Ceiling Fan Light Kit Low Profile Installation Manual Models 99258, 99259, 99260 Compatible with: 2xxxx Types A - Z 51000-58999 fan series 59500-59999 fan series Select Casablanca Fans MA038-01 • 04/27/15
1.888.830.1326 BEFORE YOU BEGIN Read entire installation instructions carefully before beginning installation and save these instructions. Switch Housing Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s switch housing. Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan. From there, you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan.
1.888.830.1326 WHICH ASSEMBLY METHOD WILL I USE? Choose one of the four images below that most closely resembles the switch housing on your fan; then follow the instructions under the image. Cap Screw Switch Housing Screw Switch Housing Cap If your fan’s switch housing cap resembles this one, remove the cap screws with a Phillips head screwdriver. Then follow the TYPE-A ASSEMBLY INSTRUCTIONS on pages 4-5.
1.888.830.1326 TYPE-A ASSEMBLY INSTRUCTIONS 1 2 Light Kit Screw Switch Housing Wire Connector If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness. Screw the two light kit screws halfway into the switch housing.
1.888.830.1326 TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Globe Finial Cap Socket Finial Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage. Installing the globe - Press the globe flush against the metal plate. Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the hole in the side of the cap.
1.888.830.1326 TYPE-B ASSEMBLY INSTRUCTIONS 1 2 Switch Housing Light Kit Screw Switch Housing Wire Connector Access Hole If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness.
1.888.830.1326 TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Fan Pull Chain Light Pull Chain Grommeted Hole Socket Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage. If necessary, attach the extension chain provided to the fan pull chain coming from the switch housing. Then feed the end of the extension chain through the grommeted hole in the light kit.
1.888.830.1326 TYPE-C ASSEMBLY INSTRUCTIONS 1 2 Washer and Nut Switch Housing Threaded Rod Wire Connector Feed the wires through the switch housing cap, washer, and nut. Then install the switch housing cap by twisting clockwise onto the threaded rod. Install the washer and nut onto threaded rod and tighten securely. If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided.
1.888.830.1326 TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Fan Pull Chain Light Pull Chain Grommeted Hole Socket Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage. If necessary, attach the extension chain provided to the fan pull chain coming from the switch housing. Then feed the end of the extension chain through the grommeted hole in the light kit.
1.888.830.1326 TROUBLESHOOTING Lights don’t come on. • Make sure that the bulbs are properly installed. • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Check the circuit breaker to ensure the power is turned on. • Check the pin connections in the light kit. • Refer to the fan manual for locating the fan’s wiring. Verify that the light and power wires are correctly connected to the ceiling and the light kit.