Use and Care Manual

Package list of One Functions shower (B-1)
WARNING: Choking hazard. Please keep all small parts and plastic bags
out of the reach of children.
Plumbers with license install this shower system only.
02
Package list of Two Functions shower (B-2)
WARNING: Choking hazard. Please keep all small parts and plastic bags
out of the reach of children.
Plumbers with license install this shower system only.
03
Package list of Three Functions shower (B-3)
WARNING: Choking hazard. Please keep all small parts and plastic bags
out of the reach of children.
Plumbers with license install this shower system only.
04
Step 1: The depth is for reference only
Design water pipe sict Recommend using copper drop ear pipe elbow(1/2”-14NPT)
05
Applicable to one、two and three functions shower faucet
(Shown AS Above)
B-1 B-2 B-3
06
Step 3.Tiles(If you tile too thick, there is no enough space to install plate,
and handle)。
Two Functions shower( B-2 )
Three Functions shower( B-3 )
07
Step 4. Install Shower Arm and Rain Shower Head
08
Step 5. Install Shower bracket(if have)。
Install hand-held shower and hose(if have)。
09
Step 6. Install the tub spout(if have)。
10
01 02 03 04
05 06 07 08
09 10 11 12
13
01 02 03 04
05 06 07 08
09 10 11 12
13
14
15
16
17 18
01 02 03 04
05 06 07 08
09 10 11 12
13
14 15 16
17 18 19 20
Hot water Cold water Hot water Cold water Hot water Cold water
10 11 12
4X 4X 4X
Step 2. Clean the insides of all water pipes and fittings of dirt and other impurities.
(Be suitable for Pex pipe,Copper pipe and PVC pipe)。 Check for leakage
and/or blockage on both hot and cold water supplies.(Shower valve must be
connected with hot and cold water pipe. If only connect one, there is no water comes out)
Pull forward Rotating R or L controls temp
Hot Cold
03
1X
02
03
09
04
One Functions shower (B-1)
03
02
09
04
14
06
07
05
08
15
16
18
17
CAUTAION!!!
1. Water lines must be completely flushed before use, to avoid debris clogs in your water system leading to reduction
of water flow and mal-functioning.
2. Warranty is void if water lines are not flushed prior to use and installation of the new faucet.
3. Use of abrasives of any strength may damage the finish of the faucet and void the product warranty.
4. Do not over tighten your faucet on the countertop during installation. The valve assembly i tested to meet the
standards set by ASME A112.18.1 sec 5.8 which is listed at 100 LBF However, over-tightened or over-torqued
nuts may lead to cracks on the valve and will eventually lead to leaking and water damage.
5. Before installation of the faucet to the desired fixture, you need to secure and anchor your console, sink, tub,
or vanity cabinet firmly to the wall and to the floor. To ensure your fixture or faucet mounting surface cannot be
moved, before installation of the faucet please test to see if the cabinet or vanity can be moved by hand or body
weight If the faucet mounting fixture is not secure and anchored, it will eventually crack the valve and cause leaking
leading to property damage. In order to avoid this, be sure to secure your installation surface. Do not use any Power
Tools for assembly and installation which can cause internal fractures to the fixture.
550mm
110mm
圆形花洒说明书正面 (尺寸：550x155mm)
扇形折，120g双胶纸; 单色K.
圆形花洒说明书背面 (尺寸：550x155mm)
扇形折，120g双胶纸; 单色K.
155mm155mm
Installation
Instruction (B)
[phone]
www.casainc.com
[e-mail]