Outdoor Furniture STOP IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues, etc.), PLEASE DO NOT RETURN TO THE RETAILER/STORE from where you purchased the product. Please send e-mail to Customer Service Account : CMS-SHIANCO@SHIANCO.COM.CN To expedite any future warranty claims, please retain the Instruction Sheet, WarrantyCard, and Receipt for future use.
Owner’s Manual Item #:HF31701-L SKU.:HNGYGO-JW00462001 DANGER FIRE OR EXPLOSION HAZARD If you smell gas: • Shut off gas to the appliance. • Extinguish any open flame. • If odor continues, leave the area immediately. • After leaving the area, call your gas supplier or fire department. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death. WARNING • The installation of this unit must adhere to local codes or Propane Storage and Handling Code, CSA B149.2. • THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• Combustible material should not be within 60 inches of the top of the unit, or within 48 inches around the entire unit. • Keep the appliance area clear and free fr vapors and liquids. • • Do not add water into the unit. • Do not operate unit if any part has been under water. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and any gas control that has been under water. • Do not disconnect any part while unit is in use.
SAFETY INFORMATION Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by Teamson design corp. Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance. NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools. Min. Clearance 48 in (121.9 cm) Min. Clearance 48 in (121.
ADITAMENTOS ITE 1 3 SPECIFICATION T ITE SPECIFICATION T 1 PC Body 1 PC Guard 1 PC 1 Thermocouple 1 PC 11 Ignition Pin 1 PC 1 v roc 2 Box e c Co ro e o 1 PC or ro 1 PC re 1 PC Corrugated Pipe 1 PC 1 Gas valve 1 PC 1 PVC Cover 1 PC Burner 1 PC 1 Battery（AAA） 1 PC Regulator 1 PC Before beginning assembly of this product be sure all parts are present. Compare parts with package contents list and hardware contents list.
Check that the control knob (10) for the gas supply system is turned to the “OFF” position before starting any assembly. 10 Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the preassembled regulator from the Body (1) to the cylinder valve by turning the regulator coupling nut clockwise. Make sure it is fastened securely and tighten connections by hand only.
ASSEMBLY INSTRUCTIONS Pour the box of lava rocks (13) into the firebowl (1). CAUTION To ensure proper function, the guard on this burner should be free of lava rocks at all times. OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections.
OPERATION To Light 1. Make sure the control knob (M) is in the “OFF” position. 2. Open the door (2) and slowly open the valve on the propane gas tank by turning the knob counterclockwise. 3. Close the door (2) on the body. 4. Push and hold in the electronic ignitor (11) to create sparks within the electrode, continue to hold. 5. Push in the control knob (10) and turn to the “HIGH” position. Keep holding down the control knob(10) to allow gas to fow for 15 seconds. 6.
TROUBLESHOOTING Problem Heating unit won’t light Cause Solution Igniter pin and burner are wet Dry off with a soft cloth Igniter battery is incorrectly inserted Check which direction the battery is inserted Igniter pin is broken Contact us. for a replacement part Electrode wire is loose or disconnected Reconnect wire to the igniter box located inside the table behind the igniter box Contact us.
