Downrod www.CasablancaFanCo.com 1.888.227.
Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT www.CasablancaFanCo.com ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M6006-01 • 02/12/16 • © Casablanca Fan Company 1.888.227.
Wiring www.CasablancaFanCo.com O FR M CEILIN White (grounded) Using orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan. T White CEIL KE M Black Using an orange wire connector from the hardware bag, connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M6006-01 • 02/12/16 • © Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from the hardware bag for this step. Insert blade screws and washers found in the hardware bag into the holes in the blades, then secure each blade to a blade iron. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 12 M6006-01 • 02/12/16 • © Casablanca Fan Company 1.888.227.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the mounting plate. It does not matter which two screw holes you choose. www.CasablancaFanCo.com Feed the optional light kit wires through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.227.2178 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
Switch Housing (continued) www.CasablancaFanCo.com 1.888.227.2178 CONGRA T LATIONS ! YOU’REUD ONE! Lift the lower switch housing up until the holes line up with the screw holes in the upper switch housing. Install the three switch housing screws, found in the hardware bag. Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling.
Remote Control ON D ON ON ECE 1 ON ECE 1 2 3 2 3 SET 4 4 Set D ON Once the power is turned on, the remote must be paired within 60 seconds. Pairing is only required once after initial installation. Battery Door 1.888.227.2178 ON r Tu D r we o nP www.CasablancaFanCo.com ON ECE 1 2 3 SET 4 Battery Remove battery door. Change the dip switch settings if the frequency matches a previously installed remote transmitter.
Operation, Maintenance & Cleaning www.CasablancaFanCo.com 1.888.227.2178 LED Fan Speed Dial Off (High) (Low) Reverse Light (If light kit is installed) ON D ON ECE 1 2 + To select fan speed press one of the numbers on the Fan Speed Dial. To calibrate the fan speed, run the fan on “6” for 90 seconds after each AC power reset. The LED light flashes to indicate a signal has been sent to the fan. To reverse the air flow direction, press the Reverse button while fan is running.
Troubleshooting www.CasablancaFanCo.com 1.888.227.2178 Fan doesn’t work Excessive wobbling Noisy Operation Remote doesn’t work • Make sure the wall switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Install a fresh battery in the wall control. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Make sure you have paired the remote. • Press a fan speed button (1-6).
