Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Tools Needed Mounting Options 1.888.227.
What to Expect with Your Installation www.CasablancaFanCo.com 1.888.227.2178 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit.
Tools Needed Ladder Screwdrivers www.CasablancaFanCo.com Pliers 1.888.227.2178 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Option 1 Downrod www.CasablancaFanCo.com 1.888.227.
www.CasablancaFanCo.com Hanger Ball KEEP! ! KEEP Adapter Cover Slide the adapter cover onto the downrod until it rests against the hanger ball. Remove the pre-installed setscrew so that the downrod can be inserted. 7 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company Hand tighten the downrod (at least 4-5 full turns) until it stops. 1.888.227.
(not to scale) 8” 1.888.227.2178 & 3/8” www.CasablancaFanCo.com STRIP CUT Downrod (continued) The wires can be cut, but leave at least 8” extending from the top of the downrod. Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 8” Lower the adapter cover until it rests flush against the motor housing. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company 1.888.227.
Wiring: Single Switch www.CasablancaFanCo.com Dual Switch Instructions Have a single switch? Follow these steps: Grou White Gr ou ed und Ungro nd ing i pe Str Black Green/Yellow Stripe Blue Connect the black wire (ungrounded) from the ceiling to the black wire from the fan. nded ellow Green/Y Connect the white (grounded) wire from the ceiling to the white wire from the fan. 1.888.227.
Wiring: Dual Switch www.CasablancaFanCo.com 1.888.227.2178 Have dual switches? Follow these steps: Grounded ellow Green/Y Grounded White Gr ou Ungrounded (lig ht) Black ing rou nd ed Green/Yellow Stripe Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. Un g Connect the black wire (ungrounded) from the ceiling to the black wire from the fan.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 12 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade arm with screws found in the hardware bag. 13 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company 1.888.227.
Light Kit www.CasablancaFanCo.com Place the LED assembly over the trim ring. Align the screw holes in the LED assembly with the screw holes in the trim ring. Screw two light kit assembly screws, found in the hardware bag, through the LED assembly and into the trim ring. 14 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company 1.888.227.
Light Kit www.CasablancaFanCo.com Screw two switch housing assembly screws, found in the hardware bag, halfway into the mounting plate on the bottom of the motor housing. It does not matter which two screw holes you choose. Feed the two single-pin connectors through the center hole of the LED assembly, then wrap the keyhole slots around the screws and twist counterclockwise. 1.888.227.2178 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
Light Kit www.CasablancaFanCo.com Connect the single-pin connectors from the LED assembly to the connectors from the fan. Connect the white wires together. Connect the blue and black wires together. Tuck the excess wiring above the LED assembly. Raise cap to the LED assembly. Align the notches on the sides of the cap with the screw holes in the LED assembly. 16 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company 1.888.227.
Light Kit www.CasablancaFanCo.com 1.888.227.2178 WARNING GLASS FALL HAZARD To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured. Tab Notch CONGRA T YOU’REULATIONS! DONE! Install the two LED assembly screws which can be found in the hardware bag. Position the notches in the outer rim of the globe so they line up with the three tabs on the inside rim of the housing.
Wall Control For Single Switch www.CasablancaFanCo.com If you have a dual switch setup, go to page 18 for dual switch installation instructions. 3 Installing the Wall Plate Bracket 4 Wiring the Wall Control Snap the Wall Control into the Wall Plate Bracket. off the power 1 Turning Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. n Tur the battery 2 Installing To access the battery compartment, er Pow OFF 1.
Wall Control For Single Switch 5 6 www.CasablancaFanCo.com 7 Installing the Wall Control Install the longer screws through the slots in the wall control into the switch box screw holes. Turn on the power. IMPORTANT n Tur 8 Installing the Wall Plate Push the wall plate onto the Wall Plate Bracket. It should snap into place. 1.888.227.
Wall Control For Dual Switches www.CasablancaFanCo.com 2 To install the Casablanca Wall Control into a dual switch location, you will need a wall plate with both a standard switch and rocker switch cut-out (sold separately). If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician. (Sold Separately) 1 Installing the battery To access the battery compartment, slide the battery door up. Battery Door Replace the used battery with two AAA batteries when needed. 1.888.
Wall Control For Dual Switches 4 Remove the existing wall plate 5 Remove the Casablanca Wall Control frame. www.CasablancaFanCo.com 7 Remove the existing wall plate. Save the screws. You will need them for the existing, marked light switch. 6 8 Wiring the Casablanca Wall Control 1. 2. 3. 4. Install the Wall Plate Install the wall plate that fits your setup (sold separately). 1. Use the screws you saved to reinstall into the light switch. 2. Remove the frame from the Casablanca Wall Control.
Wall Control www.CasablancaFanCo.
Maintenance & Cleaning www.CasablancaFanCo.com er w o nP r Tu OFF Be sure to turn off power to the fan before performing any maintenance. Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 23 M8550-01 • 07/19/18 • © 2018 Casablanca Fan Company 1.888.227.
Troubleshooting www.CasablancaFanCo.com 1.888.227.2178 Fan doesn’t work Excessive wobbling Remote does not work LED lights will not dim • Press a fan speed button (up or down arrow. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Make sure the battery is installed correctly. • Use the provided balancing kit and instructions to balance the fan. • If the remote still does not work, you may need to pair your remote.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.