EN . WSD-F10 WSD-F20 WSD-F20S User’s Guide Thank you for purchasing this watch. Before trying to use this watch, be sure to read the Safety Precautions in the Quick Start Guide that comes with it. Make sure you use the watch correctly. © 2017 CASIO COMPUTER CO., LTD.
Contents Introduction ....................................................................................... EN-2 Watch Features ............................................................................ EN-2 Measurement Functions ............................................................... EN-4 Overview ...................................................................................... EN-6 About This Manual .......................................................................
Introduction Attention WSD-F10 Owners! ● This manual describes operations for a WSD-F10 watch that has been updated to Android Wear TM 2.0. For information about updating to Android Wear 2.0, visit the website below. https://support.google.com/androidwear/ ● The functions below, which are described in this manual, are not supported by the WSD-F10.
Five-atmosphere Water Resistance + MIL-STD* Even though this watch has a built-in voice recognition microphone, it still is water resistant up to five atmospheres. This means you can wear your watch while swimming, fishing, etc. MIL-STD-810G standard environment resistance allows you to wear your watch while engaged in a variety of vigorous outdoor activities, including: mountain climbing, cycle sports, fishing, and more.
CASIO MOMENT SETTER+ App for Smartphone Control of the Watch A CASIO MOMENT SETTER+ smartphone app (available from the Google Play ™ store for Android smartphones only) can be used to customize the watch setup (MOMENT SETTER notifications, TOOL app functions, etc.) from your smartphone. CASIO Camera Linking Use this app to control supported CASIO camera models from the watch. For details, visit the CASIO website below. http://support.casio.
Altimeter, Barometer The watch’s Altimeter uses a pressure sensor to measure barometric pressure, and then calculates and displays relative altitude based on the measured value. Because of this, readings taken at different times at the same location may produce different altitude values due to changes in temperature, humidity, barometric pressure, and other factors. Also note that values displayed by the watch may be different from elevations indicated for areas where you are located.
Overview Package Contents Watch, AC adaptor, charger cable, Quick Start Guide, warranty General Guide ① ② ⑤ ③ ⑥ ⑦ ④ ⑧ A Charge LED E TOOL button B Charger terminal F Power button C Pressure sensor G APP button D Microphone H Touch screen EN-6
About This Manual The contents of this manual are subject to change without notice. Copying of this manual, either in part or its entirety, is forbidden. You are allowed to use this manual for your own personal use. Any other use is forbidden without the permission of CASIO COMPUTER CO., LTD. ● CASIO COMPUTER CO., LTD. shall not be held liable for any lost profits or claims from third parties arising out of the use of this product or this manual. ● CASIO COMPUTER CO., LTD.
Getting Ready Be sure to read the precautions in the “Quick Start Guide”, and also perform all of the steps under “Preparing the Watch for First Use” and “Preparing the Watch for Outdoor Use”. Preparing the Watch for First Use You must perform the steps below before using the watch for the first time. 1. Charge the watch Plug the provided AC adaptor into a power outlet, and then connect the provided charger cable and AC adaptor as shown in the illustration.
3. Pair the Watch with Your Smartphone When pairing, it is recommended that you have the smartphone and watch within one meter of each other. Refer to the websites below for information about how to pair the watch with a smartphone. Android Wear Help https://support.google.com/androidwear/ CASIO website http://support.casio.com/wsd/ 4.
Preparing the Watch for Outdoor Use Performing the steps below prepares the watch’s outdoor functions (CASIO watch faces and apps) for optimal operation. Perform these steps after you have completed the procedure under “Preparing the Watch for First Use”. 1. Configure watch settings to enable use of Play Store. 1. If you are using the watch while it is connected with an iPhone, connect the iPhone to Wi-Fi. 2. While a watch face is displayed, short press the power button to display the App menu. 3.
Watch Operation (WSD-F20/WSD-F20S) 1. While the watch face is displayed, swipe the touch screen from top to bottom and then tap D. 2. Scroll downwards and tap “Connectivity” and then “Location”. 3. On the screen that appears, enable “Location”. Watch Operation (WSD-F10) 1. While the watch face is displayed, swipe the touch screen from top to bottom and then tap D. 2. Scroll the screen downwards, and then tap “Connectivity”. 3. Scroll the screen downwards until “Location” appears, and then turn it on.
5. Turn on the “Save daily activity records” setting. 1. While the watch face (Authentic, Field, Multi) is displayed, hold your finger on the touch screen for about two seconds. This displays the setting menu. 2. Scroll the setting menu downwards. When “Save daily activity records” is displayed, check to make sure that its setting is “OFF”. Next, tap the setting. ● A dialog box will appear to confirm if you want to save activity records. Carefully read the text of the dialog box. 3. Tap “I agree.”.
Basic Operations You Should Remember ● Important! Note that the operations described here are subject to change due to the type and version of the operating system being used by the smartphone connected with the watch, changes that occur when the watch’s operating system is updated, and other factors. For details about Android Wear operations, visit the website below. https://support.google.com/androidwear/ Button Functions Power button Press to restore display brightness after it goes dark.
Wake Up If you don’t tap the touch screen for a few seconds, the watch screen will dim. To wake up the watch and restore it to normal brightness, tap the touch screen or press the power button. Power Supply Operations To do this: Charge the watch Turn off power Turn on power Perform this operation: See step 1 under “Preparing the Watch for First Use”. 1. While the watch face is displayed, swipe the touch screen from top to bottom and then tap D. 2. Scroll the screen downwards.
Watch Face Operations To do this: Switch to another watch face Perform this operation: 1. While a watch face is displayed, swipe the touch screen slightly left or right to display a list of favorite watch faces. 2. Scroll a list of favorite watch faces left and right. When the watch face you want to use is displayed, tap it. Add a watch face to favorites 1. Scroll a list of favorite watch faces as far as it will go to the right and then tap “Add more watch faces”. This displays a list of all watch faces.
Using Apps To do this: Start up an app Perform this operation: 1. While a watch face is displayed, short press the power button to display the App menu. 2. Scroll the list of apps upwards or downwards. When the app you want to run is displayed, tap it. Return to the watch face Press the power button.
Android Wear Functions The Android Wear operating system of this watch provides the functions below as standard. ● Dictation and voice command operation ● Messaging and incoming phone call notification ● Timer, Agenda, Translate, and other standard Android Wear apps Watch faces and apps can be added using the Play Store app* Android Wear Settings * Your watch comes with a built-in Play Store app that you can use to add watch faces and apps using watch operations only (without a smartphone).
Using Outdoor Watch Functions - Using CASIO Watch Faces and Apps This section explains how to interpret the contents of CASIO watch faces and how to use CASIO apps and make your outdoor adventures more interesting and enjoyable. Use this app: Location Memory (WSD-F20/WSDF20S only) TOOL Activity MOMENT SETTER Timepiece To do this: Check your current location on a color map. Find out more about the natural environment around you. Keep track of current information about your activities.
Using CASIO Watch Faces Your watch comes with the CASIO Watch Faces described below built in. Watch face names are used in the list of favorite watch faces and the list of all watch faces (see “Watch Face Operations”). Location *1 Traveler *1 2 Layers Authentic World Time Altitude Field Multi Combination Analog watch face that shows your current latitude and longitude based on the watch’s GPS, along with a background image of a world map centered on your current location.
● Important! Whenever the watch’s battery charge level is less than 5%, the watch will automatically switch to the monochrome LCD watch face when screen illumination dims after the prescribed period of non-use. To switch to the original watch face, tap the touch screen. If the message “Perform magnetization correction.” appears... The “Perform magnetization correction.” notification may appear while you are using a watch face that includes a compass.
Using the Location Memory App (WSD-F20/WSDF20S only) The Location Memory app makes it quick and easy to record map-related information. You can use the Location Memory app to perform the operations described below. ● Display a map to check your current location. ● Select from a variety of different map skins including street view, geographic view, satellite view, and more. ● While the app is running, you can track your route on the map. ● Use dictation to create a text memo about your current location.
Location Memory App Basic Operations You can perform main Location Memory app operations using the TOOL button and APP button. The operations you can perform with these two buttons are indicated by on-screen icons displayed to the left of each button. You can also perform the operations by tapping the icons. Icon Pressing the button or tapping the icon does this: Changes the functions of the two buttons to zoom in and zoom out (see below).
Other Operations To view a recorded memo, swipe the displayed map from bottom to top. On the menu that appears, tap “History”. For information about how to track your route on a map, see “Enabling Route Tracking on the Map (Route Display)”. ● For information about map display settings, see “Common Outdoor Function Settings” and perform one or more of the operations below.
To display your route, use the procedure below to change “Route Display” on the setting menu from “OFF” (initial default setting) to “ON”. 1. While the map is displayed, swipe the touch screen from bottom to top. On the menu that appears, tap “Settings”. 2. Scroll the setting menu downwards. After confirming that the “Route Display” setting is “OFF”, tap to change it to “ON”. Important! This watch acquires location information at regular intervals and tracks your route on a map.
Changing the “Revisit” Mark Notification Setting Use “Revisit” marks to record a mark and have the watch alert you whenever you are in the vicinity. Under the watch’s initial default settings, notification is performed when both of the conditions below are satisfied. ● You are <> of the “Revisit” mark location. ● <> has passed since you were last <> of the “Revisit” mark location.
Using the TOOL App The TOOL app displays a wide variety of information about the natural environment around the watch. TOOL Function List Compass Altimeter Barometer Sunrise/sunset Tide Graph My Graph Shows a compass needle on the face. Two color screens are available. An Altimeter Screen (A) that shows a value and dial indication of the altitude at your current location, and an Altitude Graph Screen (B) that shows a graph of altitude changes over the past 24 hours. Two color screens are available.
Basic TOOL Operations To do this: Change the TOOL function Switch between the two color screens (A and B) (See “TOOL Function List”.) Change TOOL app settings Perform this operation: While the TOOL app is running, press the TOOL button. ● While the TOOL app is running, swipe the touch screen from top to bottom, or from bottom to top. To switch from screen A to screen B, swipe the touch screen from right to left. To switch from screen B to screen A, swipe the touch screen from left to right.
Using Compass The pointer indicates true north.*1 The value in the center of the display shows how many degrees there are in a clockwise direction from the north indication (which is 0°) to 12 o’clock on the watch. For example, if 12 o’clock on the watch is facing due east, the value will show 90°. Letters on the display also indicate the direction that 12 o’clock is facing (16 directions). *1 Initial default setting.
Using Altimeter Altimeter has a color display Altimeter Screen (left), a color display Altitude Graph Screen (center), and a monochrome display (right). All of the screens show the altitude at your current location. The Altitude Graph Screen shows a graph of altitude changes over the past 24 hours, along with the low altitude (Min) and high altitude (Max) during that period. ● The upper part of the monochrome display shows a graph of altitude changes over the past 23 hours.
Before Using Altimeter The watch’s Altimeter can be configured to use positioning information (GPS) to correct altitude readings automatically (not supported when the WSD-F10 is connected with an iPhone). Configure the settings below to use this function. ー Correctly configure the “Location” setting on the watch and smartphone. For more information, see step 1 under “Preparing the Watch for Outdoor Use”. ー Select “ON” for the “Correct Altitude Using Location” setting.
Altimeter Precautions Do not use this watch while skydiving, hang gliding, paragliding, gyrocopter flying, glider flying, or engaged in other activities where altitude changes suddenly. ● Altitude readings produced by this watch are not intended for specialpurpose or industrial level use. ● In an aircraft, the watch measures the in-cabin pressurized air pressure, so readings will not match altitudes announced by the crew.
Using Barometer Barometer has a color display Barometer Screen (left), a color display Barometric Pressure Graph Screen (center), and a monochrome display (right). All of the screens show the barometric pressure at your current location. The Barometric Pressure Graph Screen shows a graph of pressure changes over the past 24 hours, along with the low pressure (Min) and high pressure (Max) during that period.
Using Sunrise/Sunset Sunrise/Sunset has a color display Time Screen (left), a color display Azimuth Screen (center), and a monochrome display (right). The Time Screen shows the following times: sunrise time (upper left), predawn nautical twilight start time (lower left), sunset time (upper right), postsunset nautical twilight end time (lower right), and the current time (bottom center). ● The Azimuth Screen shows the current time, the sunrise time, and the sunset time.
Using Tide Graph Tide Graph a color display Tide Graph Screen (left), a color display Fishing Time Screen (center), and a monochrome display (right). The Tide Graph Screen shows the current tide level and time (red characters in the center of the screen), along with the high tide (High) and the low tide (Low) that will occur up to 12 hours later. The graph shows changes in the tide level for 24 hours (12 hours before and after the current time).
Using My Graph My Graph shows the status of your activities for the current day. Under initial default settings, both screens show how many calories you have burned from the start (00:00) of the current day. ● A color display shows what types of activities you have performed on the current day as a concentric circle graph. Values at the bottom of the screen show the cumulative times spent engaged in each type of activity ( : ● Riding, ● : Resting, : Walking, : Running).
To specify the type of values shown in the center of the My Graph screen 1. Swipe the touch screen from right to left. On the “Settings” Screen that appears, tap D. This displays the setting menu. 2. Scroll the setting menu upwards and downwards. When “Centered value / My Graph” is displayed, tap it. This displays a list of value types. 3. Scroll the list upwards and downwards. When the type of value you want shown in the center of the My Graph Screen is displayed, tap it.
Using the Activity App The Activity app shows cumulative elapsed time from when one of the outdoor activities listed below starts until it stops, a track of the route followed on a map, and a list of data (activity time, tracked route, etc.) Trekking Fishing Cycling *2 Paddle *1 Snow *1 *1 WSD-F20/WSD-F20S only *2 Available with the WSD-F10 only while the watch is connected with an Android phone.
Basic Activity App Operations To do this: Start measurement (excluding Snow*3) Start a Snow*3 measurement operation (while “Auto Record” is “ON”) Start a Snow*3 measurement operation (while “Auto Record” is “OFF”) Stop a measurement operation*4 Input fishing results during Fishing measurement Perform this operation: Select the type of activity whose data you want to measure and then tap “START”. Select the type of activity whose data you want to measure and then tap “BEGIN”.
MOMENT SETTER Notification Function On the “START” Screen, you can tap to display a screen for configuring MOMENT SETTER settings that control how notifications of useful information are provided to you while engaging in an activity. For details, see “Using the MOMENT SETTER App”. Data Displayed During Measurement Operations Note the points below concerning the data displayed while a measurement operation is in progress.
Using the MOMENT SETTER App For example, you can use the MOMENT SETTER app to receive notifications like the ones shown below. ● During an Activity app Trekking measurement operation, perform a vibration notification and display the remaining altitude when there are 200 m remaining to an altitude of 2000 m. ● Every day, perform vibration notification and display the sunrise time one hour before sunrise. Operation involves simple selection of the notification to be received from a menu.
MOMENT SETTER App Main Menu Starting up the MOMENT SETTER app first displays a Main Menu. Setting items included in the Main Menu are shown in the table below. Tapping this item: Recent Climbing, trekking*1, Fishing*1, Cycling*1, Paddle*1*2, Snow*1*2 Extras Settings Displays this menu: Menu of up to three notifications that were last turned on. This item appears when one or more MOMENT SETTER notifications were turned on.
Example MOMENT SETTER Operation This section shows an example operation for configuring notification settings for “Climbing, trekking”. This operation can be started from the MOMENT SETTER app or Activity app. 1. Start up the MOMENT SETTER app and scroll the main menu upwards and downwards. When “Climbing, trekking” is displayed, tap it. Or, on the Activity app “Trekking” “START” Screen, tap . 2.
5. At the bottom of the display, tap to toggle it to . 6. Press the power button to exit the MOMENT SETTER app. ● After performing the above operation, you need to start up the Activity app and start a Trekking measurement operation to actually receive notifications. See “Using the Activity App”. Note ● A notification from MOMENT SETTER is deleted automatically after a fixed amount of time.
Timepiece Mode Operations To do this: Switch the watch to Timepiece Mode Perform this operation: 1. Start up the Timepiece app (see “Start up an app”). ● This displays a confirmation screen. 2. Read the explanation on the screen, swiping from right to left as required to change pages. 3. Swipe the touch screen from left to right to return to the confirmation screen. 4. Tap .
Common Outdoor Function Settings CASIO apps and CASIO watch faces share the same outdoor functions such as Compass, Altimeter, etc. This section explains settings that are common to all CASIO apps and watch faces. Basic Operations for Configuring Common Settings Use the setting menu to configure common settings. The required operation to display the setting menu depends on what screen is displayed, but operations are the same in all cases once the menu is displayed.
Setting Item List The setting items displayed on the setting menu (see “Basic Operations for Configuring Common Settings”) are shown below. After displaying the setting menu, perform the operation required for the item whose setting you want to change. Note ● The letters to the right of each setting item indicate the screen from which the setting item can be displayed. For example, the letters “WF” to the right of a setting item means that the setting item can be displayed from a watch face (WF) screen.
Altitude Calibration (WF/TL/AC) Operation 1. If “Correct Altitude Using Location” is on, turn it off. 2. Tap “Altitude Calibration”. 3. On the altitude input screen that appears, input the elevation at your current location (which you obtained from local indications). ● Tap the digit of the value that you want to change, and then use and to change it. ● To reset a manually input altitude calibration value, tap C.
Correct Altitude Using Location (WF/TL/AC) Operation Each tap of this setting item toggles between “ON” and “OFF”. Description Select “ON” for this setting to perform auto altitude calibration based on the watch’s or your smartphone’s location information (GPS). “OFF” must be selected for this setting to perform altitude calibration manually using “Altitude Calibration”. Important! This setting is not available while there is a connection between the WSDF10 and your iPhone.
Description Though the pressure sensor built into the watch is adjusted at the factory and normally does not require calibration, you can perform the calibration operation above if you notice that readings are very different from those from other sources. To calibrate manually, use this item to input the current barometric pressure as measured by another accurate barometer. Centered value / My Graph (TL) Operation Tap this setting item and then scroll the list that appears upwards and downwards.
Monochrome Display (WF/TP) Operation Each tap of this setting item toggles the face background between “Dark” and “Bright”. Description You can select how the watch’s monochrome LCD displays data. This setting is applied to all of the displays below. ● “2 Layers” watch face monochrome display ● TOOL app monochrome display ● Timepiece Mode monochrome display GPS Time Calibration (WSD-F20/WSD-F20S only) (WF) Operation 1. Move to an outdoor area where the sky is visible. 2.
Port setting (TL) Operation Tap this setting item and then scroll the list that appears upwards and downwards. When the name of the point (port name or name of a city near the ocean) you want is displayed, tap it. Description This setting specifies the point (port) whose tide information is displayed by the “Tide Graph” of the TOOL app. Re-calculation with Current Location (TL) Operation Tap this setting item to start acquisition of positioning information for your current location.
Save Daily Location Info (WSD-F20/WSD-F20S only) (WF/MS/LM) Operation After tapping this setting, you then need to select “Every 6 minutes”, “Every 1 minute”, or “OFF”. ● Important! When you tap this setting item to toggle from “OFF” to “ON”, you will also need to tap “Every 6 minutes” or “Every 1 minute” on the confirmation dialog box that appears. Description This item is for configuring a setting related to the Location Memory app.
Save daily activity records (WF/TL/MS) Operation Each tap of this setting item toggles between “ON” and “OFF” (initial default setting). ● Important! When you tap this setting item to toggle from “OFF” to “ON”, you will also need to tap “I agree.” on the confirmation dialog box that appears. Description This item is for configuring a setting related to watch faces (Authentic, Field, Multi), the TOOL app (My Graph), and the MOMENT SETTER app.
Wrist where you wear the watch (TL/MS) Operation Each tap of this setting item toggles between “Right” and “Left”. Description The value you input for this item is used as basic information when calculating data displayed on the TOOL app’s “My Graph”. Target altitude (AC) Operation Tap this setting item and then use the screen that appears to specify a target altitude. ● Tap the digit of the value that you want to change, and then use and to change it.
Auto Record (WSD-F20/WSD-F20S only) (AC) Operation 1. Use the Activity app to display the Snow “BEGIN” screen, and then tap “BEGIN”. 2. Swipe the touch screen from right to left as many times as necessary to display the “Settings” Screen. Next, tap D. 3. On the setting menu that appears, swipe upwards and downwards until “Auto Record” is displayed, and then tap it. ● Each tap toggles between “ON” and “OFF”.
Description This item is for selecting the map skin displayed by the Activity app and the Location Memory app. You can select geographic view, satellite view, or another view to suit your location or purpose. Download Map (AC/MS/LM) Operation 1. Change the “Map Type” setting to “Mapbox”. 2. Tap “Download Map”. ● This displays a list of map skin names. 3. Scroll the list upwards and downwards. When the skin name you want is displayed, tap it. ● This displays a map with your current location in the center.
Description This item is for configuring settings related to the Activity app and the Location Memory app. It is for downloading a map to watch memory when “Mapbox” is selected for “Map Type”. If you want to use the map in an area where a network connection is not available, use this item beforehand in an area where a network connection is available to download the desired map. Downloaded Map (AC/MS/LM) Operation Tapping this setting displays the map you downloaded.
All Off (MS) Operation 1. Tap this item and a confirmation dialog box will appear asking if you want to disable all MOMENT SETTER notifications. 2. Tap “Turn off.” to disable notifications or “Cancel” to leave notifications enabled. Description Removing all check marks from the MOMENT SETTER app menu disables all notifications. Note that once you perform this operation, there is no single batch operation to re-enable notifications.
Monochrome Display Your watch has a dual-layer color and monochrome LCD. This section summarizes when the monochrome display is displayed. Watch Monochrome Displays Your watch has the two types of monochrome display screens shown below. (Lined) (Unlined) The watch displays the monochrome display in the cases below. After entering Timepiece Mode The lined screen shown in ① will be displayed. See “Using the Timepiece App”.
While the “ 2 Layers ” watch face is selected If you do not perform any operation on the watch, the unlined screen shown in ② will be displayed. Tapping the touch screen will switch to the color display. While “Always-on screen” is OFF If you do not perform any operation on the watch, the unlined screen shown in ② will be displayed. Tapping the touch screen will switch to the color display. “Always-on screen” is an Android Wear setting item. For details, visit the website below. https://support.google.
Troubleshooting Refer to this section whenever you are experiencing problems with watch operation. If you don’t find the solution to your problem here, visit the website below. http://support.casio.com/wsd/ Restoring Watch Operation If you find yourself unable to obtain proper operation from the watch for some reason, restart it and then try performing the operation again. For information about restarting the watch, visit the website below. https://support.google.
1021 Sensor problem. Correct readings are not possible. Frequent appearance of this message could indicate malfunction. 9000 Some problem occurred with the watch. Power will turn off shortly. 9001, 9002, 9003 Some problem occurred with the watch. Power will turn off shortly. 9010 Watch temperature is high. Power will turn off to protect it. This message may indicate problem with the watch’s built-in pressure sensor, accelerometer, or gyrosensor.
Important! Note the precautions in this section whenever using this watch. Precautions During Use Display Information Accuracy Tide Graph Precautions For Japan area oceans, tide times and level changes are predictively calculated using harmonic constant data obtained from Bibliography 742 Tidal Harmonic Constants Tables, Japanese Coast (February 1992) published by the Hydrographic Department of the Japan Coast Guard, and from the List of Tidal Stations (2015) published by the Japan Meteorological Agency.
Moon Age Precautions Moon ages displayed by this watch are based on the calculation described below. (1) Elongation is calculated using solar and lunar coordinates produced by functional calculus. (2) Moon age is calculated based on the correlation between the elongation and average moon age. Though the lunar period averages 29.53 days, it actually fluctuates by as much as ±1 day, so this calculation produces an error of up to ±1 day.
The inside surface of the watch glass may fog when the watch is exposed to a sudden drop in temperature. No problem is indicated if the fogging clears up relatively quickly. Sudden and extreme temperature changes (such as coming into an air conditioned room in the summer and standing close to an air conditioner outlet, or leaving a heated room in the winter and allowing your watch to come into contact with snow) can cause it to take longer for glass fogging to clear up.
Using GPS Outside Your Country Some countries or geographic areas put legal restrictions on the use of GPS, on the collection and logging of location information, etc.
● Location measurements are performed using satellites that are operated and managed by the United States (GPS), Russia (GLONASS), and Japan (QZSS). Because of this, there is always the possibility that access to its information may be disabled at the discretion of these countries. Wi-Fi connectivity Note that when using a Wi-Fi connection you need to be aware of the watch’s battery level and your surrounding environment.
Thermal Shock Freezing Tested in accordance with Method 503.6 Procedure I-C. Tested in accordance with Method 521.4 Procedure I. Protective stickers ● Be sure to remove all protective stickers and/or paper tags that may be affixed to your watch (including its back cover) and/or its band when you purchase it.
Band Tightening the band too tightly can cause you to sweat and make it difficult for air to pass under the band, which can lead to skin irritation. Do not fasten the band too tightly. There should be enough room between the band and your wrist so you can insert your finger. ● Deterioration, rust, and other conditions can cause the band to break or come off of your watch, which in turn can cause band pins to fly out of position or to fall out.
Chemicals ● Do not allow your watch to come into contact with thinner, gasoline, solvents, oils, or fats, or with any cleaners, adhesives, paints, medicines, or cosmetics that contain such ingredients. Doing so can cause discoloration of or damage to the resin case, resin band and other parts. Storage ● ● If you do not plan to use your watch for a long time, thoroughly wipe it free of all dirt, sweat, and moisture, and store it in a cool, dry place.
Metal Components Failure to clean dirt from metal components can lead to formation of rust, even if components are stainless steel or plated. If metal components exposed to sweat or water, wipe thoroughly with a soft, absorbent cloth and then place the watch in a well-ventilated location to dry. ● Use a soft toothbrush or similar tool to scrub the metal with a weak solution of water and a mild neutral detergent, or with soapy water.
User Maintenance Caring for Your Watch Remember that you wear your watch next to your skin, just like a piece of clothing. To ensure your watch performs at the level for which it is designed, keep it clean by frequently wiping with a soft cloth to keep your watch and band free of dirt, sweat, water and other foreign matter. ● Whenever your watch is exposed to sea water or mud, rinse it off with clean fresh water. ● For a resin band, wash with water and then wipe dry with a soft cloth.
Premature Wear ● Leaving sweat or water on a resin band or bezel, or storing your watch in an area subject to high moisture can lead to premature wear, cuts, and breaks. Skin Irritation ● Individuals with sensitive skin or in poor physical condition may experience skin irritation when wearing a watch. Such individuals should keep their leather band or resin band particularly clean.
Main Specifications Common Specifications 1.32-inch dual layer display, Color TFT LCD (320 × 300 pixels) + Monochrome LCD Capacitive touch panel ● Microphone ● Vibration ● ● ● Battery: Type: Lithium-ion battery Charging time: Approximately 2 hours at room temperature (Be sure to use the special charger cable and AC adaptor.) Bluetooth: Bluetooth® 4.1 (Low Energy support) Wi-Fi: IEEE802.
● Watch: Auto time correction: By communication with smartphone (Time can be adjusted manually.) By GPS information (Can be corrected manually.) Time zones (world time function): Supports multiple world time zones (Types depend on system time zones.) 12/24-hour timekeeping Full auto-calendar: Auto switching by linking with smartphone Summer time: Auto switching by linking with smartphone Watch faces: Three favorites, more can be added.
Tide and Fishing: Tide graph: Past 12 hours + Next 12 hours Fishing time (Calculated according to current location, and moon hour angle and age.
● About MIL-STD-810G (United States military standard issued by the U.S. Department of Defense): Description: 1. Drop 2. Random Vibration 3. Humidity 4. Solar-Radiation 5. Non-Operating Altitude 6. Operating Altitude 7. Non-Operating High Temperature 8. Non-Operating Low Temperature 9. Temperature Shock 10. Icing Freezing Rain Procedure: MIL-STD-810G, w/change1 1: Method 516.7 ProcedureⅣ 2: Method 514.7 ProcedureⅠ 3: Method 507.6 ProcedureⅡ 4: Method 505.6 ProcedureⅡ 5: Method 500.
Model Specific Specifications Sensors Operating time on full charge*1 Operating temperature Colors Crystal Activity App MOMENT SETTER App Location Memory App Approx. Size (Body H × W × D) Approx.
*1 CASIO test conditions *2 GPS altitude information is used, so the indicated altitude may not exactly match the actual above sea level elevation or altitude. *3 In order to be able to use these functions your Android phone must have the CASIO MOMENT SETTER+ app installed, and there must be a connection between the phone and watch. These functions are not supported in the case of iOS. *4 Default: OFF *5 For models for which operation has been confirmed, refer to the Google check page. http://www.android.
Supplementary Information Open Source Information CASIO uses GPL, LGPL and other source code that comes under an open source license in this product. CASIO discloses the source code in accordance with each open source license. For source codes and details about each open source license, visit the CASIO website. Source code is provided “as-is” without any guarantees. However, this does not affect warranty conditions by CASIO concerning product defects (including defects in the source code).
This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects.
CASIO COMPUTER CO., LTD.