www.CasablancaFanCo.com Table of Contents Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
www.CasablancaFanCo.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring 1.888.227.2178 Assess location w.
www.CasablancaFanCo.com Tools Needed Ladder Power Drill (optional) Screwdrivers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M6017-01 • 04/11/13 • © Casablanca Fan Company 1.888.227.
www.CasablancaFanCo.com Ceiling Bracket 1.888.227.2178 Bumper er w o nP r Tu OFF Make sure all four bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box.
Ceiling Bracket (continued) Preparation www.CasablancaFanCo.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M6017-01 • 04/11/13 • © Casablanca Fan Company 1.888.227.
www.CasablancaFanCo.com Hanging the Fan Ground Wire Screw Hole While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Locking Screw Once the motor is in the ceiling bracket, use the two locking screws found in the hardware bag to secure the motor to the ceiling bracket. Note: Fan style may vary.
Wiring OM FR CEILIN www.CasablancaFanCo.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.CasablancaFanCo.com Motor Housing Notch Motor Housing Screw Indentation Screw Holes Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket. The motor housing is not secured until the next step is complete. Do not leave unattended. With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag.
Blades www.CasablancaFanCo.com Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. 1.888.227.2178 Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching.
www.CasablancaFanCo.com Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.227.2178 Insert the third screw, found in hardware bag, into place and then tighten all three screws.
www.CasablancaFanCo.com Light Kit Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Lift the lower switch housing up until the screw holes line up with the screw holes in the upper switch housing. Want to install your fan without a light kit? Go to www.CasablancaFanCo.com/FAQs and click “How do I install my fan without the light kit?” Insert three switch housing screws, found in the hardware bag.
www.CasablancaFanCo.com Light Kit (continued) Bowl Glass Holder Light Pull Chain Fan Pull Chain er w o nP r Tu ON Finial Cap Be sure to turn the power back on at the breaker and the switch before trying to operate fan. Finial Press the bowl and glass holder flush against the metal plate. Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the grommet hole in the side of the finial cap. 1.888.227.
Maintenance, Operation & Cleaning www.CasablancaFanCo.com 1.888.227.2178 Bowl er w o nP r Tu OFF Be sure to turn off the power to the fan before performing any maintenance or relamping. Glass Holder Finial Cap Reverse Switch Finial Changing the direction of air flow - Move the reverse switch to the opposite position. Changing the bulbs - Unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand.
www.CasablancaFanCo.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Use the provided balancing kit and instructions to balance the fan.