Installation Guide

ManualsBrandsCascadia ManualsSecurity Motion Detectors240-Degree Bronze LED Motion-Activated Flood Light with Dusk to Dawn and Timer

Page 1 / 5

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. This fixture requires a 120 VAC, 60 Hz power source.

4. For general safety and to avoid any possible damage to

the sensor, be sure the power is switched "off" before

adjustment.

Maximum Wattage: 25W±2.5W

Working Temperature Range: -4

F ~ 104

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

T0068 / T0098

Features

140613

Parts:

Parts Number (4540MM) For T0068

Parts Number (5078MM) For T0098

Mounting Screw (B)

Mounting Strap (A)

Rubber Pad (C)

Set Screw (D)

Decorative Cover (E)

Wire Nut (F)

1. Energy saving LED fixture.

2. Motion sensor: turns light ON automatically when

motion is detected and turns light OFF

automatically when motion stops.

3. Photocell keeps the light OFF during daylight

hours.

4. When in manual override mode, use wall switch

to keep the light ON during the night.

WARNING: Turn off the main power at circuit breaker before installing fixture.

AVERTISSEMENT: Coupez la source d’alimentation principale au panneau

central de disjoncteurs avant d’installer le luminaire.

“THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A

PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS

INVOLVED.”

“CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI

CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS.”

Summary of content (5 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS T0068 / T0098 WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Important to Know Features 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
NOTES: Fig. 1 Fig. 2 3 Connector Fig. 3 4 4 3 Rubber hose 2 1 Fig. 4 1 2 Wall wash light options： 1. Option 1: Up & Down light accent, the original setting of wall wash light is the up and down light accent. 2. Option 2: Down light accent only, unplug the connectors ( 1 and 3 , 2 and 4 ). (See Fig. 1) Then connect the connectors ( 1 and 2 , 3 and 4 ). (See Fig. 2) Slip rubber hose to fully cover the connectors ( 1 2 3 4 ). (See Fig. 3 / Fig. 4) 3.
PAGE 3
Motion Sensor and LED Light Head Adjustment ______________________________________________ 1. Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. (See Fig. 1) FIG.1 2. Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times when motion is detected). You can rotate the sensor head up and down, left and right to change the coverage area. (See Fig. 1 and Fig. 2) Collar Ball Joint sensor 3.
PAGE 4
. PC` MODE (nighttime operation only; on at dusk, off at dawn) The lights will brighten at dusk. Lights will turn off automatically at dawn 5. Manual Override (nighttime operation only; on at dusk, off at dawn) Set the switch at “OFF” or “AUTO” position, the light will be turn on in all night by switching the power off for 0.5 seconds~3 seconds then on again. Turn the power off for 5 seconds, the light will return to “OFF” mode or “AUTO” mode. (See Fig.6) Light will turn off automatically at dawn. Fig.
PAGE 5
Troubleshooting ---The light does not come on at all: 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring is correct. 3. Cover the sensor with dark color cloth to verify that the ambient light level is not too high. ---In TEST Mode, the light stays on over 5 seconds after motion is no longer detected: 1. Make sure the slide switch is at the TEST position. 2. Cover the sensor with a dark color cloth to verify that motion is not detected.