Installation Guide

NOTE: Before installing, consult local electrical codes for wiring and grounding requirements.
CF38215 / CF38217
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
WARNING:
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
Installation Steps:
Fixture Wire
Chain
Mounting Screw
Nipple-1
Grounding Wire
Collar
Top Loop
Canopy
Mounting Strap
Green Grounding Screw
Hex Nut
Wire Nut
Washer
Ceiling Box
Nipple-2
Coupling
Hex Nut
Cap
Loop
Fixture
House Grounding Wire
Loop Lock
Loop Lock
1. Attach the nipple-1 to the mounting strap, and then secure
with a washer and a hex nut.
2. Attach the mounting strap to the ceiling box by using two
mounting screws.
3. Follow steps 3~4 as For Semi-Flush.
4. Thread the fixture wire and grounding wire through the hex
nut, nipple-2, cap and loop in order.
5. Screw the nipple-2 into the coupling, and then secure with
the hex nut.
6. Attath the cap onto the fixture by inserting nipple-2, and then
secure with the loop.
7. Choose a certain length of the chain you need, and then
weave the fixture wire and the grounding wire through the
chain links. Connect one end of the chain with the loop by
using the loop lock.
8. Secure the top loop to the nipple-1.
9. Thread the fixture wire and grounding wire through the collar,
top loop, canopy, nipple-1 and mounting strap in order.
10. Connect the other end of the chain with the top loop by using
the loop lock.
11. Follow step 5 as For Semi-Flush.
12. Attach the canopy to the mounting strap by inserting the
top loop, and secure with the collar.
13. Follow steps 7~10 as For Semi-Flush.
Mounting Parts For Pendant
Fig.1
For Pendant:(See Fig.1)
For Semi-Flush
Lock Nut
Ceiling Box
Wire Nut
Screw
Mounting Strap
Green Grounding Screw
House Grounding Wire
Grounding Wire
Mounting Screw
Fixture Wire
Canopy
Bolt Nut-1
Bolt Nut-2
Arm
1. Attach two screws to the mounting strap, and secure with
two lock nuts.(You can adjust the length of the screw
if necessary.)
2. Attach the mounting strap to the ceiling box by using two
mounting screws.
3. Adjust the arms of the fixture according to the drawing of
the package.
4. Screw the headless screws into the hole of the pan and
attach the fixture to the pan by inserting the headless
screws, and then secure with the bolt nuts-2.
5. Cut the redundant wires if necessary, and make wire
connections with wire nuts:
--- Connect the smooth wire (marked) from fixture to the
black wire from power source.
--- Connect the ridged wire(unmarked) from fixture to the
white wire from power source.
--- Attach the grounding wire and house grounding wire to
the mounting strap with a green grounding screw.
Carefully tuck wires back into the outlet box. 
6. Unscrew two bolt nuts-1 from the canopy, attach the canopy
to the mounting strap, and then secure with two bolt nuts-1.
7. Install bulbs. (Please do not exceed the maximum
capacity which is recommended on the package.)
8. Screw the nipple into the coupling, and then secure with
a washer and a hex nut.
9. Attach the glass shade upward to the fixture by inserting the
nipple, and then secure with the washer, hex nut and finial.
10.Turn on the power at fuse or circuit box.
Pan
Fixture
Washer
Socket
Coupling
Hex Nut
Nipple
Glass Shade
Finial
Washer
Hex Nut
Headless Screw