www.CasablancaFanCo.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed 1.888.227.
www.CasablancaFanCo.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.CasablancaFanCo.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M6004-01 • 08/13/12 • © Casablanca Fan Company Screwdrivers 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket Installation www.CasablancaFanCo.com 1.888.227.2178 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screw Use machine screw (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box.
Ceiling Bracket Installation (continued) Preparation www.CasablancaFanCo.com 1.888.227.2178 ! KEEP DISC D AR Time Saver Tip: Get a helper Remove the shipping blocks from the motor. Save the five screws. They will be needed for blade iron installation. 6 M6004-01 • 08/13/12 • © Casablanca Fan Company to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps.
www.CasablancaFanCo.com Option 1 Downrod 1.888.227.
www.CasablancaFanCo.com KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.CasablancaFanCo.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M6004-01 • 08/13/12 • © Casablanca Fan Company 1.888.227.
Wiring OM FR CEILIN www.CasablancaFanCo.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.CasablancaFanCo.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M6004-01 • 08/13/12 • © Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com 1.888.227.2178 Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from hardware bag for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached.
www.CasablancaFanCo.com Switch Housing Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.227.2178 Insert the third screw, found in the hardware bag, into place and then tighten all three (3) screws.
www.CasablancaFanCo.com Light Kit 1.888.227.2178 Socket Shade Socket Ring Socket Ring Tool Remove the socket rings from the sockets. Install the shades onto the sockets. Install the socket rings onto the sockets. Tighten them by turning clockwise with the socket ring glass tool. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. For questions regarding removing a light kit, call customer service 1-888-227-2178.
www.CasablancaFanCo.com Light Kit (continued) 1.888.227.2178 CONGRA YOU’RETULATIONS! DONE! Insert three (3) switch housing screws found in the hardware bag. Install the CFL bulbs into the sockets. When necessary, replace with bulbs of same wattage. Connect the pull chain pendants to the short chains coming from the switch housing. Make sure the lower switch housing is securely attached to the upper switch housing.
Maintenance & Cleaning www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu ON Reverse Switch The pull chain controls the fan: high, medium, low, extra low, and off. The light pull chain controls the power to the light fixture: on and off. To switch the direction of air flow, move the reverse switch to the opposite position. 16 M6004-01 • 08/13/12 • © Casablanca Fan Company For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.CasablancaFanCo.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely. 1.888.227.