Installation Guide

ManualsBrandsCascadia ManualsUnder Cabinet LightsUnder Cabinet LED 16-in Hardwired/Plug-in Strip Light

Installation Steps

10’ Power Cable

12” Link Cord

Dry Wall Screw

Switch Label

Cable Clip

Turn off the power at fuse or circuit box.

160127

1. Find a suitable location to mount the fixture, make sure that

your 10 ft. power cord will reach the nearest electrical

outlet. The mounting surface should be a minimum of 1/2”

thick.

Note: The recommended mounting position for under-cabinet

use is towards the front edge of the cabinet. This provides

even light distribution across the countertop surface

(as shown in Fig. 1).

Page 1 / 4

Important to Know

1. Read all instructions carefully before installation and operation.

2. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician.

3. Units can be linked together in series from one power supply. Link up to 7 x 8" bar lights (#X0035 or X0036) together,

link up to 5 x 16" bar lights (#X0037 or X0038) together, link up to 3 x 21" bar lights (#X0039 or X0040) together, or link

combination of sizes together.

4. Do not use in wet locations, use indoors only.

5. Non-replaceable LEDs.

6. Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to avoid eye damage.

7. Specification:

Important safety instructions.

1. Never use with an extension cord unless plug can be fully inserted.

2. Do not alter the plug.

3. Do not attempt to install fixture while it is plugged in.

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

X0035 / X0036 / X0037 / X0038 / X0039 / X0040

NO.

Dimension(inch)

Total

Watts

Item #:

X0035/X0036

X0037/X0038

X0039/X0040

0.75

2.75

0.75

2.75

0.75

2.75

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package (included):

Cabinet

Wall

Fig.1.

Counter Top

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS X0035 / X0036 / X0037 / X0038 / X0039 / X0040 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware Package (included): 10’ Power Cable 12” Link Cord Switch Label Dry Wall Screw Cable Clip Important to Know 1.
PAGE 2
. Remove the plastic plug on each side of the cabinet light. (See Fig. 2) Fig.2. 3. Place the light fixture against the mounting surface in the desired position and mark the location of the two key hole slots. Remove the light fixture from the mounting surface. Pre-drill holes in the mounting surface according to marks. Secure the dry wall screws to the cabinet. (Do not over tighten screws). The dry wall screw heads should protrude approximately 1/8” (3.
PAGE 3
Make sure the distance between cabinet lighting fixtures does not exceed the linking cord length. NOTE: The linking cord will only plug into one end correctly. Do not try to force it into the wrong receptacle as this could cause damage to the fixture. NOTE: If the linking cable sags. Peel away the waxed paper on the cable clip and stick to the bottom of the under cabinet. Fasten the linking cord with the cable clip. (See Fig.
PAGE 4
Cleaning instructions Your fixture is made from quality materials that will last for many years with minimum care. When cleaning, make sure you have unplugged your fixture, and have allowed sufficient time for the unit to cool to room temperature. You should clean the housing and lens using a damp soft cloth. You should plug your fixture back in only after the fixture has thoroughly dried. Trouble Shooting Minor problems often can be fixed without the help of an electrician.