Installation Guide

ManualsBrandsCascadia ManualsUnder Cabinet LightsUnder Cabinet LED 3-Pack 2.75-in Hardwired/Plug-in Puck Light

Dry Wall Screw

Switch Label

Cable Clip

Connector

36W Power Adaptor

48W Power Supply Box

(Sold Separately)

NO.

Dimension(inch)

Item #:

2.75

X0058/X0061/X0082

X0057/X0060/X0081

Total

Watts

15W

0.75

2.75

0.75

2.75

0.75

X0059/X0062/X0083

3-pack Kit

Details

7-pack Kit

5-pack Kit

21W

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Determine desired placement for mounting puck lights and control

sensor unit. Be sure spacing of components does not exceed

maximum length of power cord (from outlet) and linking cables

(from one component to the next). The mounting surface should be

a minimum of 0.5 inch thick.

3. The recommended location for the under-cabinet light fixture is near

the front edge of the cabinet as shown in fig.1. This provides the best

light distribution across the countertop.

Cabinet

Wall

Fig.1.

Counter Top

160225

Installation Steps

ØA

LOCATE DESIRED POSITION FOR PUCK LIGHT

Page 1 / 5

Important to Know

1. Read all instructions carefully before installation and operation. Save instructions for future reference.

2. If you are not familiar with national and local electrical codes, it is recommended that you consult with a qualified

electrician.

3. Multiple fixtures can be linked in series:

1 sensor plus up to 10 puck lights from 36W power adaptor or 1 sensor plus up to 15 puck lights from 48W power

supply box.

4. Do not use in wet locations, use indoors only.

5. LEDs are non-replaceable. Do not attempt to open the light fixture.

6. LED light output is strong enough to cause eye damage. Avoid staring directly at the LED light source for prolonged

periods of time.

7. Specification:

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

X0057 / X0058 / X0059 / X0060 / X0061 / X0062 / X0081 / X0082 / X0083

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package (included):

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Summary of content (5 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS X0057 / X0058 / X0059 / X0060 / X0061 / X0062 / X0081 / X0082 / X0083 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
PAGE 2
This fixture can be mounted in two ways。 A: For Surface Mounting: Fig.2 Turn off the power at fuse or circuit box. Lamp Housing NOTE: a. Sensor control unit can be connected at the beginning, middle, or end of a series. Additional sensor units (sold separately) can be connected to a single series to provide multiple control points if desired. Male Plug Female Plug b.
PAGE 3
Direct Wire 48W Power Supply Box (Purchased Separately) Conduit Cable Clip Female Plug Cable Clip Connector Male Plug Light Fixture Unit Sensor Control Unit 48W Power Supply Box Fig.4b B: Recessed Installation: Turn off the power at fuse or circuit box. Cabinet MOUNTING THE SENSOR CONTROL UNIT: 1. Locate desired position for puck light or sensor control. 2-3/8" 2. Drill a 2-3/8" hole in the desired location.(See Fig.5) CAUTION: If the hole is too big or small, the puck light cannot be installed.
PAGE 4
Function and Operation Choose an option by sliding the switch on the surface of the sensor control. (See Fig.9 ). When the switch is set to “ ”, the sensor is deactivated. When the switch is set to “ ”, the sensor 's active detection range is 4" below the fixture. When the switch is set to “ ”, the sensor 's active detection range is 8" below the fixture. Fig.9 NOTE: This under cabinet light fixture has a memory function.
PAGE 5
Trouble Shooting Minor problems often can be fixed without the help of an electrician. Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock. PROBLEM Light will not come ON. CORRECTIVE ACTION POSSIBLE CAUSE 1. Power is off. 2. Bad plug connection. 3. Switch is in Lock Mode with power off. 1. Check if power supply is on. 2. Check power cord. 3. Move switch to 4" or 8" sensor range. Fuse blows or circuit breaker 1. Discontinue use.