E Handheld Printer Terminal Series User’s Guide Be sure to read “Safety Precautions” inside this guide before trying to use your Handheld Printer Terminal. After reading this guide, keep it in a safe place for future reference. PN410385-007 IT-3000_E_Hyo_1_4.p65 3 07.10.
• This Product is equipped with the Brycen B-RAPPORE Stack and My Wirefree Network Bluetooth User Interface Application, the use of which is governed by a license granted by Brycen Co., Ltd. ® • BLUETOOTH is a registered trademark owned by Bluetooth SIG, Inc. and licensed to CASIO COMPUTER CO., LTD. • Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Datalight is a registered trademark of Datalight, Inc.
Safety Precautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the first time. Markings and Symbols The following are the meanings of the markings and symbols used in these Safety Precautions. Danger This symbol indicates information that, if ignored or applied incorrectly, creates the danger of death or serious personal injury.
Safety Precautions Warning Foreign Objects • Should any foreign matter get into the Handheld Printer Terminal and its options, immediately turn off the power and contact your original vendor or an authorized CASIO service provider. Continued use creates the danger of fire and electric shock. Dropping and Damage • Should you drop the Handheld Printer Terminal and its options and damage them, immediately turn off the power and contact your original vendor or an authorized CASIO service provider.
Operation of Wireless Data Communication Function Warning Interference with the Operation of Other Equipment (Using Wireless Data Communication Function) • Please follow the instructions provided by health care facilities when using your Handheld Printer Terminal in hospitals or other locations where medical equipment is in use.
Safety Precautions Caution Foreign Objects • Take care to ensure that metals or combustible objects are not inserted into the openings of the Handheld Printer Terminal and its options. Such objects inside of the Handheld Printer Terminal and its options create the danger of fire and electric shock. Location • Do not locate the Handheld Printer Terminal and its options on a surface that is unstable or uneven.
Lithium-ion Battery Pack Danger • Never allow the battery pack to become wet. Water can create the danger of battery pack heat emission, explosion, and fire. • Never use or leave the battery pack next to open flame, near a stove, or any other area exposed to high heat. Doing so creates the danger of battery pack heat emission, explosion, and fire. • Never use the battery pack with any device other than the Handheld Printer Terminal.
Safety Precautions Warning • Never place the battery pack in a microwave oven or any other high-voltage device. Doing so creates the danger of battery pack heat emission, explosion, and fire. • Should the battery pack emit a strange odor or heat, change color or shape, or exhibit any other abnormal behavior, immediately stop using it. Continued use creates the danger of battery pack heat emission, explosion, and fire.
AC Power Supply Warning • Do not use the Handheld Printer Terminal at a voltage other than the specified voltage. Also, do not connect the Handheld Printer Terminal to a multi-plug power strip. Doing so creates the danger of fire and electric shock. • Avoid conditions that can cause damage or breaks in the power cord. Do not place heavy objects on the power cord and keep it away from sources of heat. Any of these conditions can damage the power cord, creating the danger of fire and electric shock.
Safety Precautions AC Adaptor Caution • The housing of the AC adaptor can become warm during normal use. • Take normal precautions against electric shock. • At least once a year, unplug the AC adaptor from the wall outlet and clean any dust that builds up between the prongs of the plug. Dust built up between the prongs can lead to the danger of fire. Backup Copies of All Important Data Caution • Note that CASIO Computer Co., Ltd.
Operating Precautions Your Handheld Printer Terminal and its options are precision digital instruments. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. • Do not continue operating the Handheld Printer Terminal when battery power is low. Doing so can cause data to be lost. When the battery goes low, charge it as soon as possible.
Important • The contents of this guide are subject to change without notice. • Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or any third parties for any losses or damages arising from the use of this guide. • Although the utmost care has been taken in preparing this manual, please contact the manufacturer if you should happen to notice any inconsistencies or errors. • This guide does not include any information about programming and download procedures.
Regulatory Information The USA and Canada GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulatory Information L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) I’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Standard EN 300 328 lssue date v1.7.1: 2006.10 and therefore comply with the essential requirements and provisions of the Directive 1999/5/EC of the European Parliament and of the council of March 9, 1999 on Radio equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity and with the provisions of Annex III (Conformity Assessment procedure referred to in article 10).
Contents Safety Precautions ......................................................................................... E-1 Operating Precautions ................................................................................... E-9 Important ....................................................................................................... E-10 Warranty and After Service .............................................................................. E-10 Regulatory Information ...........................
General Guide ................................................................................................... Connecting the AC Adaptor and Connecting to a Computer ............................ Configuring DIP Switch Settings ..................................................................... Connecting Multiple Bridge Satellite Cradles (HA-B61IO) ............................ Bridge Satellite Cradle (HA-B61IO) Specifications ........................................
Before Getting Started Be sure to perform the following steps before trying to use the Handheld Printer Terminal for the first time. 1. When unpacking, make sure that everything is included. Open the box and make sure that all the items shown here are included. Handheld Printer Terminal PC Card Remover (2 pcs) Handheld Printer Terminal n Stylus Neck strap and stylus holder Hand strap Neck strap rings Roll paper Battery pack 58mm Paper Width Adjuster PC card fixers User's Guide (this manual) 2.
3. Load the battery pack into the Handheld Printer Terminal. 1 Turn the battery pack cover lock switch on the side of the Handheld Printer Terminal to the “FREE” position. 2 Open the battery pack cover. 3 Install the battery pack(DT-9723LIC). Push it all way to the end inside the compartment until the eject button at the front of the battery compartment comes up (and sounds). Make sure the battery pack is aligned correctly when you install it.
Before Getting Started 4. Hold down the power key for about one second to turn on the power. Start up the application you want to run. E-18 IT-3000_E_P16_32.p65 18 07.10.
Handheld Printer Terminal System Configuration Options IT-3000 Series Bridge Satellite Cradle HA-B61IO Cradle-type Battery Charger HA-B30CHG Required AC Adaptor for Bridge Satellite Cradle / Cradle-type Battery Charger AD-S42120BE E-19 IT-3000_E_P16_32.p65 19 07.10.
Handheld Priter Terminal System Configuration Battery Pack DT-9723LIC Formed Sheet Paper Holder HA-B93PH Splash Protect Cover HA-B92PCV Screen Protect Cover HA-B90DCV E-20 IT-3000_E_P16_32.p65 20 07.10.
AC Adaptor AD-S10095AE AD-S10095AU * See page 66. E-21 IT-3000_E_P16_32.p65 21 07.10.
Handheld Priter Terminal System Configuration Cables DT-887AXA DT-888RSC DT-380USB HA-B80AX Dsub 9-Pin (Female) RS-232C Cross Cable for Bridge Satellite Cradle RS-422 Modular Cable for connecting Bridge Satellite Cradle USB Cable for connecting Bridge Satellite Cradle and PC RS-232C Cross Cable for connecting Handheld Printer Terminal and PC E-22 IT-3000_E_P16_32.p65 22 07.10.
General Guide IT-3000M53E/M54E2/M55E/M55U/M56E/M56U 3 17 1 2 7 8 24 9 10 4 5 6 23 11 18 12 25 13 14 19 15 20 18 16 22 21 * The C-MOS Imager is only installed on the IT-3000M55E/ M55U/M56E/M56U * Magnetic Card Reader is only installed on the IT-3000M54E2/ M55E/M55U E-23 IT-3000_E_P16_32.p65 23 07.10.
General Guide Slot for inserting SD memory card. This key can be assigned any function available. IT-3000M55E/IT-3000M55U/IT-3000M56E/IT-3000M56U The default settings are as follows. This key is used to read bar codes and 2D code. 1 SD Memory Card Slot 2 Program Key (L) 3 Roll Paper Holder Roll paper is placed in this holder. Use the optional Paper Holder when using a formed sheet paper. 4 Splash Protect Cover and Paper Cutter Printed roll paper is torn off here.
15 Battery Pack Cover Lock Switch Turn this switch when opening and closing the battery pack cover. 16 Battery Pack Cover Houses the battery pack inside. 17 PC Card Slot For connection of a separately sold PC card. Remove the cover to install a PC card. 18 Hand Strap Hook Hook the hand strap here. 19 14-pin Serial Interface Connector Provided for future use. 20 Power Terminals Terminals for supplying power from the Bridge Satellite Cradle and Cradle-type Battery Charger.
General Guide Key Functions 1 Fn Key This key is used to switch the character input mode or make various settings in combination with other keys, or start up a pre-registered application. 2 Numeric Keys These keys are used to input numbers and letters. 3 (Cursor Key) Moves the cursor to the left. 4 (Cursor Key) Moves the cursor to the right. This is also used to feed paper when pressed after pressing the Fn key when printing paper is loaded.
Replacing the Battery Your Handheld Printer Terminal uses two types of battery: a battery pack and a memory backup battery. A battery pack (DT-9723LIC) is used for the main battery. A backup battery is housed inside the Handheld Printer Terminal. This guide uses the following terms to refer to the batteries.
Replacing the Battery To replace the battery pack 1. Make sure that the Handheld Printer Terminal is turned off. If the power is on, press the power key to turn it off. 2. Turn the battery pack cover lock switch on the side of the Handheld Printer Terminal to the “FREE” position. 3. Open the battery pack cover. 4. Remove the battery pack. Press down the battery pack eject button (see the arrow). Remove the battery pack by pulling on the tape. 5.
6. Return the battery pack cover to its original position as shown in the illustration, and then turn the battery pack cover lock switch to the “LOCK” position. Important! • When replacing the battery pack, make sure you do not leave the Handheld Printer Terminal without a battery pack for more than about 10 minutes. Doing so can cause data in the memory to be deleted. • Never try to use other type of battery than the one that is specified for this product. E-29 IT-3000_E_P16_32.p65 29 07.10.
Attaching the Hand Strap A flexible hand strap can be attached to the Handheld Printer Terminal. Hook A Hook B Hand Strap Attach the hand strap following the procedure described below. 1. Attach Hook B of the hand strap to the hand strap hook located on the bottom of the Handheld Printer Terminal. 2. Pull on the hand strap in the direction shown in the illustration, and then fasten Hook A onto hook ( 1 ) on the back of the Handheld Printer Terminal. 1 1 3.
Attaching the Neck Strap A neck strap can be attached to the Handheld Printer Terminal to keep it from being dropped while being carried. The stylus holder provided can also be attached. Neck strap rings* Adjust length here Stylus holder Neck strap Mounting hooks Attach the neck strap following the procedure described below. Attachment Procedure 1. Pull out the neck strap mounting hooks out of each silo on the bottom of the Handheld Printer Terminal using the tip of stylus.
Attaching the Neck Strap Removal Procedure 1. Pull back the locking bar of the neck strap mounting hook and then release the hook from each ring as shown in the illustration. 2. Following the attachment procedure in reverse way, remove the neck strap rings from each neck strap mounting hook on the Handheld Printer Terminal and then push back the neck strap mounting hooks into each silo. Attaching the Stylus Holder The stylus holder provided can be attached to the neck strap as necessary.
2. Remove Mounting Hook C. 3. Pass the stylus holder through the strap as shown in the illustration. 4. Fold back the strap after passing through Bracket C, and then fasten in the same way it was originally fastened with Bracket A and Bracket B. • Do not pass the strap through the stylus holder when folding it back. • Place the stylus in the stylus holder after first re-attaching the neck strap to the Handheld Printer Terminal. Important! • Do not swing the Handheld Printer Terminal with the neck strap.
Configuring Handheld Printer Terminal Settings Calibrating Touch Screen Alignment Whenever you feel that touch screen response is poor or that the operations being executed do not match the location you are tapping on the touch screen, perform the following operations to calibrate the alignment of the touch screen. • Press the “Fn” key and then press the “4” key after confirming that “F” is displayed in the lower right corner of the screen.
Adjusting Display Contrast Perform the following steps to adjust display contrast to make display colors more vivid and easier to see. • Press the “Fn” key and then press the “2” key or “3” key after confirming that “F” is displayed in the lower right corner of the screen. Pressing the “2” key adjusts for more contrast, while pressing the “3” key adjusts for less contrast. * In order to continue to make adjustments, press the “2” key or “3” key after again first pressing the “Fn” key.
Using the Printer The printer can print on roll paper (80 mm or 58 mm wide) or 80 mm wide formed sheet paper. When printing on formed sheet paper, use the paper holder (HA-B93PH) sold separately. When Using Roll Paper Installing the Roll Paper 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key. 2.
5. Close the roll paper holder, slide the lock knobs on the left and right sides as shown in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear off the protruding roll paper. • Please note that the positions of the lock knobs on the left and right sides are different. LOCK FREE 1 2 FREE 2 LOCK 6. Close the splash protect cover as necessary. • Open the splash protect cover when printing with the printer.
Using the Printer Attaching the 58 mm Paper Width Adjuster Attach the 58 mm Paper Width Adjuster inside the roll paper holder when using 58 mm wide roll paper. Refer to the procedure described in “Installing the Roll Paper” for information on opening and closing the roll paper holder. 1. Remove the 80 mm Paper Width Adjuster as shown in the illustration. • Store the 80 mm Paper Width Adjuster in a safe place after it has been removed. 2.
When Using Formed Sheet Paper Attaching the Paper Holder Attach the separately sold Paper Holder (HA-B93PH) when printing on formed sheet paper. The Paper Holder is composed of four parts and four screws. In addition, a PC card cushion is enclosed to prevent the PC card from being dislodged by an impact and so forth. Use this card as necessary. Part C Part B Part A PC card cushion Part D Screws (4) 1. Check that the power is off.
Using the Printer 5. Loosen the two screws shown in the illustration (the screws cannot be removed). 6. Open the cover (PC card slot cover) as shown in the illustration. 7. Loosen and remove the four screws shown in the illustration. Store the removed screws in a safe place so that they do not become lost. 8. Turn the Handheld Printer Terminal back over. 9. Remove the entire roll paper holder. E-40 IT-3000_E_P33_53.p65 40 07.10.
10. Fasten Part A of the Paper Holder to the Handheld Printer Terminal. Press both ends of Part A to fasten to the Handheld Printer Terminal. 11. Insert the projections on both sides of Part into the grooves of Part B and fasten to the Handheld Printer Terminal with the four screws for the Paper Holder. 12.
Using the Printer Loading Formed Sheet Paper Enable the Auto Loading function by selecting Start, Settings, Control Panel and then “Printing Control” of Printer Settings in that order before loading the formed sheet paper. 1. Insert the formed sheet paper all the way into the printer until it stops with the side to be printed facing downward. The paper will be fed into the printer automatically and be positioned at the printing position.
Precautions When Using Printer Printing Accuracy 1. During high-duty printing such as printing horizontal lines or printing while the battery remaining capacity is low, the printing speed may slow down to prevent excess current consumption that may cause unaligned printing for one dot or more. 2. Line change errors may occur if the printing interval between lines is about one second or more.
Using the Printer Others 1. The temperature range for printing with 2-ply paper and label paper is 5 to 35°C. 2. Once the end mark of the paper appears, promptly replace with new paper. 3. Recommended paper: Use only specified papers by CASIO. 4. Paper scraps may accumulate and printing quality may decrease when the printer has been used for a long period of time. The thermal head must be cleaned when this happens.
Using the C-MOS Imager (IT-3000M55E/IT-3000M55U/IT-3000M56E/IT-3000M56U only) 1. Turn on the Handheld Printer Terminal, position its C-MOS Imager reader port near the bar code or 2D code, and then press the Trigger Key (R or L). 2. The Handheld Printer Terminal reads the code by emitting laser and red lights. Indicator 2 (read operation indicator lamp) lights in green when the reading is successful.
Using the C-MOS Imager (IT-3000M55E/IT-3000M55U/IT-3000M56E/IT-3000M56U only) Warning Label IT-3000M55U/M56U Laser light is emitted from this port IT-3000M55E/M56E • This label is a warning label for Class 2 laser products that comply with IEC60825-1+A2:2001 CAUTION • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Magnetic Card Reader The Magnetic Card Reader comes as standard with IT-3000M55E/M55U/M54E2. Only use cards that are compatible with the ISO standards. The procedure for reading cards is described below. 1. Remove the cover as shown in the illustration. 2. Insert the card all the way into the reader as shown in the illustration, and steadily pass the card through the reader in the direction of the arrow.
Performing Data Communication IR Communication IR communication can be used to transfer data between two Handheld Printer Terminals. When performing IR communication, orient the IR ports of both Handheld Printer Terminals so they are pointing directly at each other. Data communication is possible within a distance of 0 (in direct contact) to 1 m (max. 20 cm at 4 Mbps). Important! • A high-sensitivity communication element is used during IR communication.
Bluetooth® Communication Bluetooth® protocol can also be used to transfer data between two Handheld Printer Terminals. The two Handheld Printer Terminals should be no more than five meters apart (as long as there is nothing blocking the path in between). Important! Observe the following precautions to help ensure that data communication is successful. • Make sure that the Handheld Printer Terminal are located within about five meters (16'413⁄16") of each other.
Resetting the Handheld Printer Terminal Resetting the Handheld Printer Terminal is the same as restarting a computer. Performing a reset causes all unsaved inputs and edits to be lost, but data that is already stored in the memory as well as all settings should be unaffected. Use reset to restore normal operation whenever the Handheld Printer Terminal operates abnormally due to misoperation or some other reason. Use the stylus to press the reset switch on the back of the Handheld Printer Terminal.
Performing a Full Reset (Initialization) Performing a full reset initializes memory. This means that all data stored in the memory (RAM) is deleted and all the settings are returned to their initial factory settings. Perform a full reset whenever any one of the following conditions exists. • When you want to delete all memory contents and return the settings to their initial factory settings. • When you are no longer able to use the Handheld Printer Terminal because you forgot your password.
IT-3000 Specifications 1. Terminal Model: IT-3000M53E, IT-3000M55E, IT-3000M55U, IT-3000M54E2, IT-3000M56E, IT-3000M56U CPU: Marvell® PXA255 Application Processor (400 MHz max.) Memory: 64MB RAM, 64MB ROM (user defined: Approx. 30MB) OS: Microsoft® Windows® CE .NET operating system (English Version) Display: 3.5-inch, 240 × 320 dots, 2-Way TFT Color LCD 2.
Character Size: Free double-width characters Generating Method: Black/white inversion, mixed character font printing 8. Card Slot PC Card Slot: PC Card Type I/Type II (3.3 V/5.0 V specifications) * Wake on function available SD Memory Card Slot: SD Memory Card 9. Magnetic Card Reader : ISO 7811 Tracks, 1, 2, and 3 (IT-3000M54E2/M55E/M55U) 10. Power Requirements Main Power: Lithium ion battery pack (DT-9723LIC) Backup Power: Lithium battery (installed inside the terminal) Battery Life: Main battery - Approx.
Using the Bridge Satellite Cradle (HA-B61IO) The optionally available Bridge Satellite Cradle (HA-B61IO) makes it possible to transfer system data and file data between the Handheld Printer Terminal and a computer using an RS-232C interface or USB interface. You can also use the Bridge Satellite Cradle to charge the battery pack installed on the Handheld Printer Terminal. General Guide Top Front Right Back Bottom E-54 IT-3000_E_P54_77.p65 54 07.10.
1 System Status Indicator Lamp This lamp indicates whether the system is operating normally. This lamp indicates the system status and whether or not communication with the system can be performed regardless of whether or not a Handheld Printer Terminal is mounted. Off: System is not operating. Green: System is operating. 2 Communication Indicator Lamp This lamp shows when the Handheld Printer Terminal is performing data communication.
Using the Bridge Satellite Cradle (HA-B61IO) Connecting the AC Adaptor and Connecting to a Computer Use the AC adaptor available as an option for the Bridge Satellite Cradle to supply the power to it. Always make sure that the power is being supplied to the Bridge Satellite Cradle by the AC adaptor before performing any type of data communication operation with the Handheld Printer Terminal. The Handheld Printer Terminal draws the power via the Bridge Satellite Cradle during data communication. 1.
4. Turn on the power. This causes the Bridge Satellite Cradle power indicator lamp to light red. 5. Place the Handheld Printer Terminal so that the infrared communication unit on the right side is faced firmly with the infrared communication unit of the Bridge Satellite Cradle. • If the system is operating normally and data communication is enabled, the system status indicator lamp lights green. • The communication indicator lamp flashes green when data communication starts.
Using the Bridge Satellite Cradle (HA-B61IO) Configuring DIP Switch Settings Removing the bottom cover of the Bridge Satellite Cradle exposes the DIP switches. You can change the ON/OFF settings of the DIP switches to set the configuration. Only set the DIP switches after first switching OFF the power.
Connecting Multiple Bridge Satellite Cradles (HA-B61IO) Connect “C-OUT” of the Bridge Satellite Cradle connected to the host computer to “C-IN” of the next Bridge Satellite Cradle you want to connect. RS-232C cable or USB cable To host computer RS-422 modular cables (DT-888RSC) Important! You can use the optional RS-422 modular cables (DT-888RSC) to link up to eight Bridge Satellite Cradles. E-59 IT-3000_E_P54_77.p65 59 07.10.
Using the Bridge Satellite Cradle (HA-B61IO) Bridge Satellite Cradle (HA-B61IO) Specifications 1. IR Data Communication Interface: Protocol: Synchronization: Transfer Rate: 2. USB Protocol: Transfer Rate: 3. RS-232C Protocol: Synchronization: Transfer Rate: 4. RS-422 Protocol: Synchronization: Transfer Rate: 5. Charging Charging System: Charge Time: 6. Power Supply Power Requirement: Power Consumption: Output to Handheld Printer Terminal: 7. AC Adaptor Model: Input: Output: 8.
Using the Cradle-type Battery Charger (HA-B30CHG) The optionally available Cradle-type Battery Charger (HA-B30CHG) lets you charge the Handheld Printer Terminal’s battery simply by placing the Handheld Printer Terminal onto the charger. General Guide Top Front Right Back Bottom E-61 IT-3000_E_P54_77.p65 61 07.10.
Using the Cradle-type Battery Charger (HA-B30CHG) 1 Power Indicator Lamp This lamp indicates the power status and the mounting status of the Handheld Printer Terminal. Off: Power off Red: Power on, Handheld Printer Terminal not mounted Green: Power on, Handheld Printer Terminal mounted correctly 2 Terminal Detect Switches These switches detect when the Handled Printer Terminal is seated correctly on the Cradle. 3 Power Contacts Power is supplied to the Handheld Printer Terminal via these contacts.
Connecting the AC Adaptor for the Cradle-type Battery Charger Use the dedicated AC adaptor for the Cradle-type Battery Charger to connect to a wall outlet. 1. After making sure that the Cradle-type Battery Charger power switch is turned off, plug the AC adaptor into the AC adaptor jack on the back of the charger. Power switch (OFF) 2. Next, after connecting the power cable to the AC adaptor, plug the AC adaptor into a power outlet. 3. Turn on the power.
Using the Cradle-type Battery Charger (HA-B30CHG) Cradle-type Battery Charger (HA-B30CHG) Specifications 1. Charging Charging System: Charge Time: 2. Power Supply Power Requirement: Power Consumption: Output to Handheld Printer Terminal: 3. AC Adaptor Model: Input: Output: 4. Dimensions and Weight Dimensions: Weight: 5. Operating Environment Temperature: Humidity: Fixed-voltage (with current limiter) Approximately 8.0 hours AC adaptor (AD-S42120BE*) 12V DC, approximately 2,100mA 10V DC 1,800mA (max.
Using the AC Adaptor (AD-S10095AE/AU) 1. Turn off the power of the Handheld Printer Terminal by pressing the power key. 2. Open the jack cover ( 1 ), and then insert the plug of the AC Adapter into the charging jack ( 2 ). After connecting the power cable to the AC adaptor, plug the other end of it into an electrical outlet. 1 2 3. Charging begins and Indicator 1 on the Handheld Printer Terminal lights red. Charging is completed when Indicator 1 changes to green.
Using the AC Adaptor (AD-S10095AE/AU) Specifications 1. Charging Specification Charging Method: Charge Period: 2. AC Adaptor Model: Input: Output: 3. Dimensions and Weight Dimensions: Weight: 4. Operating Environment Temperature: Humidity: Constant current/voltage Approx. 8 hours (with the power off) AD-S10095A 100V to 240V AC 50/60 Hz 0.4A 9.5V DC 1A 9.5W Approximately 78(W) × 50(D) × 30(H) mm (31⁄16"W × 115⁄16"D × 13⁄16"H) Approximately 130g (4.
Using PC Cards PC card compatible with the PCMIA(Type I/II) standard can be installed in the PC Card slot on the Handheld Printer Terminal. Insert a PC card according to the procedure described below. Attachment of PC Card Removal Tape to a PC Card There are some PC cards that may be difficult to remove from the PC card slot once they have been inserted. In the case of such PC cards, attach the PC card removal tape provided before inserting the PC card.
Using PC Cards 4. Open the cover (PC card slot cover) as shown in the illustration. 5. Insert a PC card having PC card removal tape attached. Insert the PC card all the way in with the top of the card facing towards the top of the Handheld Printer Terminal. Fold up the end of the PC card removal tape so that it does not get caught in the way when closing the cover. 6. Attach the PC Card Holder to lock the end of the PC card and prevent it from coming out due to impacts and so forth.
Removing a PC Card Press the eject button on the left side of PC card slot with the stylus as shown by the arrow, and pull out the PC card while holding onto the end of the PC card removal tape. Inserting a PC Card (When Using the Paper Holder) Check the names of the parts of the Paper Holder before beginning work. Part C Part B Part A PC card cushion Part D Screws (4) 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key. 2.
Using PC Cards 3. After pushing on both ends of Part A and reattaching to the Handheld Printer Terminal ( 1 ), remove Part B by removing the screws ( 2 ). 1 2 4. Insert a PC card to which PC card removal tape has been attached. Insert the PC card all the way in so that the top of the PC card faces the top of the Handheld Printer Terminal. (The illustration shows the Handheld Printer Terminal turned over.
7. While spreading apart both ends of Part A ( 1 ), remove Part A from the Handheld Printer Terminal by lifting up Part A until the projections reach the upper edges of the grooves of Part B ( 2 ), and then press on Part C and Part D from the left and right sides ( 3 ). Next, push on both ends of Part A to fasten to the Handheld Printer Terminal.
Using SD Memory Cards SD memory card can be installed in the SD Memory Card slot on the Handheld Printer Terminal. Insert (or remove) an SD memory card according to the procedure described below. Inserting an SD Memory Card 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key. 2.
Connecting a Bar Code Reader (IT-3000M53E/IT-3000M54E2 only) Connect a bar code reader to the RS-232C interface connector (8-Pin) on the Handheld Printer Terminal. Connecting the bar code reader 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key. Open the cover of the RS-232C interface connector. ( 1 ) 2. Insert the plug of the bar code reader into the connector as shown in the illustration.
Attaching the Screen Protect Cover Attaching the Screen Protect Cover to the Handheld Printer Terminal prevents the screen from being cracked or damaged when carrying. 1. Remove the two screws on the right side of the Handheld Printer Terminal. Store the screws in a safe place after they have been removed. 2. Fasten the Screen Protect Cover with the two screws provided with the Screen Protect Cover. 3. Close the Screen Protect Cover and fasten by pressing on the cover hook at the right side. 4.
Attaching the Splash Protect Cover Attaching the Splash Protect Cover to the Handheld Printer Terminal lets you use it even during inclement weather. inner cover Attach the Splash Protect Cover by following the procedure described below. 1. Press the ridged ( ) portions ( 1 ) of the paper outlet cover while spreading apart the locks on the left and right sides ( 2 ) to disengage them as shown in the illustration followed by opening the paper outlet cover ( 3 ). 2.
Attaching the Splash Protect Cover 5. Close the roll paper holder, slide the lock knobs on the left and right sides as shown in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear off the protruding roll paper. • Please note that the positions of the lock knobs on the left and right sides are different. LOCK FREE 1 2 FREE 2 LOCK 6.
Using the Battery Pack Important! • Make sure to attach the contact cover provided when removing the Battery Pack from the Handheld Printer Terminal and storing. • If the battery pack has been left over unused for a long period of time, the capacity remained decreases due to spontaneous discharge or chemical decomposition by the battery pack itself. If the battery pack fails to hold its operating duration after it has been fully charged, replace it with a new one.
