User Manual
Table Of Contents
- Getting Ready
- Contents
- About This User’s Guide
- Chapter 1 Getting Acquainted
- Chapter 2 Using the Main Application
- 2-1 Main Application Overview
- 2-2 Basic Calculations
- 2-3 Using the Calculation History
- 2-4 Function Calculations
- 2-5 List Calculations
- 2-6 Matrix and Vector Calculations
- 2-7 Using the Action Menu
- 2-8 Using the Interactive Menu
- 2-9 Using the Main Application in Combination with Other Applications
- 2-10 Using Verify
- Chapter 3 Using the Graph & Table Application
- Chapter 4 Using the Conics Application
- Chapter 5 Using the 3D Graph Application
- Chapter 6 Using the Sequence Application
- Chapter 7 Using the Statistics Application
- 7-1 Statistics Application Overview
- 7-2 Using List Editor
- 7-3 Before Trying to Draw a Statistical Graph
- 7-4 Graphing Single-Variable Statistical Data
- 7-5 Graphing Paired-Variable Statistical Data
- 7-6 Using the Statistical Graph Window Toolbar
- 7-7 Performing Statistical Calculations
- 7-8 Test, Confidence Interval, and Distribution Calculations
- 7-9 Tests
- 7-10 Confidence Intervals
- 7-11 Distribution
- 7-12 Statistical System Variables
- Chapter 8 Using the Geometry Application
- Chapter 9 Using the Numeric Solver Application
- Chapter 10 Using the eActivity Application
- Chapter 11 Using the Presentation Application
- Chapter 12 Using the Program Application
- Chapter 13 Using the Spreadsheet Application
- Chapter 14 Using the Setup Menu
- Chapter 15 Configuring System Settings
- 15-1 System Setting Overview
- 15-2 Managing Memory Usage
- 15-3 Using the Reset Dialog Box
- 15-4 Initializing Your ClassPad
- 15-5 Adjusting Display Contrast
- 15-6 Configuring Power Properties
- 15-7 Specifying the Display Language
- 15-8 Specifying the Font Set
- 15-9 Specifying the Alphabetic Keyboard Arrangement
- 15-10 Optimizing “Flash ROM”
- 15-11 Specifying the Ending Screen Image
- 15-12 Adjusting Touch Panel Alignment
- 15-13 Viewing Version Information
- Chapter 16 Performing Data Communication
- Appendix
20050501
Variable Manager Folder Operations
This section describes the various folder operations you can perform using the Variable
Manager.
k Specifying the Current Folder
The “current folder” is the folder where the variables created by applications (excluding
eActivity) are stored and from which such variables can be accessed. The initial default
current folder is the “main” folder.
You can also select a folder you created yourself as the current folder.
u ClassPad Operation
(1) Start up the Variable Manager and display the folder list.
(2) Tap the [Current] down arrow button. On the list that appears, select the folder that you
want to specify as the current folder.
(3) Tap [Close] to close the folder list.
k Creating a New Folder
You can use the following procedure to create up to 87 folders, as you need them.
u ClassPad Operation
(1) Start up the Variable Manager, which causes the folder list to appear.
(2) On the folder list, tap [Edit] and then [Create Folder].
• This displays a dialog box for inputting a folder name.
(3) Enter the folder name, and then tap [OK].
• This creates the new folder and returns to the folder list.
• Normally, a folder name can contain up to eight bytes. If your folder name includes 2-byte
characters, you may not be able to input eight characters for the folder name. For details
about folder names, see page 1-7-5.
Current folder
1-8-3
Using the Variable Manager
• An error message appears and your folder is not created if there is already a folder with the same
name you input. Tap [OK] to close the error message dialog box, and then specify a different
name for the folder you are creating.
Tip