Installation Guide

For Semi-Flush:
For Chandelier: (See Fig.3)
1. Unscrew the hex nut and washer to remove canopy(-a) from the
fixture. Then screw the hex nut and washer back to nipple(-b)
tightly. (See Fig.1 & Fig.2)
2. Take out the parts for Chandelier from the hardware package.
3. Attach nipple(-a) to the mounting strap, then secure it with a washer
and hex nut.
4. Attach the mounting strap to the outlet box by using two mounting
screws.
5. Thread the fixture wire and fixture grounding wire through the loop,
then secure the loop onto nipple(-b).
6. Choose the length of the chain you need, and weave the fixture wire
and the fixture grounding wire through the chain. Connect one
end of the chain with the loop by using the loop lock.
7. Secure the top loop to nipple(-a).
8. Thread the fixture wire and fixture grounding wire through the collar,
canopy, top loop, nipple(-a) and mounting strap.
9. Connect the other end of the chain with the top loop by using the
loop lock.
10. Follow step 5 for Semi-Flush.
11. Attach canopy(-b) to the mounting strap by inserting the top loop,
then secure it with the collar.
12. Follow steps 7~9 for Semi-Flush.
Fixture Wire
Chain
Mounting Screw
Nipple(-a)
Fixture Grounding Wire
Collar
Top Loop
Canopy(-b)
Fixture
Fixture
Mounting Strap
Green Grounding Screw
Hex Nut
Wire Nut
Washer
Outlet Box
House Grounding Wire
Loop
Nipple(-b)
Loop Lock
Loop Lock
Mounting Parts for Chandelier
Fig.3
1. Take out the parts for Semi-Flush from the hardware package.
2. Attach two screws to the mounting strap, then secure them with
two lock nuts. Adjust the length of the screws if necessary.
3. Attach the mounting strap to the outlet box by using two mounting
screws.
4. Remove the loop from the fixture wires.
5. Cut the redundant wires if necessary. Pull out the outlet wires and
house grounding wire from the outlet box. Make wire connections
using the wire nuts:
---Connect the smooth wire (marked) from the fixture to the black
wire from the power source.
---Connect the ridged wire (unmarked) from the fixture to the white
wire from the power source.
---Attach the fixture grounding wire to the mounting strap with the
green grounding screw. Then connect it to the house grounding
wire with a wire nut.
Carefully tuck the wires back into the outlet box.
6. Attach canopy(-a) to the mounting strap by inserting the screws,
then secure it with the bolt nuts.
7. Attach the candle tubes to the sockets, then install bulbs
(not included). See relamping label at socket area or packaging
for maximum allowed wattage.
8. Install crystal drops as shown in diagram.
Note: To replace broken crystal drops -Open the pins to remove
the crystal drops, hook the new crystal drops, and then close
back pins. Avoid bending the pins into sharp angle.
9. Turn on the power at the main fuse or circuit breaker box.
Lock Nut
Outlet Box
Wire Nut
Screw
Mounting Strap
Green Grounding Screw
House Grounding Wire
Fixture Grounding Wire
Mounting Screw
Fixture Wire
Canopy(-a)
Socket
Candle Tube
Crystal Drop
Bolt Nut
Canopy(-a)
Fig.1 Fig.2
Hex Nut
Washer
Hex Nut
Washer
Nipple(-b)
061219
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THIS INSTRUCTION.
MN-CHU014