Owner`s manual

20
21
Direct - Touch
1 2
0
4 3
1 2
0
4 3
1. To control the fan and lights from two
locations (a three-way circuit), use two W-74
wall controls.
2. Remove the screws and switch plate from the
existing switch box and the screws holding
the switch in the switch box. Figure #5
3. Pull the existing switch from the switch box to
expose the wire connections.
4. Determine which wire is connected to the
common terminal from the power source
(120V AC) of the three-way switch. (The
terminal will be marked on switch).
5. Remove the wire from the common terminal
of the three-way switch. Connect this wire to
the remaining black/white striped wire on the
W-74 control. Secure this splice with a wire
nut. Figure 4
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
DUAL W74 INSTALLATION
BLACK
BLACK
RED
GREEN
120V AC
BLACK
BLACK WITH
WHITE STRIPE
W-74
RED
RED
RED
BLACK WITH
WHITE STRIPE
GREEN
W-74
BLACK
BLACK
BLACK
BLACK
BLACK
NETRAL
WHITE
GREEN
To control the fan and lights from two locations (a three-way
circuit), use two W-74 wall controls as shown in the wiring diagram
in Figure #4. Before installing the two switches into the wall, place
both switches side by side, then locate the 6 dip switches on the
side of the two switches as shown in Figure #3. Then make sure that
the dip switches are set to the same address on both switches as
shown in Figure #3. When setting these dip switches you are setting
the channel number that is required to control both your fan and
lights from both sides of the room. If you are installing other Direct-
Touch
TM
3 fans within your home you may need to reset the dip
switches on these other fans to a different channel before installing
your W-74 wall control into the wall. Please review the section on
channel changing within this part of the operation manual as shown
on page #20.
DIP SWITCHES
W-74
Wall Control
BLACK AND WHITE
STRIPED WIRE
2 RED WIRES
2 BLACK
WIRES
6. Remove the two remaining wires from the three-way
switch. Connect the black wire of these wires to a black
wire on the W-74 control. Secure the splice with a wire nut.
The remaining red wire is to be connected to the other red
wire on the
W-74. Secure the splice with a wire nut. Figure 5
7. Connect the green ground wire coming from the back of the
W-74 control to the ground wire in the switch box. Secure
the splice with a wire nut.
8. Check your work by using the wiring diagrams as shown in
Figures # 4 and #5 on this page.
9. Install the W-74 in the wall box with the two long screws
provided.
10. Install the wall plate with the two short color-matched
screws provided.
11. Installation of the second W-74 control is identical. Repeat
steps 1 through 7.
Figure 3
Figure 4
Figure 5
OPERATION POWER
The
1 2
0
4 3
power button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
The
1 2
0
4 3
power button must be left on to retain a previously set fan speed
or light level.
OPERATION SPEED CONTROL
There are ve individual speed settings for the fan. Each speed is
indicated by the number on the controller and an audible tone for
each speed.
To select the desired fan speed:
Press the number on the controller corresponding to the speed
desired. 4 is high, 3 medium, 2 low, 1 ultra-low, and 0 is off.
OPERATION REVERSING AIRFLOW
The direction of airow can be changed from downward to upward
or from upward to downward.
To reverse the airow:
1. Make sure the fan is on and blades are turning.
2. Press the
1 2
0
4 3
reverse button. You will hear a series of clicks
from the fan as it speeds up before coming to a stop and
changing direction.
To turn the lights off and on, press and release the
1 2
0
4 3
button for
less than one second.
To dim the light, Press and hold the
1 2
0
4 3
button for more than 1
second. The light will come on at the last brightness setting and
increase in brightness until full power is reached, then start dimming
until the lowest setting is reached. This cycle will repeat until you
release the light button.
OPERATION LIGHTS
1 2
0
4 3
1 2
0
4 3
1 2
0
4 3
Note: It is normal for the fan
to start in the "High" position
from "Off" before changing to
the selected speed.
Down Light
Note: The dimming feature
will only work as long as the
dimming feature remains
active. See "Operation CFL
mode".
W-74 OPERATION