ES USER’S GUIDE GUÍA DEL USUARIO Please keep all information for future reference. Guarde toda información para tener como referencia futura. Safety Precautions Before trying to use the piano, be sure to read the separate “Safety Precautions”. Precauciones de seguridad Antes de intentar usar el piano, asegúrese de leer las “Precauciones de seguridad” separadas.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Company and product names used in this manual may be registered trademarks of others. This mark applies in EU countries only. CASIO Europe GmbH Bornbarch 10, 22848 Norderstedt, Germany This mark applies to the PX-800V only. Please keep all information for future reference.
PX800_e.book 1 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Contents Assembling the Stand .............................................................................................. E-35 Unpacking................................................................. E-35 To connect cords....................................................... E-39 Assembling the Stand............................................... E-35 To install the music stand.......................................... E-40 General Guide .............
PX800_e.book 2 ページ ２００６年１０月１２日 木曜日 午後１２時５分 General Guide Bottom 1-1 2 3 4 5 6 7 1-2* * The power cord of the PX-800 is hard-wired to the digital piano.
PX800_e.book 3 ページ ２００６年１０月１２日 木曜日 午後１２時５分 General Guide CAUTION • Make sure that the cover is fully open whenever you are playing on the keyboard. A partially open cover can suddenly close unexpectedly and pinch your fingers. NOTE • The names shown here are always indicated in bold when they appear within the text of this manual.
PX800_e.book 4 ページ ２００６年１０月１２日 木曜日 午後１２時５分 General Guide TEMPO/SETTING Button The TEMPO/SETTING button is used when configuring a variety of different digital piano settings. The following are TEMPO/SETTING button basics. z The lamp above the TEMPO/SETTING button flashes while the button is depressed, and goes out when the button is released.
PX800_e.book 5 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Power Supply Your digital piano runs on standard household power. Be sure to turn off power whenever you are not using the digital piano. 1. Make sure that the POWER button is in the OFF position (raised). POWER button ON (Power lamp on) OFF (Power lamp off) Front Power lamp 2. Connect the power cord that comes with the digital piano to the AC power jack on the bottom of the digital piano.* * PX-800V only 3.
PX800_02_e.fm 6 ページ ２００６年１０月１２日 木曜日 午後４時１３分 Connections IMPORTANT! • Whenever connecting something to the digital piano, first use the VOLUME controller to set the volume to a low level. After connecting, you can adjust the volume to the level you want. Connecting Headphones IMPORTANT! • The digital piano automatically adjusts sound output to optimize for headphone output (when headphones are connected) or built-in speaker output (when headphones are not connected).
PX800_e.book 7 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones / TONE POWER VOLUME TEMPO/SETTING METRONOME GRAND PIANO Selecting and Playing a Tone (Please wait!) Your digital piano has the following types of tones built in. Tone Numbers Tone Type Number of Tones 01 to 12 Keyboard* 12 001 to 020 Various 20 021 to 148 GM (General MIDI) 128 149, 150 Drum Sets 2 sets * You can select these tones using keyboard keys.
PX800_e.book 8 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones NOTE • The DSP* effect will be applied if you select a tone with DSP. • Note that the digital piano’s DSP resources are limited. Because of this, selecting a tone with DSP can cause notes that are currently being played to cut off (if they are being played using a tone with DSP), or it can remove the DSP effect from an operation (layer, split, demo tune) that was previously assigned a tone with DSP.
PX800_e.book 9 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones To assign a tone to the VARIOUS/GM TONES keyboard key 1. 1. While holding down the TEMPO/SETTING button, press the VARIOUS/GM TONES keyboard key. Keep the TEMPO/SETTING button depressed until you finish step 2 of this procedure. • This will cause the TEMPO/SETTING button to flash and the tone number of the Various, GM, or Drum Sets Tone currently assigned to the keyboard key to appear on the display. 2.
PX800_e.book 10 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones Layering Two Tones 5. Use the following procedure to layer two tones, so they sound at the same time. 1. 2. Hold down the TEMPO/SETTING button until you finish step 2 of this procedure. While holding down the keyboard key that corresponds to the main tone, press any nearby keyboard key that corresponds to another tone. • The second key you press is the layered tone. We will be changing it in step 3, below.
PX800_e.book 11 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones 3. Use the + and – buttons to turn keyboard split on or off. When the display shows this: It means this: oFF Keyboard split off on Keyboard split on • Releasing the TEMPO/SETTING button will cause the display to change to the number of the currently selected low-range tone. To configure reverb and chorus effect settings 1. While holding down the TEMPO/SETTING button, press the REVERB or CHORUS keyboard key.
PX800_e.book 12 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones 2. Use the + and – buttons to change the displayed value. To turn acoustic resonance and DSP on or off • Reverb Value To do this: Select this setting: Turn off reverb oFF Turn on reverb 1: Room 2: Small Hall 3: Large Hall 4: Stadium 1. • This will cause the lamp above the TEMPO/ SETTING button to flash and the currently selected acoustic resonance or DSP setting to appear on the display.
PX800_02_e.fm 13 ページ ２００６年１０月１２日 木曜日 午後６時５３分 Playing with Different Tones 2. Use the + and – buttons to change the displayed setting. When the display shows this: It means this: oFF Effect off on Effect on Using the Metronome 1. • This starts the metronome. • The two lamps above the SONG PLAY/STOP button flash in time with the metronome beat. 2. NOTE • While the keyboard is layered, the DSP on/off setting affects the layered tone only.
PX800_e.book 14 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing with Different Tones To adjust the metronome volume NOTE • You can perform the following procedure at any time, regardless of whether or not the metronome is sounding. 1. While holding down the TEMPO/SETTING button, press the METRONOME VOLUME keyboard key. Keep the TEMPO/SETTING button depressed until you finish step 2 of this procedure.
PX800_e.book 15 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing Back Built-in Songs SONG / TONE TONE/SONG SONG PLAY/STOP PART/TRACK IMPORTANT! • After you select a built-in song, it can take a number of seconds for the song data to be loaded. While the data is being loaded, the song number will flash on the display, and the keyboard keys and button operations will be disabled. If you are playing something on the keyboard, the following operation will cause output to stop. 1.
PX800_e.book 16 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Playing Back Built-in Songs Playing Back a Specific Music Library Song The Music Library includes both preset songs (01 to 60), plus up to 10 songs (61 to 70) that have been saved to digital piano memory from a computer* or loaded SD memory card (page E-29). You can use the procedure below to select one of these songs and play it back. * You can download music data from the Internet and then transfer it from your computer to digital piano memory.
PX800_e.book 17 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Recording and Play Back / SONG PLAY/STOP PART/TRACK RECORDER METRONOME You can store the notes you play in digital piano memory for later playback. You can have up to five songs in memory at one time. Songs and Tracks A track is a container of recorded data, and each song consists of two tracks: Track 1 and Track 2. You can record each track separately and then combine them so they play back together as a single song. Track 1 Record While playing back. .
PX800_e.book 18 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Recording and Play Back To record to a specific track of a specific song 5. • Tone (page E-7) * After selecting the tone you want, press the TONE/ SONG button one more time so the SONG lamp is lit. • Effect (page E-11) • Tempo (page E-24) After recording to either of the tracks of a song, you can record to the other track while listening to playback what you recorded in the first track. 1. Press the RECORDER button so the PLAY lamp is lit.
PX800_e.book 19 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Recording and Play Back To record to one track of a song while listening to the playback of the other track 1. 2. Press the RECORDER button so the PLAY lamp is lit. 2. Use the + and – buttons to display a song number (1 to 5). Use the + and – buttons to display a song number (1 to 5). Press the RECORDER button so the REC lamp is flashed. • This will cause the L/1 lamp to flash. 4. 1. Press the RECORDER button so the PLAY lamp is lit.
PX800_e.book 20 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Recording and Play Back Deleting Recorded Data The following procedure deletes a specific track of a song. IMPORTANT! • The procedure below deletes all of the data of the selected track. Note that the delete operation cannot be undone. Check to make sure you really do not need the data in digital piano memory before you perform the following steps. 1. Press the RECORDER button so the PLAY lamp is lit. 2.
PX800_e.book 21 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Configuring Settings with the Keyboard / TEMPO/SETTING You can use the TEMPO/SETTING button in combination with the keyboard keys to configure a wide range of digital piano settings, including the key, keyboard touch, MIDI settings, etc. • The same basic procedure (explained under “To configure settings with the keyboard” on page E-22) can be used for all settings. The only difference is the keyboard key that you press.
PX800_e.book 22 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Configuring Settings with the Keyboard To configure settings with the keyboard 1. Use the “Keyboard Setting Reference” on page E-23 to find the setting you want to configure, and note its keyboard key. Example: To change the key, you would need to use the keyboard key labeled TRANSPOSE 2. While holding down the TEMPO/SETTING button, press the keyboard key for the setting you want to configure. In this example, we will press the TRANSPOSE key.
PX800_e.book 23 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Configuring Settings with the Keyboard Keyboard Setting Reference ■ Keyboard To change this setting: Use this keyboard key: Settings Description Keyboard touch response TOUCH RESPONSE oFF : Off 1 : Strong sound is produced even when relatively light pressure is applied. 2 : Normal 3 : Normal sound is produced even when relatively strong pressure is applied. Specifies the relative touch of the keyboard keys.
PX800_e.book 24 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Configuring Settings with the Keyboard ■ Tones To change this setting: Use this keyboard key: Settings Description Tone selection TONE See “Tone List” on page A-1. See page E-8. Layered tone volume balance LAYER BALANCE –24 to 0 to 24 Specifies the volume balance between layered tones. A lower value reduces the volume level of the layered tone. Split on/off SPLIT ON/OFF on: On, oFF: Off See page E-10.
PX800_e.book 25 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Configuring Settings with the Keyboard ■ MIDI To change this setting: Use this keyboard key: Settings Description Send Channel MIDI/OTHERS C.01 to C.16 Specifies one of the MIDI channels (1 through 16) as the Send Channel, which is used for sending MIDI messages to an external device. When configuring this setting, use the procedure under “To configure a setting using the MIDI/OTHERS key” on page E-22. Local Control MIDI/OTHERS L.on: On L.
PX800_03_e.fm 26 ページ ２００６年１０月１２日 木曜日 午後４時１４分 Connecting to a Computer Connecting to the MIDI Terminal Connecting to the USB Port What is MIDI? MIDI is a standard for digital signals and connectors that allows musical instruments, computers, and other devices, regardless of manufacturer, to exchange data with each other. NOTE • For details about MIDI implementation, visit: http://world.casio.com/ The digital piano’s USB port makes it quick and simple to connect to a computer.
PX800_e.book 27 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Connecting to a Computer IMPORTANT! • Make sure that the digital piano is turned off before connecting or disconnecting the USB cable to it. Computer USB port USB cable (A-B type) USB connector Digital piano USB port Driver Minimum Computer System Requirements The following are the minimum computer system requirements for running the USB MIDI driver.
PX800_e.book 28 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Connecting to a Computer Expanding the Selections in the Music Library You can store up to 10 songs you have downloaded with your computer as songs 61 through 70 of the Music Library and practice along with them as they play, just as you do with the built-in songs. You can also use the CASIO SMF conversion software (SMF Converter) to convert SMF data you have purchased or created and save it as a Music Library song.
PX800_03_e.fm 29 ページ ２００７年６月４日 月曜日 午前１１時５８分 Using an SD Memory Card SONG /NO, /YES / SONG PLAY/STOP TONE/SONG TEMPO/SETTING CARD SD Memory Card Slot RECORDER Your digital piano’s SD memory card slot makes it possible for you to store song data on a commercially available SD memory card. The digital piano also can read SMF song data and CASIO format song data from an SD memory card. z Supported SD Memory Cards The maximum supported SD memory card size is 1 GB.
PX800_03_e.fm 30 ページ ２００７年６月４日 月曜日 午前１１時５８分 Using an SD Memory Card • An SD memory card can become quite warm after very long use in the SD memory card slot. This is normal and does not indicate malfunction. • An SD memory card has a limited service life. After very long use, you may start to experience problems with storing data to, or reading or deleting data from the memory card. When this happens, you need to purchase a new SD memory card. * Note that CASIO COMPUTER CO., LTD.
PX800_e.book 31 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Using an SD Memory Card 4. To stop playback, press the SONG PLAY/ STOP button. 5. After you are finished using the SD memory card, keep pressing the CARD button until its lamp turns off. To transfer song data from an SD memory card to the digital piano user area 1. Press the TONE/SONG button so the SONG lamp is lit. 2.
PX800_03_e.fm 32 ページ ２００６年１０月１３日 金曜日 午後１２時４９分 Using an SD Memory Card To transfer song data from an SD memory card to the recorder area 1. 2. Press the RECORDER button so the PLAY lamp is lit. Use the + and – buttons to display the number of the recorder area song (1 through 5) to which you want to transfer the data. This mark indicates that the currently displayed song number has data stored already. 3.
PX800_e.book 33 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Using an SD Memory Card 5. Use the + and – buttons to select the file number where you want to save the song data. 2. • “PLS” (PLeaSe wait) remains on the display while the formatting operation is performed. Never try to perform any other operation on the digital piano while the memory card is being formatted. The message “CPL” will appear on the display to let you know when the format operation is complete.
PX800_e.book 34 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Using an SD Memory Card SD Memory Card Errors Display Message Cause Action No SD memory card loaded in the SD memory card slot or the card is not loaded correctly. Correctly insert the SD memory card into the SD memory card slot. (Page E-30) You are trying to load data from an SD memory card that does not contain any data that is supported by this digital piano. 1. Use an SD memory card that contains files that can be loaded into digital piano memory.
PX800_e.book 35 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Assembling the Stand Unpacking Assembling the Stand PREPARATION • Before starting assembly, check to make sure that you have all the parts shown below. You can find the screws in a plastic bag inside of the polystyrene foam packing material. • This stand does not include any of the tools required for assembly. It is up to you to prepare a large Philips head (+) screwdriver for assembly.
PX800_e.book 36 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Assembling the Stand PREPARATION • Before starting assembly of the stand, divide the polystyrene foam packing material K into the sections shown in Figure 1. Use the packing material to secure side panels A and B as shown in Figure 2. You will have an easier time assembling the stand if the side panels are raised as shown in the illustration. • If you do not have any packing material available for some reason, use a magazine or some other thick item. 2.
PX800_e.book 37 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Assembling the Stand 3. With the speaker box C laying on its side as shown in the illustration, secure side panels A and B to the speaker box C. Secure the side panels using four screws D. • Insert screw caps at the locations indicated in the illustration and press them in as far as they will go. • Align the screw holes of the speaker box C with the screw holes of the side panels as you install the screws D.
PX800_e.book 38 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Assembling the Stand 7. Turn around the corner brackets as shown in the illustration, and insert them between pedal unit brackets I-(a) and I-(b), and the edges of the side panels. 8. Secure the corner brackets to the stand using the screws you removed in step 6. IMPORTANT! • When tightening the corner bracket screws, press down on the pedal unit to ensure that the pedal part comes into contact with the floor.
PX800_e.book 39 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Assembling the Stand To tighten the joint connector and screw (1) Rotate the screw counterclockwise about three turns to ensure that the screw is in the center of the joint connector. (2) Slowly rotate the screw clockwise and confirm that it tightens without resistance. If you feel any resistance, it means that the screw is not engaging properly with the joint connector. Rotate the screw counterclockwise again and try to get it to engage properly.
PX800_e.book 40 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Assembling the Stand 4. Plug the power cord that comes with the digital piano into the AC power jack on the bottom of the digital piano.* * PX-800V only 5. Plug the power cord into a household power outlet. IMPORTANT! • The shape of the power cord plug and household power outlet receptacle differ according to country and geographical area. The illustration shows just one example of the shapes that are available.
PX800_03_e.fm 41 ページ ２００６年１０月１２日 木曜日 午後４時４７分 Reference Troubleshooting Problem Cause Action See Page No sound is 1. The VOLUME controller is set to produced when I “MIN”. press a keyboard key. 2. Headphones are connected to the digital piano. 3. MIDI Local Control is turned off. 1. Rotate the VOLUME controller more towards “MAX”. 2. Unplug the headphones from the digital piano. 3. Turn on the Local Control setting. ) E-7 The pitch of the digital piano is off. 1.
PX800_03_e.fm 42 ページ ２００６年１０月１２日 木曜日 午後４時４７分 Reference Problem Playback stops part way through while transferring song data from my computer. Cause Digital noise from the USB cable or power cord caused data communication your computer and digital piano to be interrupted. “E-A” appears on the Built-in flash memory is corrupted. display immediately after power is turned on. Action See Page Stop song playback, disconnect the USB ) E-26 cable from the digital piano, and then reconnect it.
PX800_e.book 43 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Reference Product Specifications All of the items in these specifications apply to the PX-800 and PX-800V, unless specifically noted otherwise.
PX800_e.book 44 ページ ２００６年１０月１２日 木曜日 午後１２時５分 Reference Operating Precautions Be sure to read and observe the following operating precautions. ■ Location Avoid the following locations for this product. • Areas exposed to direct sunlight and high humidity • Areas subjected to temperature extremes • Near a radio, TV, video deck, or tuner The above devices will not cause malfunction of the product, but interference from the product can cause audio or video interference of a nearby device.
PX800_s.book 1 ページ ２００６年１０月１７日 火曜日 午後４時３３分 Appendix/Apéndice Tone List/Lista de tonos No./ Nº 01 Tone Name/ Nombre de tonos Program Change/ Cambio de programa Bank Select Maximum MSB/ Polyphony MSB de /Polifonía selección máxima de banco No.
PX800_s.book 2 ページ ２００６年１０月１７日 火曜日 午後４時３３分 Appendix/Apéndice No.
PX800_s.book 3 ページ ２００６年１０月１７日 火曜日 午後４時３３分 Appendix/Apéndice Song List/Lista de canciones No./Nº Song Name/Nombre de canciones 01 Nocturne Op.9-2 02 Fantaisie-Impromptu Op.66 03 Étude Op.10-3 “Chanson de l’adieu” 04 Étude Op.10-5 “Black Keys” 05 Étude Op.10-12 “Revolutionary” 06 Étude Op.25-9 “Butterflies” 07 Prélude Op.28-7 08 Valse Op.64-1 “Petit Chien” 09 Valse Op.64-2 10 Moments Musicaux 3 11 Impromptu Op.
MIDI Implementation Chart Model PX-800 Function... Transmitted Recognized Basic Channel Default Changed 1 - 16 1 - 16 1 - 16 1 - 16 Mode Default Messages Altered Mode 3 X Mode 3 X 21 - 108 0 - 127 0 - 127*1 O 9nH v = 1 - 127 X 8nH v = 64 O 9nH v = 1 - 127 X 9nH v = 0.
This recycle mark indicates that the packaging conforms to the environmental protection legislation in Germany. Esta marca de reciclaje indica que el empaquetado se ajusta a la legislación de protección ambiental en Alemania.
