BEL AIR™ OWNER’S MANUAL
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INTELI•TOUCH OPERATION . . . . . . . . . . . . . . .
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7' above the floor.
BEL AIR™ INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. IMPORTANT! To avoid possible damage to the Halogen bulb holder the fan must be placed on the styrofoam packaging from the box.
BEL AIR™ CROSSBAR MOUNTING BRACKET INSTALLATION Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening.
BEL AIR™ INSTALLING THE FAN BODY TOP COVER IMPORTANT! To avoid possible damage to the Halogen bulb holder the fan must be placed on the styrofoam packaging from the box. After removing the top cover from the upper half of the styrofoam, take the packaging from the box and put it on the floor. Place the fan in the recessed circle that the top cover was in. TOP COVER RETAINING SCREWS Step 3. Locate the three tabs on the top of the fan motor assembly.
HANGING THE FAN Step 7. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. CANOPY ELECTRICAL CONNECTIONS Step 8. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut.
BEL AIR™ BLADE HOLDER HARDWARE BLADE SCREW (4 PER BLADE) FLAT WASHER (4 PER BLADE) CENTER STYLE BLADE HOLDER & BLADE Step 12. Blade Installation Attach the blades to the blade holders with four blade screws and four steel washers provided for each blade. Hand tighten securely. BLADE SCREW (4 PER BLADE) FLAT WASHER (4 PER BLADE) INSTALLING THE HALOGEN BULB Step 13. Screw the 100 Watt Halogen bulb into the socket.
R INTELI•TOUCH© INSTALLING THE W-32 WALL CONTROL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. 3. Do not use more than one fan per wall control. 2. Do not use any additional control with your Inteli-Touch 4.
R INTELI•TOUCH OPERATION ♦ POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level. INTELI•TOUCH OPERATION ♦ SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. To select the desired fan speed: 1.
R INTELI•TOUCH OPERATION ♦ LIGHT-MINDER® PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: 1. Turn the OFF for at least three seconds. 2. Turn the ON. 3. Immediately operate the buttons in the following sequence: + + + 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off.
R TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents.
COMFORT•TOUCH ♦ W-21 MOUNTING PARTS R WALL BRACKET ANCHOR (4) REMOTE CONTROL W-21 REMOTE CONTROL WALL BRACKET ‘AAA’ ALKALINE BATTERY (3) WALL BRACKET SCREW (4) COMFORT•TOUCH ♦ W-21 WALL BRACKET INSTALLATION Installation of Remote Control The wall mounting bracket for the remote control should be located in a position that is approximately eye level. Secure the wall mounting bracket with the 11/4" screws or anchors provided, making sure it is level with the floor.
COMFORT•TOUCH ♦ IMPORTANT OPERATING NOTES Turning On Your Fan The fan will not receive any signals for the first 20 seconds after power on. This allows the electronics to warm up and stabilize. Power Failure The remote control is not affected by household power failure as it is battery operated. Once power is restored to the fan it will receive an auto-update signal from the remote control within 30 minutes after power is restored. All previously set modes and functions will be restored to the fan.
Pressing the REVERSE button will change the direction of rotation. An audio tone signals the beginning of the reverse sequence and you will see the airflow direction arrow changing. The fan gradually slows to a stop, then reverses direction. REVERSE COMFORT•TOUCH ♦ AUTO-SPEED FEATURE In the Auto Speed mode, fan speed changes in response to changes in room temperature. Push the AUTO button to start. The words 'AUTO SPEED' show on the display. Set the fan speed to the speed at which you are most comfortable.
REMOTE CONTROL CHANNEL NUMBER Note: Always change the remote control channel first. The fan channel can only be changed by having the desired channel already set in the remote control. COMFORT•TOUCH ♦ DUAL REMOTE CONTROL - BASE A second remote control can be purchased from your dealer to provide dual remote control of one fan. Because the fan could be confused by two controllers signaling different information it is necessary to set a BASE control and an AUXILIARY control.
R TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents.
761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-227-2178 www.CasablancaFanCo.com ©COPYRIGHT 1999 CASABLANCA FAN COMPANY • U.S.