User Manual
Table Of Contents
- Contents
- Getting Acquainted — Read This First!
- Chapter 1 Basic Operation
- Chapter 2 Manual Calculations
- 1. Basic Calculations
- 2. Special Functions
- 3. Specifying the Angle Unit and Display Format
- 4. Function Calculations
- 5. Numerical Calculations
- 6. Complex Number Calculations
- 7. Binary, Octal, Decimal, and Hexadecimal Calculations with Integers
- 8. Matrix Calculations
- 9. Vector Calculations
- 10. Metric Conversion Calculations
- Chapter 3 List Function
- Chapter 4 Equation Calculations
- Chapter 5 Graphing
- 1. Sample Graphs
- 2. Controlling What Appears on a Graph Screen
- 3. Drawing a Graph
- 4. Saving and Recalling Graph Screen Contents
- 5. Drawing Two Graphs on the Same Screen
- 6. Manual Graphing
- 7. Using Tables
- 8. Modifying a Graph
- 9. Dynamic Graphing
- 10. Graphing a Recursion Formula
- 11. Graphing a Conic Section
- 12. Drawing Dots, Lines, and Text on the Graph Screen (Sketch)
- 13. Function Analysis
- Chapter 6 Statistical Graphs and Calculations
- 1. Before Performing Statistical Calculations
- 2. Calculating and Graphing Single-Variable Statistical Data
- 3. Calculating and Graphing Paired-Variable Statistical Data (Curve Fitting)
- 4. Performing Statistical Calculations
- 5. Tests
- 6. Confidence Interval
- 7. Distribution
- 8. Input and Output Terms of Tests, Confidence Interval, and Distribution
- 9. Statistic Formula
- Chapter 7 Financial Calculation
- Chapter 8 Programming
- Chapter 9 Spreadsheet
- Chapter 10 eActivity
- Chapter 11 Memory Manager
- Chapter 12 System Manager
- Chapter 13 Data Communication
- Chapter 14 Geometry
- Chapter 15 Picture Plot
- Chapter 16 3D Graph Function
- Chapter 17 Python (fx-CG50, fx-CG50 AU only)
- Chapter 18 Distribution (fx-CG50, fx-CG50 AU only)
- Appendix
- Examination Modes
- E-CON4 Application (English)
- 1. E-CON4 Mode Overview
- 2. Sampling Screen
- 3. Auto Sensor Detection (CLAB Only)
- 4. Selecting a Sensor
- 5. Configuring the Sampling Setup
- 6. Performing Auto Sensor Calibration and Zero Adjustment
- 7. Using a Custom Probe
- 8. Using Setup Memory
- 9. Starting a Sampling Operation
- 10. Using Sample Data Memory
- 11. Using the Graph Analysis Tools to Graph Data
- 12. Graph Analysis Tool Graph Screen Operations
- 13. Calling E-CON4 Functions from an eActivity
14-59
14. Perform the following operation: 6(Animate) – 3:Trace.
• This specifies point D (the one you selected in step 13) as the “trace point”.
15. Perform the following operation: 6(Animate) – 5:Go (once).
• This should cause a parabola to be traced on the
display. Note that line segment AB is the directrix and
point C is the focus of the parabola.
Note
• All of the points that are currently selected on the screen become trace points when you
perform the following operation: 6(Animate) – 3:Trace. This operation also cancels Trace
for any point that is currently configured as a trace point.
• The calculator’s auto power off feature will turn off power if an animation is being performed.
If calculator power is turned off (either by auto power off or manually) while an animation is
being performed, the animation will be stopped.
u To edit an animation
Example: While the animation screen created with the procedure under “To trace
a locus of points”, use the Edit Animations screen to edit the animation
1. While the animation screen you want to edit is on the display, perform the following
operation: 6(Animate) – 4:Edit Animation.
• This will display the Edit Animations screen.
2. Edit the animation using one of the procedures below.
When you want to do
this:
Perform this procedure:
Specify how many times
the animation should
be executed when you
perform the operation:
6(Animate) –
6:Go (repeat)
1. Use c and f to move the highlighting on the Edit
Animations screen to “Times” and then press 1(Times).
→
2. On the dialog box that appears, input the number of repeats
you want to specify and then press w.
• Inputting 0 here will cause the animation to repeat until
you press J or o stop it.