Installation Guide

ManualsBrandsCascadia ManualsLighting & Ceiling FansSmart Lighting 7-Pack 3-in Puck Light

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

X0029 / X0030 / X0031 / X0032 / X0033 / X0034

1. Read all instructions carefully before installation and operation. Save instructions for future reference.

2. If you are not familiar with national and local electrical codes, it is recommended that you consult with a qualified

electrician.

3. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock.

This plug will fit in a polarized outet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted . Do

not alter the plug.

3. Multiple fixtures can be linked in series: up to 10 puck lights from 1 power source.

4. Do not use in wet locations, use indoors only.

5. LEDs are non-replaceable. Do not attempt to open the light fixture.

6. LED light output is strong enough to cause eye damage. Avoid staring directly at the LED light source for prolonged

periods of time.

7. Specification:

Installation Steps

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Determine desired placement for mounting puck lights and control sensor unit. Be sure spacing of components does

not exceed maximum length of power cord (from outlet) and linking cables (from one component to the next). The

mounting surface should be a minimum of 0.5 inch thick.

Page 1 / 4

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

150414

Hardware Package (included):

36W Driver (A)

12" Linking Cord (B)

Mounting Screw (C)

Metal Disk (D)

Important to Know:

Turn off the power at fuse or circuit box.

Wood Screw (E)

Long Double-

sided Tape

Short Double-

sided Tape

NO.

Dimension(inch)

Item #:

X0030

X0029

1/2

Total

Watts

9 W

15 W

X0031

X0034

X0033

X0032

Body

color

Bronze

White

3-pack Kit

Details

3-pack Kit

7-pack Kit

5-pack Kit

7-pack Kit

5-pack Kit

21 W

9 W

15 W

21 W

1/2

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS X0029 / X0030 / X0031 / X0032 / X0033 / X0034 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
PAGE 2
Fig.1. Cabinet Wall Note 1: The recommended location for the undercabinet light fixture is near the front edge of the cabinet as shown in fig.1. This provides the best light distribution across the countertop. Note 2: Sensor control unit can be connected at the beginning, middle, or end of a series. Additional sensor units (sold separately) can be connected to a single series to provide multiple control points if desired.
PAGE 3
14. Plug the connector into the sensor and plug the driver into a 120V AC 60HZ outlet. (See Fig. 8) Fig.8. Fig.7. 12" Linking Cord (B) Cable Clip 36W Driver (A) Metal Disk (D) Outlet Turn on the power at the main fuse or circuit breaker box. Linking multiple fixtures: Multiple light fixtures can be linked up to a single driver by using a mini connector or by using additional linking cords. A. Using 12˝ linking cord: Fig.9. 1.
PAGE 4
Marking of sensor position Label This hardware package contains an indicator label. You may stick the label on the cabinet in order to mark the position of the sensor if so desired. Sensor Cleaning This light fixture is made from quality materials that will last for many years with minimum care. When cleaning, make sure you have unplugged your fixture, and have allowed sufficient time for the unit to cool to room temperature. Clean the housing and glass cover using a damp soft cloth.