User Manual

Operation Guide 5423
E-39
To change the current date setting manually
1. In the Timekeeping Mode, keep A depressed (for
about fi ve seconds) as the
x
Second Hand goes
through the following sequence.
x Moves to Y (or YES for some models) or N (NO)
to indicate the last signal reception result, then to
R (READY), and then to the city code of the currently
selected Home City.
2. Press C twice so the
n
Right Dial Hand moves to the
tens digit and the
x
Second Hand moves to the ones
digit of the current year setting.
x This is the year setting mode.
x The year can be set in the range of 2000 to 2099.
3. Use D and B to change the year setting.
x Each press of B will move the
n
Right Dial Hand and change the tens digit of
the year setting.
n
00
10
20
30
40
50
60
70
80
90
Setting the year (tens digit)
E-38
4. Use D (+) and B (–) to change the time (hour and minute) setting.
x Each press of either button will move the hands (
z
Hour Hand and
c
Minute
Hand) one minute.
x Holding down D or B will start high-speed
z
Hour Hand and
c
Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
x The
v
24-hour Hand and
z
Hour Hand move in sync with each other.
x When setting the time, make sure that the
v
24-hour Hand indicates the proper
a.m./p.m. hour.
x If you want to change the date setting at this time, press C and perform the
procedure starting from step 3 under “To change the current date setting
manually” (page E-39).
5. After the time setting is the way you want, press A to return to the Timekeeping
Mode.
x This will cause the
x
Second Hand to move automatically to 12 o’clock and
resume movement from there.
E-37
2. Change the Home City and daylight saving time (DST)
settings, if you want.
x For details about these settings, see steps 2 and 3
under “To confi
gure Home City settings” (page E-32).
x In the following steps, each press of C cycles
between settings as shown below.
Home city/DST Hour/Minute Year
Day Month
C
C
C
C
C
3. Press C.
x The
x
Second Hand and
n
Right Dial Hand will move to their 12 o’clock
positions. This is the time setting mode.
30
n
v
z x c
E-36
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable
to receive a time calibration signal.
To change the current time setting manually
1. In the Timekeeping Mode, keep A depressed (for about
fi ve seconds) as the
x
Second Hand goes through the
following sequence.
x Moves to Y (or YES for some models) or N (NO)
to indicate the last signal reception result, then to
R (READY), and then to the city code of the currently
selected Home City.
x At this time, the
n
Right Dial Hand will indicate the
Home City’s current daylight saving time setting (STD
or DST).
30
nx
E-35
x In the city code setting mode, the
n
Right Dial Hand indicates the current
daylight saving time setting as STD (standard time) or DST (daylight saving
time).
x Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
3. After the setting is the way you want, press A to return to the Timekeeping Mode.
Note
x After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time
in your Home City.
x Selecting some city codes makes it possible for the watch to receive the time
calibration signal for the corresponding area automatically. See page E-16 for details.
* Coordinated Universal Time, the world-wide scientifi
c standard of timekeeping. The
reference point for UTC is Greenwich, England.
E-34
x In the city code setting mode, the
n
Right Dial Hand indicates the current
daylight saving time setting as STD (standard time) or DST (daylight saving
time).
x Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
4. After all the settings are the way you want, press A to return to the Timekeeping
Mode.
To toggle the Home City time between standard time and daylight saving time
1. Perform the step 1 under “To confi
gure Home City settings” on page E-32.
x Each time you select a city code, the
z
Hour Hand,
c
Minute Hand, and
v
24-
hour Hand move to the current time for that city code. Do not perform the next
operation until these hands stop moving.
2. Press B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
E-33
x The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
x For details about city codes, see the “City Code
Table” at the back of this manual.
2. To change the Home City setting, press D to move the
x
Second Hand clockwise.
x Keep pressing D until the
x
Second Hand is pointing
at the city code you want to select as your Home City.
x Each time you select a city code, the
z
Hour Hand,
c
Minute Hand,
v
24-hour Hand and
m
Day
Indicator move to the current time and date for that
city code. Do not perform the next operation until
these hands stop moving.
3. Press B to toggle the time for the currently selected city code between STD
(standard time)/DST (daylight saving time).
30
x
z c
nv m
E-32
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To confi gure Home City settings
Note
x This watch does not have a city code that
corresponds to Newfoundland.
1. In the Timekeeping Mode, keep A depressed (for
about fi
ve seconds) as the
x
Second Hand goes
through the following sequence.
x Moves to Y (or YES for some models) or N (NO)
to indicate the last signal reception result, then
to R (READY), and then to the city code of the
currently selected Home City.
x This indicates the city code setting mode.
30
x
E-31
Timekeeping
Use the Timekeeping Mode to view the current time and date. To enter the
Timekeeping Mode from any other mode, hold down C for about two seconds.
Hand Functions
z
Hour Hand
x
Second Hand
c
Minute Hand
v
24-hour Hand
b
Left Dial Hands: Indicate the current time in the World
Time City (page E-46) in 24-hour format.
n
Right Dial Hand: Indicates the day of the week.
m
Day Indicator
30
z cx
b nv m
E-30
To select a mode
Press C to cycle between the modes as shown below. The
n
Right Dial Hand
indicates the currently selected mode.
n
Timekeeping Mode Stopwatch Mode
World Time Mode
The hand indicates the
day of the week (SU,
M, T, W, T, F, S).
The hand points to 0 (at
12 o’clock).
The hand points to STD
or DST.
C