Table of Contents www.CasablancaFanCo.com To register your fan, please visit: www.CasablancaFanCo.com/register What to Expect with Your Installation Save your receipt for proof of purchase. Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
www.CasablancaFanCo.com What to Expect with Your Installation 1.888.227.2178 Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring You may need a friend to help you. Assess location 1 Standard Downrod w.
Tools Needed www.CasablancaFanCo.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M8535-01 • 02/10/16 • © 2015 Casablanca Fan Company Screwdrivers 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.CasablancaFanCo.com 1.888.227.
Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT www.CasablancaFanCo.com ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. Slide the adapter cover onto the downrod, then hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN.
Downrod (continued) Lower the adapter cover until it rests flush against the motor housing. www.CasablancaFanCo.com Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M8535-01 • 02/10/16 • © 2015 Casablanca Fan Company 1.888.227.
Wiring www.CasablancaFanCo.com OM FR CEILIN White (grounded) Using orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan. T White CEIL KE M Black Using an orange wire connector from the hardware bag, connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 10 M8535-01 • 02/10/16 • © 2015 Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Attach each blade assembly to the motor housing as shown using two blade screws, found in the hardware bag. Securely tighten the screws after all three blades are attached. 11 M8535-01 • 02/10/16 • © 2015 Casablanca Fan Company 1.888.227.
Upper Switch Housing Screw two switch housing assembly screws, found in the hardware bag, halfway into the mounting plate on the bottom of the motor housing. It does not matter which two screw holes you choose. www.CasablancaFanCo.com Feed the two single-pin connectors through the center hole of the upper switch housing, then wrap the keyhole slots around the screws and twist counterclockwise. 1.888.227.
LED Assembly www.CasablancaFanCo.com 1.888.227.2178 Light Kit Assembly Screw Connect the single-pin connectors from the LED assembly to the connectors from the fan. Note: If you are installing the optional no-light cap, please skip this step and instead use the dummy connectors to cap the two wires coming from the fan. Screw two light kit assembly screws from the hardware bag halfway into the upper switch housing.
Glass Lens Cap Tab www.CasablancaFanCo.com 1.888.227.2178 Notch CONGRA T YOU’REULATIONS! DONE! Position the notches in the outer rim of the glass lens cap so they line up with the tabs on the inside of the rim on the LED assembly. Carefully lift the glass lens cap up inside the LED assembly as far as it will go, then rotate the cap counterclockwise until it is held tightly in place by the tabs. 14 M8535-01 • 02/10/16 • © 2015 Casablanca Fan Company See next page for fan operation instructions.
Operation www.CasablancaFanCo.com r Tu ON 2 3 4 D ON ON ECE 1 2 3 SET 4 Battery Remove the battery door. Change the DIP switch settings if the frequency matches a previously installed remote transmitter. Install an A23 or MN21 alkaline battery. D 1 Once the power is turned on, the remote must be paired within 60 seconds. Pairing is only required once after initial installation. ON ON ECE D Battery Door ON r we o nP 1.888.227.
Operation (continued) www.CasablancaFanCo.com 1.888.227.2178 LED Off (Low) Fan Speed Dial (High) Reverse Light ON D ON ECE 1 2 + To select a fan speed press one of the numbers on the Fan Speed Dial. To calibrate the fan speed, run the fan on “6” for 90 seconds after each AC power reset. The LED light flashes to indicate a signal has been sent to the fan. To reverse the air flow direction, press the Reverse button while the fan is running. Press the Light button to turn the lights off/on.
Optional No-Light Cap www.CasablancaFanCo.com 1.888.227.2178 er w o nP r Tu OFF Be sure to turn off power to the fan before installing the bottom cap. Carefully rotate the glass lens cap clockwise until it comes loose from the tabs and lower it from inside the LED assembly. Uninstall the six screws around the outside of the glass lens cap. Remove the glass lens and set it aside for safe-keeping. Install the optional no-light cap using the same six screws. Tighten all six screws securely.
Maintenance & Cleaning www.CasablancaFanCo.com er w o nP r Tu OFF Be sure to turn off power to the fan before performing any maintenance. Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 18 M8535-01 • 02/10/16 • © 2015 Casablanca Fan Company 1.888.227.
Troubleshooting www.CasablancaFanCo.com Fan doesn’t work Excessive wobbling Noisy Operation • Press a fan speed button (1-4). • Tighten all of the blade screws until they are snug. • Tighten the blade screws until they are snug. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Check the circuit breaker to ensure the power is turned on.