Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Tools Needed Mounting Options 1.888.227.
What to Expect with Your Installation www.CasablancaFanCo.com 1.888.227.2178 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit.
www.CasablancaFanCo.com Tools Needed Pliers Ladder Screwdrivers 11/32” Wrench Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) 1.888.227.2178 If mounting to a support structure, you will also need these tools. 3 M6032-01 • 02/21/17 • © Casablanca Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com Mounting Isolator Tapered Mounting Holes Ceiling Plate Screws Ceiling Plate Ceiling Plate Gasket 1.888.227.2178 Post er w o nP r Tu OFF Flange Nuts Ceiling Plate Ceiling Bracket Remove all four mounting isolators. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
Ceiling Bracket (continued) www.CasablancaFanCo.com 1.888.227.2178 For angled ceilings, point opening toward peak. Use the wood screw to poke holes through the rubber gasket in order to install the ceiling bracket assembly to your support structure or ceiling fan-rated outlet box. Use wood screws (included) and washers when securing to support structure with approved electrical outlet box.
Ceiling Bracket (continued) Preparation www.CasablancaFanCo.com 1.888.227.2178 IMPORTANT ! KEEP DISC D AR Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws.
www.CasablancaFanCo.com Option 1 Downrod 1.888.227.
www.CasablancaFanCo.com KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 10 M6032-01 • 02/21/17 • © Casablanca Fan Company 1.888.227.
Wiring www.CasablancaFanCo.com 1.888.227.2178 gro Un Grounded White ou nd ing i pe Str Gr Blue Connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. ellow Green/Y Connect the white (grounded) wire from the ceiling to the white wire from the fan. un ded Grounded Black Green/Yellow Stripe Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Canopy www.CasablancaFanCo.com 1.888.227.2178 Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 12 M6032-01 • 02/21/17 • © Casablanca Fan Company Note: Fan style may vary.
Blades www.CasablancaFanCo.com 1.888.227.2178 Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from the hardware bag for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.CasablancaFanCo.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 14 M6032-01 • 02/21/17 • © Casablanca Fan Company 1.888.227.2178 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
Switch Housing (continued) Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. www.CasablancaFanCo.com Lift the lower switch housing up until the holes line up with the screw holes in the upper switch housing. Install the three switch housing screws, found in the hardware bag. 1.888.227.2178 Attach the pull chain pendant to the short chain coming from the switch housing.
Switch Housing (continued) Maintenance & Cleaning www.CasablancaFanCo.com 1.888.227.2178 er ow P n r Tu ON CONGRA T YOU’REULATIONS! DONE! Reverse switch The pull chain controls the fan: from high to off. To switch the direction of air flow, move the reverse switch to the opposite position. In warm weather, use downward air flow pattern. In cold weather, use upward air flow pattern.
Troubleshooting www.CasablancaFanCo.com Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. 1.888.227.2178 • Use the provided balancing kit and instructions to balance the fan. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.