Installation Guide

ManualsBrandsCascadia ManualsOutdoor Wall LightsATG9536670

T0039 --- Page 1 / 4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

T0039

Important to Know

1. Read all instructions carefully before installation

and operation.

2. If you are not familiar with state and local electrical

codes, it is recommended that you consult with a

qualified electrician.

3. Before installation, shut off power at the main fuse

or circuit breaker box. Be aware that simply turning

off the wall switch is not sufficient to prevent

an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power

source. Maximum wattage light bulb is 100W.

5. Do not attempt to take the lantern apart; there are

no serviceable parts inside.

6. To avoid sensor damage by lightning or electrical

surge, make sure the grounding wire is securely

connected.

7. For general safety and to avoid any possible

damage to the sensor, be sure the power is

switched "off" before replacing the bulb.

Features

Maximum Wattage: 100W

Work Temperature: -4

F ~ 104

1. Use the dim-to-bright illumination option

where you want some minimum illumination

throught out the night, such as at your front

entrance or garage door. Use the dark-to-bright

illumination option where you do not need

minimum brightness, such as the backyard or

back porch.

2. Your light comes with a 3-way 15-85-100W

bulb. Achieve true energy savings using dim

illumination using 3-way bulbs, instead of

energy-consuming dimmers. For best

performance, use the bulb included or other

incandescent or halogen 3-way bulbs. For

conventional motion sensor, without dim ambient

illumination, use regular incandescent or halogen

bulb.

120424

3-Way (15W-85W-100W)

standard base bulb

(Bulb included)

Ball Nuts

Frame

Set Screws

Glass Shade

Rubber Pads

Glass Shade

Clip

FIG.1

Mounting Screws

Headless Screws

Cross Bar

House Grounding Wire

Green Grounding Screw

Fixture Grounding Wire

Wire Nut

Outlet Box

Fixture Wire

Lock Nuts

Back Plate

Metal Ring

Frame

Fixture

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS T0039 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Important to Know Features 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation Steps 1. Shut off power at the circuit breaker of where the fixture is to be installed. 2. Thread two headless screws through the cross bar, then secure them with four lock nuts (two on each side of the cross bar). Adjust the length of the headless screws if necessary. 3. Attach the cross bar to the outlet box by using two mounting screws. 4. Unscrew the set screws to remove the metal ring from the frame. 5. Gently insert the glass shade into the frame in place, secure it by pressing the clips.
PAGE 3
. 6 MODE (nighttime operation only) - Function with 3-Way Bulb: The light will brighten to full power at dusk. The light will operate at a low level brightness after 6 hours. The light brightens to full power when motion is detected. When motion is no longer detected, the lights will remain on for the predetermined time you set (5~180 seconds). After that, the lights will dim to low level brightness. - Function with Regular Bulb: The light will brighten to full power at dusk.
PAGE 4
NOTE: 1. When power is first applied, the light will turn to full brightness Where you install your lantern is important: immediately. Wait for 60 seconds to allow the sensor to warm Be sure the light is mounted straight on the wall; up. otherwise, the detection distance may be limited. 2. The sensitivity of the motion sensor will increase as the 220° FIG.4 FIG.5 environmental temperature gets cooler. You may wish to 6.5' make adjustments when the season changes temperature.