User manual - DT-300M60E

ManualsBrandsCasio ManualsHandheldsDT-300M60E

E-3

Danger!

■ Handling Alkaline Batteries

● Should fluid from the battery accidentally get into your eyes, there is a threat

of loss of eyesight, do not rub them. Immediately rinse your eyes with clean

tap water and then consult a physician immediately.

Warning!

■ Handling Alkaline Batteries

● Do not put the battery in a fire, expose it to heat, dismantle or modify it. If the

insulation or safety valve is damaged, the battery may leak fluid, overheat or

explode.

● Do not insert the battery with the poles reversed. Doing so may cause some

abnormality or a short and the battery may leak fluid, overheat or explode.

● Keep the battery out of the reach of children. If the battery is swallowed,

contact a physician immediately.

● If the alkali fluid gets in your mouth, rinse your mouth with water and contact

a physician immediately.

● If the alkali fluid gets on your skin or clothes, it may burn your skin,

thoroughly rinse the affected area with tap water.

● Do not store batteries with metal objects such as necklaces or hairpins,

doing so may cause the positive and negative poles to be shorted.

● Do not mix new and old batteries or other makes of batteries. The different

attributes may cause the battery to leak fluid, overheat or explode.

● This battery was not made to be recharged. Recharging this battery may

damage the insulation or internal structure and may cause the battery to leak

fluid, overheat or explode.

● Do not damage or remove the label on the exterior of the battery. Doing so

may cause the battery to short, leak fluid, overheat or explode.

● Do not drop, throw or expose the battery to extreme impact. Doing so may

cause the battery to leak fluid, overheat or explode.

● Do not alter the shape of the battery. If the insulation or safety valve is

damaged, the battery may leak fluid, overheat or explode.

Summary of content (27 pages)

PAGE 1
Danger! ■ Handling Alkaline Batteries ● Should fluid from the battery accidentally get into your eyes, there is a threat of loss of eyesight, do not rub them. Immediately rinse your eyes with clean tap water and then consult a physician immediately. Warning! ■ Handling Alkaline Batteries ● Do not put the battery in a fire, expose it to heat, dismantle or modify it. If the insulation or safety valve is damaged, the battery may leak fluid, overheat or explode.
PAGE 2
Warning! ■ Disassembly and Modification ● Never try to disassemble or modify the unit in any way. High voltage inside creates the danger of electrical shock. ■ Interior Parts and Components ● Never touch interior high-voltage parts or components. Doing so creates the danger of electrical shock. ■ Abnormal Conditions ● Should the unit become hot or start to emit smoke or a strange odor, immediately turn off the power and contact your original dealer or an authorized CASIO service provider.
PAGE 3
Warning! ■ Optional Bridge Satellite Cradle ● Power the Bridge Satellite Cradle only with a power outlet whose voltage matches that marked on the Bridge Satellite Cradle. Do not plug the Bridge Satellite Cradle into an extension shared by other appliances. Doing so creates the danger of fire and electrical shock. ● Avoid conditions that can cause damage or breaks in the power cord. Do not place heavy objects on the power cord. Keep it away from sources of heat.
PAGE 4
Caution! ■ Handling Alkaline Batteries ● Store batteries someplace out of direct sunlight where the temperature and humidity are not high. Not doing so may cause the batteries to leak fluid, overheat or explode. Also, it may cause the life and performance of the batteries to decline. ● Follow the regulations of the local government when disposing of these batteries. ■ Make back-up copies of all important data ● Note that CASIO Computer Co., Ltd.
PAGE 5
Caution! ■ Optional Bridge Satellite Cradle ● Keep the power cord away from stoves and other sources of extreme heat. Heat can melt the insulation of the power cord and create the danger of fire and electrical shock. ● Never pull on the power cord when unplugging it. Doing so can damage the cord and create the danger of personal injury, fire and electrical shock. Always hold onto the plug when unplugging it from the wall outlet. ● Never touch the plug while your hands are wet.
PAGE 6
Contents Safety Precautions ............................................... E-2 Unpacking ............................................................. E-9 Important ............................................................. E-10 Handling Precautions ........................................................... E-10 Service ................................................................................. E-10 System Diagram .................................................. E-11 General Guide ............
PAGE 7
Unpacking The following items are included in the package with the product. If for some reason anything is damaged or missing, please contact the store where you purchased the product.
PAGE 8
Important Carefully read the following points to get the best performance and long life from your Handheld Terminal. Handling Precautions • Use only your finger or a blunt object to operate the stroke keys. Use of a sharp pointed object can damage stroke keys and cause shorting of internal circuitry. • Use a soft dry cloth when cleaning the Handheld Terminal. Do not wipe it with a wet cloth.
PAGE 9
System Diagram Options Bridge Satellite Cradle Bridge Satellite Cradle AC Adaptor DT-364IO DT-9020ADP Bridge Satellite Cradle Cables DT-300M60E RS-232C Cable DT-887AX/AXA Bridge Satellite Cradle PC Connection Cable RS-422 Cable DT-888RSC Bridge Satellite Cradle Chain Connection USB Cable DT-380USB Bridge Satellite Cradle PC Connection Cablel 9 pin Socket E-11
PAGE 10
General Guide 1 9 2 8 1 3 6 11 4 5 10 7 13 7 12 1 Reader port Emits a laser that reads bar codes 2 Read indicator LED Indicates the status of the read operation: green for a successful read, red for an unsuccessful read. * 3 LCD screen Displays information about the programs being run. 4 Read key Pressing this key activates the bar code reader. 5 Stroke key A total of 18 keys are provided for operations and to turn the power on and off.
PAGE 11
Battery Replacement Power Supply Operating the Handheld Terminal requires two AA (LR6) alkaline batteries. Replace the AA (LR6) alkaline batteries as soon as the battery display on the LCD screen ). shows that the battery is empty ( [Warning] ■ Make a Backup of Important Data • The Handheld Terminal is equipped with an internal backup rechargeable battery. This battery is used as a backup power supply and cannot be removed.
PAGE 12
Replacing the Main Batteries (AA Alkaline Batteries) Important! • Note the polarity (orientation of the and the ) of the AA alkaline batteries when installing them. • Be sure to turn off the power before removing the batteries. • Remove the batteries if you are not going to use the Handheld Terminal for an extended period of time. Loading the Main Batteries 1 2 3 E-14 Slide the main battery compartment cover lock upwards and remove the main battery compartment cover.
PAGE 13
About the LCD Screen The LCD screen of the Handheld Terminal shows program settings, operational procedures, and calculation results and other information.
PAGE 14
Attaching the Wrist Strap Use the wrist strap to protect the Handheld Terminal from being accidentally dropped while you are carrying it. To Attach the wrist strap Attach the wrist strap as shown below. 1 2 Pass the thin end of the wrist strap through the metal hand strap mount on the bottom side of the Handheld Terminal. Double the strap back through its own loop, and pull it tight. Important! E-16 • Never swing the Handheld Terminal around by its wrist strap.
PAGE 15
Keys and Their Functions The Handheld Terminal has 18 stroke keys and one read key. Stroke Keys and Their Functions. 1 2 3 4 5 1 5 3 7 8 6 6 7 4 2 9 8 9 Read key Press this key to read a bar code. Clear key Press this key to cancel input. Backspace key Press this key to erase the character to the left of the cursor. This key can be set to do other functions, except for reading bar codes. 10-key pad Press these keys to enter numbers 0 to 9 in the number input mode.
PAGE 16
Using the Bar Code Reader Performing Bar Code Read Operation 1 Turn the power on, and then position the reader port about 4 cm or more from the bar code and press the read key. Reader port Read indicator LED Read key Power key 2 The reader port emits a laser to read the bar code. The read indicator lights green when the read is successful.
PAGE 17
About Warning Label • This class 2 laser product warning label conforms with IEC 60825. • The class 2 laser emission is only exposed momentarily, but under no circumstances should you look directly into the laser beam. • Operations not mentioned in this guide are dangerous and should not be done under any circumstances. • The maximum laser output is less than 1 mW at a wavelength of 650 nm.
PAGE 18
Data Communication Communication Between Handheld Terminals You can use the infrared interface port, located on the bottom of the Handheld Terminal, to transfer applications or data to another Handheld Terminal. Set the communication format for two Handheld Terminals as shown below. Make sure that the infrared interface ports on both the units do not shift. Communication is possible if the Handheld Terminals are in direct contact or from up to 20 cm.
PAGE 19
Specifications 1. General CPU: Memory: 32-bit RISC Type RAM : 2 MB (User area 1.3 MB) FROM: 8 MB (User area 5.9 MB) 2. Display Type: Resolution: Display contrast: Backlight: STN LCD with phase correction film 112 x 64 dots Adjustable through key operation LED backlight 3. Laser Scanner Readable Codes: Reading Distance: JAN, EAN, UPC, NW-7, CODE39, ITF, CODE93, CODE128 (EAN128), MSI, Industrial 2 of 5, IATA Approximately 4 to 30 cm 4. Input Stroke Keys: Read Key: 18 1 5.
PAGE 20
Specifications 8. Operating Environment Temperature: -5 to 50C° Humidity: 30% to 80% RH Dust and Water splash proof: IP54 Drop durability: 150 cm 9.
PAGE 21
Using the Bridge Satellite Cradle You can transfer data (upload and download) between the Handheld Terminal and a personal computer by connecting the Bridge Satellite Cradle (DT-364IO). Use an RS-232C cable (DT-887AX/AXA) or a USB cable (DT-380USB) to connect the Bridge Satellite Cradle to the personal computer.
PAGE 22
Using the Bridge Satellite Cradle 1 USB interface 2 RS-232C interface 3 4 5 Used to connect the Handheld Terminal to a personal computer and transfer data (upload and download) to or from the Handheld Terminal. You need to install a dedicated driver on the personal computer before connecting it to the PC. Used to connect the Handheld Terminal to a personal computer and transfer data (upload and download) to or from the Handheld Terminal.
PAGE 23
Power Hook Up and Connections Use the AC adaptor (DT-9020ADP) for the Bridge Satellite Cradle sold separately for the Bridge Satellite Cradle power supply. Be sure to hook up the AC adaptor and the Bridge Satellite Cradle before transmitting data to or from the Handheld Terminal. The Handheld Terminal draws its power directly from the Bridge Satellite Cradle.
PAGE 24
Using the Bridge Satellite Cradle 4 5 Turn on the power switch. The power indicator LED lights red. Place the infrared interface port on the Handheld Terminal and the infrared interface port on the Bridge Satellite Cradle so that they are in direct contact. The power indicator LED on the Bridge Satellite Cradle lights green. · If the system is operating correctly, and it goes into transmission status, then the system operation LED flashes green.
PAGE 25
Connecting Multiple Bridge Satellite Cradles Use the modular cable for the connections. You can daisy chain multiple Bridge Satellite Cradles by connecting the C-OUT port of the first unit that is the nearest to the host computer to the C-IN port of the next unit that is sitting to the first unit with DT-888RSC cable (Daisy chain connection cable) as shown in the figure below.
PAGE 26
Using the Bridge Satellite Cradle DIP Switch Settings The DIP switches are located on the bottom of the Bridge Satellite Cradle. The DIP switches can be set to on or off. Turn off the power before setting the DIP switches.
PAGE 27
DT-364IO Bridge Satellite Cradle Specifications 1. Infrared Transmission Interface: Standard: Synchronization: Speed: Infrared interface Conforms to IrDA Ver 1.1 Asynchronous 9,600/115,200 bps/4M bps (Only when the host computer is connected via USB.) 2. RS-232 Control Protocol: Synchronization: Speed Half-duplex Asynchronous 115,200 bps 3. RS-422 Control Protocol: Synchronization: Speed Half-duplex Asynchronous 115,200 bps 4. USB Standard Speed; USB Ver. 1.1 12 Mbps (Max.) 5.