Installation Guide

ManualsBrandsCascadia ManualsChandeliersBozeman 6-Light Burnished Bronze Rustic Tinted Glass Shaded Incandescent Chandelier

1. Attach nipple(-a) to the mounting strap, then secure it with a washer and hex nut.

2. Attach the mounting strap to the outlet box by using two mounting screws.

3. Secure the top loop to nipple(-a).

4. Carefully attach the upper fixture onto the holder by securing the rod to nipple(-b).

5. Adjust the arms of the fixture according to the drawing of the package.

Important:

a. The arms should be positioned with equal distances between them.

b. The arms should be fixed securely.

6. Attach the silhouettes to the holder by aligning holes, and then secure them with

set screws. The silhouettes should be placed as shown in Fig.1 when look the

fixture from downward or upward.

a. Use the tree side of the silhouettes which marked "P-T" or "P-Y" or "P-H"

touch the holder.

b. You can install the silhouettes which marked P-Y (for CH55456) or marked

P-L (for CH55556) or marked P-H (for CH55756) to the location of silhouettes

which marked P-T (for CH55656) shown in right graph to replace them.

7. Choose the length of the chain you need, then weave the fixture wire

and the fixture grounding wire through the chain, collar and canopy.

8. Connect one end of the chain with the loop by using a loop lock.

9. Connect the other end of the chain with the top loop by using

another loop lock.

10. Thread the fixture wire and fixture grounding wire through

the top loop, nipple(-a) and mounting strap.

11. Pull out the outlet wires and house grounding wire from the

outlet box. Make wire connections using the wire nuts:

---The smooth wire (marked) from the fixture to the

black wire from the power source.

---The ridged wire (unmarked) from the fixture to the

white wire from the power source.

---Attach the fixture grounding wire to the mounting

strap with the green grounding screw. Then connect

it to the house grounding wire with a wire nut.

Carefully put the wires back into the outlet box.

12. Attach the canopy to the mounting strap by inserting the

top loop, then secure it with the collar.

13. Attach the glass shades to the glass holders, then secure

them with socket rings.

14. Install bulbs (not included). See relamping label at

socket area or packaging for maximum allowed wattage.

15. Turn on the power at the main fuse or circuit breaker

box.

Fixture Wire

Arm

Glass Shade

Glass Holder

Chain

Mounting Screw

Nipple(-a)

Fixture Grounding

Wire

Collar

Top Loop

Canopy

Mounting Strap

Green Grounding Screw

Hex Nut

Wire Nut

Washer

Outlet Box

House Grounding Wire

Loop Lock

Rod

Loop

Silhouette Marked

"P-U" (3pcs)

Silhouette Marked

"P-T" (3pcs)

Set Screw

Nipple(-b)

Holder

Upper Fixture

Silhouette Marked

"P-U" (For all items)

Silhouette

Marked "P-U"

Silhouette Marked "P-U"

Silhouette

Marked "P-U"

Silhouette

Marked "P-T"

Silhouette

Marked "P-T"

Silhouette Marked "P-T"

Silhouette Marked

"P-T" (For CH55656)

Fig.1

110319

There are labels

attached on the

back of each

silhouette, such

as P-Y, P-L, P-T

and P-H.

Figure.1

P-Y (3pcs)

(For CH55456)

P-L (3pcs)

(For CH55556)

P-T (3pcs)

(For CH55656)

P-H (3pcs)

(For CH55756)

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

CH55456 / CH55556 / CH55656 / CH55756

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

Bulb Type A Max.100W

(not included)

Socket Ring