MA2207-EA © 2022 CASIO COMPUTER CO., LTD.
Watch Operation Guide 5698 Precautions ● ● Operating Precautions ● Water Resistance ● The information below applies to watches with WATER RESIST or WATER RESISTANT marked on the back cover.
Watch Operation Guide 5698 ● Temperature ● ● Never leave your watch on the dashboard of a car, near a heater, or in any other location that is subject to very high temperatures. Do not leave your watch where it will be exposed to very low temperatures. Temperature extremes can cause your watch to lose or gain time, to stop, or otherwise malfunction. Leaving your watch in an area hotter than +60 °C (140 °F) for long periods can lead to problems with its LCD.
Watch Operation Guide 5698 ● Bacteria and Odor Resistant Band ● The bacteria and odor resistant band protects against odor generated by the formation of bacteria from sweat, which ensures comfort and hygiene. In order to ensure maximum bacteria and odor resistance, keep the band clean. Use an absorbent soft cloth to thoroughly wipe the band clean of dirt, sweat, and moisture. A bacteria and odor resistant band suppresses the formation of organisms and bacteria.
Watch Operation Guide 5698 Battery ● ● The special rechargeable battery used by your watch is not intended to be removed or replaced by you. Use of a rechargeable battery other than the special one specified for your watch can damage your watch. The rechargeable (secondary) battery is charged when the solar panel is exposed to light, so it does not require regular replacement as the primary battery requires.
Watch Operation Guide 5698 Before Getting Started... General Guide ① Watch Face and Display Indicators ② ① This section provides an overview of the watch and introduces convenient ways it can be used. Watch Features ● ③ World Time Display the current time in any one of 38 time zones* around the globe. * Subject to being updated when connected with a phone. ● Alarm An alarm sounds whenever a time specified by you is reached.
Watch Operation Guide 5698 Navigating Between Modes Each press of (C) cycles between watch modes. ● In any mode, hold down (C) for at least one second to return to the Timekeeping Mode. Timekeeping Mode Cycling Between Timekeeping Mode Digital Display Contents Each press of (A) in the Timekeeping Mode toggles between the display information as shown below. Hours, minutes Charging This watch runs on power supplied from a rechargeable (secondary) battery that is charged by a solar panel.
Watch Operation Guide 5698 ● Checking the Charge Level ● Dead Battery ● Charging Time Guidelines In the Timekeeping Mode, the function hand indicates the current charge level. The digital display will go blank if the battery goes dead. Memory data is lost, and watch settings are returned to their initial factory defaults. The table below shows guidelines for approximate charging times.
Watch Operation Guide 5698 ● Power Saving Function ● Specifying the Illumination Duration Leaving the watch in a dark location for about one hour between the hours of 10 p.m. and 6 a.m. will cause the display to go blank, and the watch to enter Level 1 power saving. If the watch is left in this condition for six or seven days, the watch will enter Level 2 power saving. You can select either 1.5 seconds or three seconds as the illumination duration. 1. Enter the Timekeeping Mode.
Watch Operation Guide 5698 Linking with a Phone 4. Y Perform the operation shown on the screen of the phone to be paired with. When a connection is established between the watch and phone, [CNCT] will stop flashing. While there is a Bluetooth connection between the watch and phone (Mobile Link), the watch’s current time setting is adjusted automatically. You can also change the watch’s other settings. ● Note ● ● This function is available only while CASIO WATCHES is running on the phone.
Watch Operation Guide 5698 ● Triggering Immediate Time Adjustment The watch’s time setting will be adjusted automatically whenever you establish a connection between the watch and a phone. Whenever you want to trigger immediate time adjustment, perform the procedure below to connect with a phone. Viewing Stopwatch Data This section explains how to send lap times (up to 200 records) that are stored in watch memory, as well as other data to your phone for viewing with CASIO WATCHES.
Watch Operation Guide 5698 ● Configuring the Summer Time Setting 1. Y Tap the “CASIO WATCHES” icon. 2. X Hold down (C) for at least three seconds until [CNCT] starts to flash. Release the button when the function hand moves to ● Swapping Your World Time and Home Time 1. Y Tap the “CASIO WATCHES” icon. 2. X Hold down (C) for at least three seconds e. When a connection is established between the watch and phone, [CNCT] will stop flashing.
Watch Operation Guide 5698 2. X If the watch is in any mode besides the Timekeeping Mode, hold down (C) for at least one second to enter the Timekeeping Mode. 3. X Hold down (D) for at least three seconds. Release the button when [FIND] starts to flash at low speed. The phone will sound a tone when it establishes a connection with the watch. ● It will take a few seconds before the phone tone sounds. Changing the Home City Summer Time Setting 1. Y Tap the “CASIO WATCHES” icon. 2.
Watch Operation Guide 5698 Connection Note Connecting with a Phone Your watch can connect with a phone that is paired with it. ● If the watch is not paired with the phone you want to connect with, refer to the information below and pair them. l C Pair the watch with a phone. ● Connecting with a Phone ● 3. X Press (C) twice. The connection will be terminated if you do not perform any operation on the watch or phone for a fixed amount of time.
Watch Operation Guide 5698 Time Adjustment Your watch can connect with a phone to obtain information that it uses to adjust its date and time setting. If your watch cannot connect with a phone for some reason, you can use watch operations to adjust date and time settings.
Watch Operation Guide 5698 3. Keep pressing (C) until the setting you want to change is flashing. ● 4. Configure the date and time settings. ● Each press of (C) moves the flashing to the next setting in the sequence shown below. ● Home City Summer time To reset the seconds to 00: Press (D). 1 is added to the minutes when the current count is between 30 and 59 seconds. For all the other settings, use (B) and (D) to change the flashing setting.
Watch Operation Guide 5698 Using the Watch in a Medical Facility or Aircraft Whenever you are in a hospital, on an aircraft, or in any other location where connection with a phone may cause problems, you can perform the procedure below to disable auto time adjustment. To re-enable auto time adjustment, perform the same operation again. World Time World Time lets you look up the current time in any one of 38 cities around the globe, and UTC (Coordinated Universal Time). ● l Navigating Between Modes 2.
Watch Operation Guide 5698 Alarm Note ● ● ● While the setting is being configured, the watch will exit the setting operation automatically after about two or three minutes of non-operation. While [UTC] is selected as the city, you will not be able to change or check the summer time setting. If you select a World Time City with CASIO WATCHES and then change to a different city with a watch operation, the CASIO WATCHES city information is deleted from the watch.
Watch Operation Guide 5698 ● To stop the alarm Turning Off an Alarm or the Hourly Time Signal Pressing any button while the beeper is sounding stops it. Note ● ● A beeper sounds for 10 seconds when an alarm time is reached. The watch will automatically return from the Alarm Mode to the Timekeeping Mode if you do not perform any operation for about two or three minutes. To stop an alarm or the hourly time signal from sounding, perform the steps below to turn it off.
Watch Operation Guide 5698 Moving to Another Time Zone Use the procedure below to easily change day and time settings of the watch to a destination location. ● After Arriving Stopwatch 1. Swap the origin time zone time with the destination time zone time. Before swapping After swapping Destination time ● Before Boarding The stopwatch measures elapsed time in 1/100-second units for the first hour, and in 1second units after that for up to 24 hours.
Watch Operation Guide 5698 Split Times and Lap Times ● Split time A split time is the time elapsed from the start, up to any point along the course of an event. D Start Measuring Elapsed Time 1. Enter the Stopwatch Mode. l Navigating Between Modes 2. Use the operations below to measure Measuring a Split Time 1. Enter the Stopwatch Mode. l Navigating Between Modes ● elapsed time. Split 1 Start A Stop Split 2 2. Press (A) to display [SPL].
Watch Operation Guide 5698 Timer Setting the Countdown Start Time The timer counts down from a start time specified by you. A beeper sounds when the end of the countdown is reached. The start time can be set in 1-second units up to 60 minutes. Measuring Lap Times 1. Enter the Stopwatch Mode. l Navigating Between Modes ● If a stopwatch timing operation is in progress, press (D) to stop it and then press (A) to reset the stopwatch to all zeros before performing the operation in step 2.
Watch Operation Guide 5698 Using the Timer 1. Enter the Timer Mode. l Navigating Between Modes Minutes, seconds Timer Countdown Indication 30 minutes before the end of a timer operation is reached, a countdown start tone sounds and the function hand starts to indicate the remaining time until the end of the timer operation. ● The countdown start tone will not sound when the timer start time is 30 minutes or less. 2. Use the operations below to perform a Function hand timer operation.
Watch Operation Guide 5698 Other Settings 4. Press (C). This enables adjustment of the hour and minute hands. Minute hand This section explains other watch settings you can configure. Hour hand Changing the Date Display Format Specifying the Day of the Week Language You can select any one of six languages for the day of the week display in the Timekeeping Mode. 1. Enter the Timekeeping Mode. l Navigating Between Modes 2.
Watch Operation Guide 5698 Disabling the Countdown Start Tone You can use the procedure below to enable or disable the countdown start tone that sounds when the function hand starts a countdown operation 30 minutes before an alarm time or before the end of a timer operation. Use the procedure below to enable or disable the tone that sounds when you press a button. 1. Enter the Timekeeping Mode. 1. Enter the Timekeeping Mode. l Navigating Between Modes 2.
Watch Operation Guide 5698 Resetting Watch Settings This section explains how to return the watch settings below to their initial factory defaults. ● Watch Settings ● Stopwatch ● Timer ● Alarm Other Information This section provides non-operational information you also need to know. Refer to this information as required. City Table 1. Enter the Timekeeping Mode. City l Navigating Between Modes 2.
Watch Operation Guide 5698 City Name Summer Time Start Summer Time End London 02:00, last 01:00, last Sunday in Sunday in March October Paris 03:00, last 02:00, last Sunday in Sunday in March October Athens 04:00, last 03:00, last Sunday in Sunday in March October Tehran 00:00, 00:00, March 22 September 22 or or 21 21 Sydney, Adelaide 02:00, first Sunday in October 03:00, first Sunday in April 02:00, first Lord Howe Sunday in Island October 02:00, first Sunday in April 02:00, last Wellington
Watch Operation Guide 5698 Copyrights and Registered Copyrights ● ● ● ● ● ● The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by CASIO Computer Co., Ltd. is under license. iPhone and App Store are trademarks of Apple Inc. in the United States and other countries. iOS is a trademark or registered trademark of Cisco Systems, Inc. GALAXY is a registered trademark of Samsung Electronics Co., Ltd.
Watch Operation Guide 5698 Q2 I can’t connect while my phone is in the Airplane Mode. Connection with the watch is not possible while the phone’s Airplane Mode is enabled. After disabling the phone’s Airplane Mode, go to the phone’s Home Screen and tap the “CASIO WATCHES” icon. Next, on the watch, hold down (C) for at least three seconds. Auto Time Adjustment by Bluetooth Connection (Time Adjustment) Phone-Watch Connection Q1 I can’t establish a connection between the phone and watch.
Watch Operation Guide 5698 Alarm and Hourly Time Signal Q1 An alarm does not sound. Is the watch’s battery charged? Keep the watch exposed to light until it recharges sufficiently. l Charging Q3 The hands suddenly start moving at high speed. This is due to the reason (or one of the reasons) below, and does not indicate malfunction. Simply wait until normal hand movement resumes. ● ● Other than the above. The alarm’s settings may not be configured. Configure the alarm settings.
