Table of Contents Tools Needed Ceiling Options Ceiling Bracket 30 inches 3 4 Wiring PA G E Downrod Ladder PA G E 2 Canopy 5 12 PA G E 7 feet PA G E We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. What to Expect with Your Installation 1.888.227.2178 PA G E Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years.
www.CasablancaFanCo.com What to Expect with Your Installation 1.888.227.2178 Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Assess location 1 Ceilings that are more than 34° will require an angled mounting kit.
Tools Needed www.CasablancaFanCo.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M8539-01 • 01/12/16 • © 2016 Casablanca Fan Company Screwdrivers 1.888.227.
34O CEILING Ceiling Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.CasablancaFanCo.com 1.888.227.
Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT www.CasablancaFanCo.com ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M8539-01 • 01/12/16 • © 2016 Casablanca Fan Company 1.888.227.
Wiring www.CasablancaFanCo.com Note: If using the optional Low Profile canopy, you may need to carefully tilt the fan assembly at an angle while connecting the wires. OM CEILING FR Be sure to tilt the fan AWAY from the opening in the ceiling bracket and ensure the fan does not fall. green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) www.CasablancaFanCo.com OM FR OM CEILING FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Insert the two canopy screws found in the hardware bag. Lift the canopy place so that the screw holes are aligned. 11 M8539-01 • 01/12/16 • © 2016 Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Note: Guide posts are present on the blade to help align the blade with the motor. Lightly attach the blades to the motor with screws found in the hardware bag, then securely tighten after all three screws are attached. 12 M8539-01 • 01/12/16 • © 2016 Casablanca Fan Company 1.888.227.
Switch Housing & Light Kit Screw two upper switch housing screws from the hardware bag halfway into the mounting plate on the bottom of the motor housing. It does not matter which two screw holes you choose. www.CasablancaFanCo.com Feed the wire plugs through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist clockwise. 1.888.227.2178 Insert the third upper switch housing screw, found in the hardware bag, into place and then tighten all three screws.
Switch Housing & Light Kit (continued) www.CasablancaFanCo.com 1.888.227.2178 Sticker Sticker Connect the white wire from the fan to the white wire from the light kit, then connect the black wire from the fan to the black wire from the light kit. Locate the red sticker on the upper switch housing. Screw two switch housing screws from the hardware bag halfway into the other two screw holes in the upper switch housing.
Switch Housing & Light Kit (continued) www.CasablancaFanCo.com Notch Insert the third upper switch housing screw, found in the hardware bag, into place and then tighten all three screws. Tab Position the notches in the outer rim of the globe or no-light cap so they line up with the tabs on the inside rim of the upper switch housing. Carefully lift the globe then rotate clockwise until it is held tightly in place by the tabs. 15 M8539-01 • 01/12/16 • © 2016 Casablanca Fan Company 1.888.227.
Remote Control Battery Door www.CasablancaFanCo.com er w o nP r Tu ON CONGRA T U YOU’RE LATIONS! DONE! Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. 1.888.227.2178 The remote transmitter is already paired to the receiver and ready to use.
Operation, Maintenance & Cleaning www.CasablancaFanCo.com 1.888.227.2178 Reverse Switch The Fan Off button found on the right side of the transmitter turns the fan off. Buttons 1 through 4 turn on the fan and control the speed. • (1) Extra Low • (2) Low • (3) Medium The up arrow and down arrow buttons control the lights on the fan. Quickly press and release the up or down arrow to turn the lights off and on. Hold the up or down arrow to raise or dim the light level.
Operation, Maintenance & Cleaning (continued) www.CasablancaFanCo.com 1.888.227.2178 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
Troubleshooting www.CasablancaFanCo.com Fan doesn’t work Excessive wobbling Remote does not work • Press a fan speed button (1-4). • Tighten all of the blade and blade iron screws until they are snug. • Make sure the battery is installed correctly. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the remote control battery is working. • Make sure the blades spin freely.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.
