User manual

Operation Guide 5222
E-29
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
When the end of the countdown is reached, the alarm x
sounds for 10 seconds or until you stop it by pressing any
button. The countdown time is reset to its starting value
automatically after the alarm stops.
The countdown timer operation continues even if you exit x
the Countdown Timer Mode.
Press x D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
To completely stop a countdown operation, fi rst pause x
it (by pressing D), and then press A. This returns the
countdown time to its starting value.
E-28
To confi gure the countdown timer
While the countdown start time is on the display in the 1.
Countdown Timer Mode, hold down A until the current
countdown start time starts to fl ash, which indicates the
setting screen.
If the countdown start time is not displayed, use the x
procedure under “To use the countdown timer” (page
E-29) to display it.
When the setting you want to change is fl ashing, use 2. B
and D to change it.
Setting Screen Button Operation
Start Time
Use D (+) and B (–) to change the setting.
• You can set a start time in the range of 1 minute to
60 minutes in 1-minute increments.
Press 3. A to exit the setting screen.
E-27
Countdown Timer
The countdown timer can be set within a range of
one minute to 60 minutes. An alarm sounds when the
countdown reaches zero.
All of the operations in this section are performed in the x
Countdown Timer Mode, which you enter by pressing C
(page E-7).
Seconds
Minutes
E-26
To measure times with the stopwatch
Elapsed Time
D D D D A
Start Stop Re-start Stop Clear
Split Time
D A A D A
Start Split
(SPL indicator
displayed)
Split release Stop Clear
Two Finishes
D A D A A
Start Split
First runner
fi nishes. Display
time of fi rst
runner.
Stop
Second runner
fi nishes.
Split release
Display time of
second runner.
Clear
E-25
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two fi nishes.
The display range of the stopwatch is 59 minutes, x
59 seconds.
The stopwatch continues to run, restarting from zero after x
it reaches its limit, until you stop it.
The stopwatch measurement operation continues even if x
you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen x
on the display clears the split time and returns to elapsed
time measurement.
All of the operations in this section are performed in the x
Stopwatch Mode, which you enter by pressing C (page
E-7).
SPL indicator
Seconds
Minutes
E-24
Alarm On
Signal On
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
The alarm on indicator and hourly time signal on indicator are shown in all modes. x
The alarm on indicator fl ashes while the alarm is sounding. x
E-23
To turn the alarm and the hourly time signal on and off
In the Alarm Mode, you can use 1. D to cycle through the
available alarm and hourly time signal combinations as
shown below.
Hourly time signal
on indicator
Alarm on indicator
E-22
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode
the watch is in.
Alarm and Hourly Time Signal operations are performed in accordance with the x
Timekeeping Mode digital time.
To stop the alarm tone after it starts to sound, press any button. x
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-21
To set an alarm time
In the Alarm Mode, hold down 1. A until the hour setting
of the alarm time starts to fl ash, which indicates the
setting screen.
This operation automatically turns on the alarm. x
Press 2. C to move the fl ashing between the hour and
minute settings.
While a setting is fl ashing, use 3. D (+) and B (–) to
change it.
When setting the alarm time using the 12-hour format, take care to set the time x
correctly as a.m. (no indicator) or p.m. (P indicator).
Press 4. A to exit the setting screen.
E-20
Alarm
You can set one Daily Alarm. When the alarm is turned on,
the alarm tone sounds when the alarm time is reached.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
Pressing x D cycles through the available alarm and
hourly time signal combinations (page E-23).
All of the operations in this section are performed in the x
Alarm Mode, which you enter by pressing C (page E-7).
Alarm time
(Hour : Minutes)
Hourly time signal
on indicator
Alarm on indicator