Basic Manual Contents/Ready Phone Call Inputting Characters Address Book/ Pair Function Mail/ Hello Messenger Camera EZweb EZ Navi EZ FeliCa EZ・FM PC Site Viewer Smart Mode/ Teens Mode Other Functions Troubleshooting/ Remote Auto Lock Index
Introduction Thank you for purchasing the W43CA. Before using it for the first time, be sure to read the W43CA Basic Manual (this PDF manual) so as to know how to use it correctly. After you finish reading this manual, store it and the printed materials that come with the phone in a safe place for future reference. Printed Manuals for the W43CA (Japanese) The W43CA comes with a Basic Manual and an Instruction Manual.
Cellphone Etiquette Mind your manners! A cellphone always emits weak radio waves while it is turned on. Enjoy operation of your cellphone without forgetting to be considerate of those around you. Some locations do not allow the use of cellphones. ■ Using a cellphone while driving is dangerous and prohibited by Traffic Control Law. ■ Using a cellphone inside of an aircraft is prohibited by law. Be sure to turn off your cellphone before takeoff.
Cellphone Basics Features Camera Shoot photos and record movies, and send them by e-mail. Page 59 PC Site Viewer View WEB sites created for viewing on PCs. Page 85 EZ Navi EZ Navi Walk, Position Search, and Area Message allow you to get various kinds of location information. They are all built-in functions. Page EZ FeliCa Hello Messenger Security Setup Use the cellphone for shopping by using e-money, or use it as member’s cards, point cards, and so on.
Manner Mode and Easy Voice Memo Manner Mode Easy Voice Memo Use Manner Mode to turn off the ring tone so as not to bother others around you. While the standby screen is displayed, hold down ( for about one second. Shhhhhhh! Page If you cannot answer a call, Easy Voice Memo plays an answering message and records the caller’s message. While the standby screen is displayed, hold down C for about one second.
Never use your cellphone while driving! Holding a cellphone in your hand, talking on a cellphone, or looking at a cellphone display to send mail or to perform any other operation while driving is prohibited by Japanese law. (Revised Traffic Control Law, effective November 1, 2004) × Reading mail or looking at the display. × Holding a cellphone in your hand to talk. Turn off your cellphone or use Drive Mode while driving.
Beware of spam and one-ring calls! How to Combat Spam You can set up mail filters to block specific mail or mail identified as “未承諾広告※” (unsolicited advertisement), which often includes spam. Your cellphone has the following filters to block spam.
Disaster Message Board Service Disaster Message Board The Disaster Message Board lets you use EZweb to register information about your well-being in case of a major disaster. The information you register can be accessed from anywhere in Japan over EZweb or the Internet.
Registration Access Disaster Message Board top screen Information screen Information registration screen ※ Registration contents are retained for up to 72 hours. ※ You can register up to 10 entries per phone number. Registering a new entry while there are already 10 registered entries, automatically overwrites the oldest entry.
Contents Cellphone Etiquette Mind your manners! ........................................................................... 1 Cellphone Basics Features ............................................................................................ Manner Mode and Easy Voice Memo ................................................ Checking Power, Signal Strength, and Battery Level ........................ Never use your cellphone while driving! ............................................
Hello Messenger ............................................................................................................................. 55 Contents Displays the Hello Messenger Menu ............................................... 56 Invite the Members to the Meeting .................................................. 57 When You Get an Invitation Message to Join .................................. 58 Camera Features .....................................................................................
Ready All Before using the W43CA, check the contents of the package comes with your W43CA. You should also familiarize yourself with basic operations, like how to charge the battery, how to turn the power on, etc.
Names of Parts ■ Back Infrared port Earpiece Camera lens Photo light/ Standby light/Incoming/ Charge indicator(LED)/ Camera start indicator W43CA Main display Ready ■ Front Sub display Center key Cursor key Stereo speaker Optical sensor Application key Charging terminals Address book key EZ/AF lock key Mail key Answer/ Pair key Memo/Clear key End/Power key Battery pack/cover Number keys FeliCa mark Microphone Lock cancellation button Built-in antenna ※ Strap eyelet ※ Take care to avoi
Charging the Battery Pack The battery pack that comes with the phone is not fully charged when you purchase it. Be sure to charge the battery pack before using the W43CA for the first time. Charging takes about 150 minutes. You should recharge the battery pack whenever the battery level icon or . shows Check the shape of the connectors to ensure they are aligned correctly when you connect them. • Charging : LED indicator is lit red. • Charging complete : LED indicator goes out.
Check the shape of the connectors to ensure they are aligned correctly before you connect. Trying to force a connection may damage the connectors. Ready Connect the common AC adaptor 01 (option) to the desktop holder. Fold out the power plug of the common AC adaptor 01 (option), and then plug it into a 100V AC power outlet. Insert the W43CA into the desktop holder.
Turning On Power Hold down F for at least 2.5 seconds. The standby screen appears. icon Signal Strength Strong Medium Weak Very Weak Out of Range • Communication is not possible while the signal strength icon is (Out of Range). • Communication may not be possible while the signal strength icon is (Very Weak).
The W43CA lets you use the numbers and passwords described below. Be sure to take steps so you do not to forget your numbers and passwords. You will need them to perform various operations and to access subscription services.
Selecting English as the Display Language While the standby screen is displayed, press c. Use a to select “ 機能設定 ” (Settings), and then press c (OK). Press 3 ( 画面表示/照明 ) (ScreenSetup/DisplayLighting).
5 (Set Language). Ready 2 (English). This selects English as the display language. Even if English is selected as the display language, schedule and other dates are displayed in the format year/month/day. Folder names inside of the Data Folder are also displayed in year/month/day format.
Operation Basics u • Selects news flash telop, ■ Key functions • l • Displays incoming records. r • Displays outgoing records. Returns to the previous menu screen. • Selects an item. • Scrolls forward one menu screen. • Selects an item. • d • Displays the standby • % L • • • news flash window. Selects an item. shortcut icon. Selects an item. c • Displays the main menu. Displays the EZ apps menu. & • Applies an item. • Displays the address book.
Display Indicators 12 34 5 678 9 ! 1 Signal strength 2 Battery level 3 The microSDTM memory card (commercial item) is inserted into the cellphone. 4 During a call ) 5 / 6 7 ~ " # $% & Main display 1 2 EZ apps (BREW®)/Hello Messenger on Unread mail / / au Music Player/SD-Audio Player/EZ•FM on 8 Key guidance on the EZweb screen (while browsing) or the EZ Channel-plus program screen (while playback), etc. 9 Current time The date and time are set automatically.
Main Menu Pressing c while the standby screen is displayed displays the main menu. Use a to select the icon, and then press c (OK) to access the function associated with the icon. Camera Music microSD Menu Hello Messenger Data folder EZ FeliCa Menu Function/Setup W-Scene Settings Watch/Calendar Accessories PC site viewer Menu EZ·FM ■ Using the Main Menu Example: To display the setting screen from the main menu. Press a to select “Settings,” and c then press c (OK).
■ Using Soft Keys Left Center Right Left soft key % Center soft key c Right soft key & Ready Soft keys are the keys you use to execute the functions along with the bottom of the screen. The table below explains how to assign the soft keys to the onscreen functions. Note that the function of each soft key depends on the currently displayed screen. Executes the function on the left. Executes the function on the center. Executes the function on the right.
Initializing E-mail and EZweb An EZweb subscription is required to use e-mail and EZweb. If you did not subscribe when you purchased your phone, contact your nearest au shop or the au Customer Service Center. ※You will be assigned an e-mail address automatically when you perform the EZweb initialization procedure. While the standby screen is displayed, press L. Press c (OK). Wait until the phone connects to the server for initialization.
My phone number and mail address Ready Looking Up Your Current Phone Number and E-mail Address While the standby screen is displayed, press c. Use a to select “Settings,” and then press c (OK). Press 0 (Profile). Your current phone number and e-mail address appear. You can also look up your phone number and e-mail address by pressing c, and then 0 while the standby screen is displayed.
Changing Your E-mail Address E-mail address △△△@ezweb.ne.jp Part you can change Domain name While the standby screen is displayed, press L. Press 0 (E-Mail Setup). Press 7 (Other Setup). When the EZweb connection confirmation screen appears, press 1 (Yes). Press 1 (E メールアドレ スの変更 ) (Change E-mail Address).
Ready Enter your Security Code, press c (OK), use j to select “ 送信 ” (Send), and then press c (Select). Use j to select “ 承諾する ” (Accept), and then press c (Select). Use j to select the text box, and then press c (Edit). Enter the e-mail address you want, and then press c (OK). To input an e-mail address → “Inputting an E-mail Address” (page 35) Use j to select “ 送信 ” (Send), and then press c (Select). The e-mail address confirmation screen appears. Press j to select “OK,” and then press c (Select).
Phone Call Making a Call While the standby screen is displayed, use the number keys (0 to 9) of the keypad to enter the phone number you want to call. When calling a standard phone, you need to enter the area code. Press N. After you finish a call, press F to hang up. Send Methods Displayed when you press c (Call) in step 2. Call : Your phone number is provided to the party you are calling in accordance with the caller ID setting of your phone.
Redialing (Outgoing Records/ Incoming Records) Phone Call While the standby screen is displayed, press s. r : Displays outgoing records. l : Displays incoming records. Use j to select the record whose number you want to dial, and then press N. The phone stores up to 50 records each for the outgoing records and incoming records. When a record is created while there are already 50 records in memory, the oldest current record is deleted automatically to make room for the new one.
Changing the Ring Tone While the standby screen is displayed, press c. Use a to select “Settings,” and then press c (OK). Press 2 (Sound/Vib/ LED). Press 1 (Incoming Call).
Press 2 (Melody). To hear the currently selected ring tone, press % (Check). Phone Call Press 1 (Fixed Sound). Use j to select the ring tone you want, and then press c (OK). The ring tone is set. ◎ The initial setting is “Incoming Tone1.” ◎ You can also download a “Chaku-Uta®” from the Internet and use it for your ring tone.
Adjusting the Ring Tone Volume To adjust the ring tone volume, perform steps 1 through 3 under “Changing the Ring Tone” (page 28), and then continue with the following steps. Press 1 (Incoming Call). Press 1 (Volume). To hear the ring tone at the current volume setting, press % (Play). Use j to adjust the ring tone volume, and then press c (OK). u : Increases volume. d : Decreases volume. Step-up : Ring tone volume gradually increases. Step-down: Ring tone volume gradually decreases.
Adjusting the Earpiece Volume during a Call Hello? Phone Call During a call, use j to adjust the volume. u: Increases volume. d : Decreases volume. You can adjust the earpiece volume (level 1-6). When you set the maximum volume (level 6), is displayed on the screen. Turning On Manner Mode While Manner Mode is set to on, the phone alerts you to incoming calls by vibrating. While the standby screen is displayed, hold down ( for about one second.
Turning On Easy Voice Memo While the standby screen is displayed, hold down C for about one second. This turns on Easy Voice Memo, the icon appears on the display while Easy Voice Memo is turned on. You can use Easy Voice Memos (up to 4 memos), and each memo can contain up to 20 seconds recording time. If a new Easy Voice Memo is recorded when there are already four memos in memory, the oldest, unprotected memo that has already been played back is deleted automatically to make room for the new one.
Playing an Easy Voice Memo Phone Call When there is a recorded Easy Voice Memos The message “ Call” and “ EasyVoiceMemo” appear on the standby screen. Select “ Call,” and then press c (OK). The incoming records list appears. Use j to select the record with the icon, and then press c (Disp). The incoming record detail screen appears. Use j to select “ EasyVoiceMemo,” and then press c (Play). The easy voice memo plays back. To delete an Easy Voice Memo, press C42 while the standby screen is displayed.
Inputting Characters Input characters using keypad keys 0 through 9. The table below shows the characters each key cycles through when you press it. d e f Number of Presses 1 2 3 4 5 6 7 8 1 . @ - _ / : ~ 1 2 a b c A B C 2 Key 3 d e f D E F 3 4 g h i G H I 4 5 j k l J K L 5 6 m n o M N O 6 7 p q r s P Q R 8 t u v T U V 8 9 w x y z W X Y 0 0 .
Inputting an E-mail Address mark@ ■ Inputting “mark@ezweb.ne.jp” In this example, we will input “mark@ezweb.ne.jp” for “<E-Mail Add1>.” To input “<E-Mail Add1>,” perform steps 1 through 6 under “Registering an Address Book” (page 38), and then perform the following steps. To input “m”: Press 6 once. To input “a”: Press 2 once. To input “r”: Press 7 three times. To input “k”: Press 5 twice. Inputting Characters Input “mark.” Press & (Menu).
Inputting Pictographs and Useful Sentences The following procedure shows how to input pictographs and useful sentences into the body text when creating a new e-mail message. Press % (Char), and then 6 (Pictograph). You can also select a pictograph by pressing #. Use a to select the pictograph you want, and then press c (Select). Use L and R to scroll through the various categories of pictographs. To input consecutive pictographs, press & (Serial).
Use j to select the useful sentence you want, and then press c (OK). Here we will select “Happy birthday!.” You can also input “Happy birthday!” by pressing 17. Inputting Characters The following shows the input screens for symbols (double-byte) and emoticons. Symbol (Double-byte) Input In step 1 of the above procedure, press % (Char), and then 5 (&@) to display the “FullSym” (double-byte symbol menu).
Address Book Registering an Address Book While the standby screen is displayed, hold down & for about one second. Select “ <Name>,” and then press c (Edit). Enter the name, and then press c (OK). The <Reading> is generated automatically when you enter a name. To input text → “Inputting Characters” (page 34) Use j to select “ <Phone Number1>,” and then press c (Edit).
Enter the phone number, and then press c (OK). When entering the number of a standard phone, be sure to include the area code. If you do not want to enter an e-mail address, jump to step 8. Enter the e-mail address, and then press c (OK). Address Book Use j to select “ <E-Mail Add1>,” and then press c (Edit). To input an e-mail address → “Inputting an E-mail Address” (page 35) Press & (Reg). ◎ The Address Book can contain up to 700 records. ◎ Address Book Records are numbered from 000 through 699.
Editing an Address Book Record Address... Birthday... Group... Example: To edit the phone number of “Tom Carter” While the standby screen is displayed, press &, use a to select the record you want to edit, and then press & (Menu). Press 3 (Modify), and then 1 (Overwrite). Use j to select “ 0900006XXXX,” and then press c (Edit). Make the changes you want, press c (OK), and then & (Reg). To delete characters, press C.
Adding Outgoing or Incoming Record Data to the Address Book r: Displays outgoing records. l: Displays incoming records. Address Book While the standby screen is displayed, press s, use j to select the phone number you want to save, and then press & (Menu). Press 4 (Reg Add Book). Press 1 (Reg New). To enter the name, use the procedure starting from step 2 under “Registering an Address Book” (page 38).
Dialing from the Address Book While the standby screen is displayed, press &, and then use a to select the record whose phone number you want to dial. Press c (Disp). The details screen of the record appears. Use j to select the phone number, and then press N.
Pair Function You can save up to five phone numbers (like frequently used ones from the address book). You can make calls, send mails to or use Hello Messenger with these saved numbers (called Pair Partners) more easily. Registering a Pair Partner If the Pair partner is not registered, the confirmation screen appears. Press c (OK). Use s to select the 1 through 5 tab where you want to register the Pair partner. Pair Function While the standby screen is displayed, press N.
Making a Phone Call, Sending Mail, Invite a Pair Partner to a Hello Messenger Meeting While the standby screen is displayed, press N. Use s to select the Pair partner. Use j to select “Call,” and then press c (OK). Selecting “Send E-Mail”/“Send C-Mail,” and then pressing c (OK) will display a screen for composing and sending an e-mail/a C-mail message. Next, continue from step 5 of the procedure under “Creating and Sending E-mail Messages” (page 47)/“Creating and Sending C-mail Messages” (page 53).
Mail EZweb subscription required Your W43CA supports two types of mail: e-mail and C-mail. Using E-mail Mail To use e-mail, you need to subscribe to an EZweb service. If you did not subscribe when you purchased your phone, contact your nearest au shop or the au Customer Service Center. In addition to an EZweb subscription, you also need to perform an initialization procedure before you can use e-mail. If you have not performed initialization yet, refer to “Initializing E-mail and EZweb” (page 22).
Using C-mail C-mail lets you exchange text messages that contain up to 50 double-byte characters (100 single-byte characters) with another au Page 53 cellphone that supports C-mails. W43CA C-mail Center Cente W43 CA Sent using a phone number. Example: 090-0001-XXXX Received using a phone number. Example: 090-0002-XXXX C-mail can be sent to another au cellphone.
Creating and Sending E-mail Messages While the standby screen is displayed, press L, and then press 1 (Create New). Mail Select , and then press c (Edit). : Address to which the e-mail will be sent. You can send an e-mail up to five addressees at a time. Press 1 (Address Book), use a to select an addressee, and then press c (Select). You can select an addressee from sending records, receiving records, or My Address, or you can enter an address.
Use j to select , and then press c (Edit). : Subject of the e-mail message. Enter the subject, and then press c (OK). Use j to select , and then press c (Edit). : Body of the e-mail message. Enter the body text, and then press c (OK). Press % (Send) or N. The message “Sent.” appears on the display after the e-mail message is sent.
Reading Received E-mail Messages When you receive an e-mail The message “ E-Mail” and appear on the standby screen. Received e-mail icon Mail Select “ E-Mail,” and then press c (OK). Press c (OK). : Indicates an unread message. : Indicates an already read message. Use j to select the unread e-mail you want to view, and then press c (Disp). The received e-mail message appears. If all of the message cannot be displayed, press d to scroll. Use L and R to scroll between messages.
Reading an E-mail Message with an Attached Photo or Movie Example: To see a photo attached to an e-mail. Use j to select the e-mail message, and then press c (Disp). Use j to select a file name, and then press c (Play). ◎ Depending on the size of the photo or movie file, the file may not appear within the mail in step 2 of the above procedure. If this happens, select the file name and press c (Rcv), c (Play). ◎ The sending and receiving operations may take longer when a mail message has data attached.
Replying to a Received E-mail Message ly Rep To reply to an e-mail message, perform steps 1 through 3 under “Reading Received E-mail Messages” (page 49), and then perform the following steps. Press % (Reply). Mail Press c (Edit), and then enter the body text. is prefixed with “Re:,” and the body text of the e-mail is quoted. For the remainder of this procedure → Perform the procedure starting from step 7 under “Creating and Sending E-mail Messages” (page 47).
Avoiding Spam It is recommended that you use our mail filter function to block spam. You can use “Supportive settings” to easily configure mail filter settings by answering questions that appear on the display. ■ Configuring Mail Filter Settings Example: To access the “サポート設定 ” (Supportive settings) 1 While the standby screen is displayed, press L. 2 Press 0(E-Mail Setup) 6(Mail Filter) 1(Yes). 3 Use j to select “ 次へ ” and then press c(Select). 4 Enter your Security Code, press c(OK).
Creating and Sending C-mail Messages Hold down ... While the standby screen is displayed, hold down L for about one second, and then press 1 (Create New). Mail Select , and then press c (Edit). Press 1 (Address Book), use a to select an addressee, and then press c (Select). You can also select a phone number from sending records or receiving records, or you can enter an address. Use j to select the phone number you want to enter, and then press c (OK).
Use j to select , and then press c (Edit). Enter the body text, and then press c (OK). Press % (Send) or N. When the C-mail reaches the other party, the message “Completed.” appears, and the message is stored in your sending records. Reading Received C-mail Messages When you receive a C-mail. The message “ C-Mail” and appear on the standby screen. Select “ C-Mail,” and then press c (OK). : Indicates an unread message. Use j to select the unread C-mail you want to view, and then press c (Disp).
Hello Messenger “Hello Messenger” is like a portable chat room which allows you to send text, sound and photo in real time to all the chatters (using au cellphone supporting this service). All chatters are represented by cartoon-style characters they selected. The host can invite up to 4 people from the address book entries. Hello Host Hello Hello Messenger Member 1 Send text messages. W43CA Member 2 Voice call Member 4 Member 3 Shoot and send the photos. Send text messages.
Displays the Hello Messenger Menu While the standby screen is displayed, press c. Use a to select “Hello Messenger,” and then press c (OK). When you start Hello Messenger for the first time, press c (OK) and select your own cartoon-style character, then press c ( 設定 )(Setting).
Invite the Members to the Meeting You can invite the members to start the meeting. To start the meeting, perform steps 1 through 2 under “Displays the Hello Messenger Menu” (page 56), and then continue with the following steps. Use j to select “ スター ト ” (Start), and then press c ( 選択 )(Select). Hello Messenger Use j to select “ アドレス帳 ” (Address Book), and then press c ( 選択 )(Select). Use a to select the members.
◎You can register the member from “ハローランキング” (Hello Ranking) or “グループ” (Group). ◎You can activate Hello Messenger from address book, outgoing/incoming records, phone number input screen to start the meeting. When You Get an Invitation Message to Join When you get an invitation message to join, ring tones sounds or your cellphone vibrates. The invitation screen (inviting you to join the meeting) appears.
Camera Features Your W43CA comes with a built-in 2.1-megapixel, 2.07-million effective pixel camera to shoot photos and record movies. You can attach the photos and movies that you shot/recorded to e-mail messages. Using the Camera Shooting a Photo (page 61) 1 Recording a Movie (page 62) Use your images for W43CA functions! 2 W43CA Camera You can use photos you shot for the standby screen, for the image that appears while the ring tone is sounding, and in your address book.
Tips for Better Photos Shooting a VGA, SXGA, or UXGA size image Do not cover the lens or optical sensor with your hands. Hold the camera securely with both hands. Use your thumb to press c (Shutter) to release the shutter. Do not cover the lens or optical sensor with your hands. Hold the camera securely with both hands. Use the index finger of your right hand to press b to release the shutter. W43CA Shooting a Phone, Wallpaper size, etc.
Camera Shooting a Photo While the standby screen is displayed, press c, use a to select “Camera,” and then press c (OK). Camera Press 1 (Photo). Point the lens at the subject, and then press c (Shutter). The phone emits a shutter sound. Note that the phone emits the shutter sound even if it is in Manner Mode. You can also press b in place of c. Check the subject through the monitor screen (within the ), and release the shutter. area indicated as Press c (Save).
Recording a Movie While the standby screen is displayed, press c. Use a to select “Camera,” and then press c (OK). Press 2 (Movie), point the lens at the subject, and then press c (Rec). The phone emits a shutter sound to signal the start of recording. Note that the phone emits the shutter sound to signal the start of recording even if it is in Manner Mode. You can also press b in place of c. To stop recording, press c (End).
■ Meanings of the Photo Titles The initial photo mode setting when you purchase your W43CA is “Phone Mode (Wallpaper 240×320)”. Meanings of the Photo Titles in the “Photo Folder,” which is in the Data Folder. Example of a Photo Title Date: October 24, 2006 061024_1123∼0001 Time: 11:23 a.m. Serial Number When You Shot Photos Mistakenly If the shot photo is not what you want, press C or l in step 4 of the above procedure. Next, repeat step 3 to reshoot.
Viewing Photos and Movies While the standby screen is displayed, press c, use a to select “Data folder,” and then press c (OK). Use j to select “Photo Folder,” or “Movie Folder,” and then press c (Detail). Selecting “All Data” displays a list of all photos and movies in the “Photo Folder” or “Movie Folder.” Use j to select the dated (by recording date) folder, and then press c (Detail). A list of all movies that were recorded on that day are displayed.
Attaching a Photo or Movie to an E-mail Message Perform the procedure from step 1 to 3 under “Shooting a Photo” (page 61) or “Recording a Movie” (page 62), and then perform the following steps. Press % (E-Mail), and then press 1 (Attach). Photos you shot are stored in the “Photo Folder” and movies are stored in the “Movie Folder,” (those folders are in the Data Folder). Camera Perform the procedure starting from step 2 under “Creating and Sending E-mail Messages” (page 47) to create an e-mail message.
EZweb EZweb subscription required Using EZweb To use EZweb, you need to subscribe to an EZweb beforehand. If you did not subscribe when you purchased your phone, contact your nearest au shop or the au Customer Service Center. In addition to an EZweb subscription, you also need to perform an initialization procedure before you can use EZweb. If you have not performed initialization yet, refer to “Initializing E-mail and EZweb” (page 22).
Displaying the EZ Top Menu While the standby screen is displayed, press R, use s to select “EZweb,” and then press 1 (Top Menu).
Bookmarking Sites You Frequently Access Bookmark it! Display favorite sites you want to bookmark, and press & (BrowserMenu). Press 1 (New bookmark). ※ You may not be able to bookmark some sites. Press & (Reg). Use j to select a folder, and then press c (OK). The message “Registered” appears when completed. You can have up to 100 sites bookmarked in the Favorite Sites.
’s go et e! he r L Viewing Sites saved to the Favorite Sites While the standby screen is displayed, press R. EZweb Use s to select “EZweb,” and then press 2 (Favorite Site). Use j to select a site or folder, and then press c (OK). If you selected a folder, use j to select a site, and then press c (OK).
Downloading Chaku-Uta® To download a Chaku-Uta®, perform step 1 under “Displaying the EZ Top Menu” (page 67), and then perform the following steps. Use j to select “ カテゴリで 探す ” (Search by Category), and then press c (OK). Use j to select “ 着うた ” (Chaku-Uta®), and then press c (Select). Select the content (desired information site), and download it. In order to use fee-based contents, you need to enter your EZ password or premium EZ password.
Downloading Chaku-Uta-Full® While the standby screen is displayed, press R, use s to select “au Music.” Press 2 “Jump to EZ Music!.” EZweb This operation connects the phone to “EZ Music!.” For the operations after connecting, follow the instructions displayed on the screen. You can also download Chaku-Uta-Full® by selecting “着うたフル” (ChakuUta-Full®) in step 2 under “Downloading Chaku-Uta®” (page 70).
Checking Charges You can check call and transmission charges. While the standby screen is displayed, press c11. When the EZweb connection confirmation screen appears, press 1 (Yes). Use j to select the item you want to check, and then press c (Select).
EZ Channel-Plus EZweb subscription required EZ Channel-Plus provides the latest programs you registered to download. Each updated content is automatically downloaded to your W43CA. ■ Displaying EZ Channel-Plus Menu Use s to select „ “ EZ Channel-plus. Press R. Standby screen EZweb memu EZ ChannelPlus memu ■ Enjoying EZ Channel-Plus ① Register the programs you are interested in. You can register up to 16 programs from “Jump to Program Guide.” ※ © KDDI ② Playback the program.
EZ Navi Features EZweb subscription required EZ Navi uses global positioning system (GPS) information to provide you with useful information. You can use various sites such as “EZ Navi Walk” that navigates you to your destination, “Position Search” that allows you to check where your child is, and “Area Message” that lets you know when your child is coming close to the destination. Use s to select “ EZnavi.” PressR.
“EZnaviwalk” A menu of useful options you can use while you are out. The latest news and featured information ※ “おためしナビ”(Navi Demo) provides the demonstration of voice navigation or Voice input function.
Security Navi Features EZweb subscription required Position Search Features When your child does not come home early and you are worried if your child may be lost, you can check the current location of your child by a map with a simple operation. There are two kinds of services of “Position Search”: “Auto Position Search” and “Position Search Mail”.
Area Message Features This service lets you configure two au phones with specific areas and specific times. Whenever a child carrying one of the phones approaches (or is inside of) the specified area during the specified a time period, an e-mail alert is sent to the other phone. Area Message can also be configured so an e-mail alert is sent when the child leaves (or is outside of) a specified area. “エリア通知” (Area Message) Features He’s arrived at cram school.
EZ FeliCa EZweb subscription required EZ FeliCa is a service available for the cellphones loading the technology of contact-free IC cards called FeliCa. Simply by holding W43CA over reader/writer (external device)※, you can use W43CA for shopping by using e-money or use it as member’s cards, point cards, and so on. When you use EZ FeliCa, you need to download the applications from the provider of the service you want to use. “QUICPayTM” (クイックペイ) is prepared at the time of purchasing.
Communicating with Reader/Writer You can use EZ FeliCa simply by holding the FeliCa mark over reader/writer. Hold the FeliCa mark of W43CA over reader/writer. FeliCa mark EZ FeliCa ◎ You can use EZ FeliCa without starting FeliCa-supported EZ apps. ◎ EZ FeliCa is available even when the power is turned off. However, while FeliCa Lock is active, or the battery level is very low, you may not be able to use EZ FeliCa. ◎ FeliCa antenna is built-in Battery pack cover.
Setting FeliCa Lock You can restrict the use of EZ FeliCa by setting FeliCa Lock on. You can temporarily release the FeliCa Lock and use EZ FeliCa for a certain period of time by holding down r for about one second while the standby screen is displayed and entering the lock No. (quick release). While the standby screen is displayed, press c4 141. Press 1 (ON), enter the lock No., and then press c (OK). The FeliCa Lock is set.
Using FeliCa-supported EZ apps “QUICPayTM” ( クイックペイ ) is prepared as FeliCa-supported EZ apps in W43CA at the time of purchase. ■ Starting FeliCa-supported EZ apps While the standby screen is displayed, press c. Use a to select “EZ FeliCa,” and then press c (OK). EZ FeliCa menu appears. EZ FeliCa menu The list of the FeliCa-supported EZ apps saved in W43CA is displayed. Select the EZ apps you want to start. EZ FeliCa Press 1 ( アプリ一覧 ) (EZ apps List).
EZ•FM EZweb subscription required The W43CA allows you to listen to the FM radio. Before using EZ•FM ■ Connecting Casio round-type earphone jack conversion adaptor 01 and MDR-E0931 by SONY Open W43CA flat type earphone terminal cover, connect a Casio round-type earphone jack conversion adaptor 01 and MDR-E0931 by SONY.
Listening to the EZ•FM While the standby screen is displayed, press c, use a to select “EZ•FM,” and then press c (OK). The precautions appear. Read the precautions, and then select “ 承諾する ” (Accept). If you select “ 承 諾(次回から非表示)” (Not display hereafter), they will not appear after the next time. Frequency area Radio station/ Song title area EZ • FM screen Press C. You can switch between Frequency area and Radio station/Song title area.
■ Adjusting the volume Press j on the EZ•FM screen to adjust the volume. u : Increases volume. d : Decreases volume. ※ There are 20 levels for the volume. ■ Tuning the radio frequency Press C on the EZ•FM screen, and then select the frequency area. s : Tuning (by 0.1MHz) s (hold down for about one second): Automatic tuning When you select the song title area, using s key allows you to select the radio station.
PC Site Viewer Features EZweb subscription required To use the PC site viewer, an EZ WIN course subscription is required. If you did not subscribe when you purchased your cellphone, contact your nearest au shop or the au Customer Service Center. Using the PC site viewer, you can comfortably view the WEB sites just like those you usually view with your PC, by high speed packet transmission of 2.4 Mbps down at maximum.
PC Site Viewer Mastering Operation Basics While the standby screen is displayed, press c. Use a to select “PC site viewer,” press c (OK), and then press & (OK). Warning message on packet transmission appears. Press 1 (トップページ) (Top Page). The initial setting is “Duogate” (http://duogate.jp/). ※ The contents displayed on the right is an example, and it may differ from the contents that actually appear on the display of your phone. Press s. The display scrolls. Use j to select the links on the screen.
Using Standby Assignment It’s updated. You can set a portion of a WEB site as the standby screen. You can set it to be automatically-updated at specified intervals. When a specified time elapses on the standby screen, the WEB site selected by “ 待受指定 ” (Standby Assignment) is displayed. To use “ 待受指定 ” (Standby Assignment), perform steps 1 through 4 under “Mastering Operation Basics” (page 86), and then perform the following steps. Display your favorite page, and then press & (メニュー) (Menu).
Press c (編集) (Edit), enter the title, and then press c (OK). Press & (登録) (Register), and then press & (設定) (Setting). Use j to select the interval to update the standby screen. If you select the interval to automatically-update the page displayed as the standby screen from among “ 24時間/12時間/8時間/4時間/2時間/1時間/30分/ 更新しない ” (24 hours/12 hours/8 hours/4 hours/2 hours/1 hour/30 minutes/no update), and press c (OK), then “ 待受指定警告表示 ” (Standby Assignment Warning Display) appears.
Smart Mode Be e p !! Smart Mode lets you limit operations to the telephone function, address book, camera, e-mail, C-mail, EZweb, and other frequently used functions, which simplifies operations. Entering Smart Mode While the standby screen is displayed, press c, use a to select “Settings,” and then press c (OK). Press 5 (User Support), 3 (OperationSupport), and then 3 (Mode Setup). Press 2 (Smart Mode). Smart Mode ◎ The lock No. is required when changing from Teens Mode to Smart Mode.
Exiting Smart Mode While the standby screen is displayed, press c. Use j to select “SETTINGS,” and then press c (Select). Press 0 (SmartModeOFF). Press 1 (Yes). This returns to Usual Mode.
Using the Smart Mode Main Menu Smart Mode has its own main menu. You can switch between the two available Smart Mode main menu styles by pressing & (Switch).
Adding Data to the Address Book in Smart Mode While the standby screen is displayed, press &, press 2 (Register), and then press c (Fix). Enter the name, and then press c (OK). To input text → “Inputting Characters” (page 34) Check the reading of the name you inputted, press c (OK), and then press 3 (Input by Myself). You can also select data in incoming records or outgoing records. To go without saving the telephone number, press 4 (Not Input) and perform step 5.
Press 3 (Input by Myself). You can also select data in sending records or receiving records. To go without saving e-mail address, press 4 (Not Input) and perform step 7. Enter the e-mail address, and then press c (OK). To input an e-mail address → “Inputting an E-mail Address” (page 35) Press 2 (Not Register). The confirmation screen appears. Press c (OK). Press c (Reg). “E-Mail Add1,” and “Image” data into an address book record.
Using the Address Book in Smart Mode Example: To view a record in address book While the standby screen is displayed, press & , and then press 1 (Look). Use a to select the address book record you want to view, and then press c (Select). Press 4 (Read Data). The address book record appears. Use j to select the phone number, and press c (Call). You can make a phone call or start Hello Messenger. Use j to select the e-mail address, and press c (E-Mail). You can create an e-mail message.
Creating and Sending E-mail Messages in Smart Mode Bee p p Bee Beep While the standby screen is displayed, press L, 1 (E-Mail), and then 1 (Create Mail). Press 1 (Address Book), use a to select an addressee, and then press c (Select) twice. You can select an addresses from sending/receiving records, or you can manually enter an address.
Enter the body text, and then press c (OK). To input text → “Inputting Characters” (page 34) Press 3 (Not Attach). The confirmation screen appears. Press c (OK). 1 (Data Folder): You can select a photo saved in the Data Folder and attach it to the email message. 2(microSD): You can select a photo saved in the microSDTM memory card and attach it to the e-mail message. In Smart Mode, an e-mail message can have only one attachment. After checking the content of the e-mail, press c (Send).
Shooting a Photo in Smart Mode Clic k! While the standby screen is displayed, press c, use j to select “CAMERA,” and then press c (Select). Press 1 (Photo), and then press 1 (Photo1). Photo 1 Photo 2 Photo 3 Wallpaper 240×320 WideWallpaper 240× 400 VGA 640×480 Point the lens at the subject, and then press c (Shutter). The phone will emit a shutter sound. You can also press b in place of c. Press & (Save).
Viewing Photos in Smart Mode While the standby screen is displayed, press c, use j to select “DATA FOLDER,” and then press c (Select). Press 1 (Data Folder). Use j to select “Photo Folder,” and then press c (Select). Selecting “All Data” displays a list of all photos in the Photo Folder. Use j to select the dated (by shooting date) folder, and then press c (Select). A list of all photos that were shot on that day are displayed.
Use a to select the photo you want to view, and then press c (Menu). Press 1 (Play). The photo appears. 2 (Delete): Deletes data. 3(Attach E-Mail): Displays a screen for composing an e-mail message with an attachment. To create an e-mail message → Perform the procedure starting from step 2 under “Creating and Sending E-mail Messages in Smart Mode” (page 95). 4(MoveTo microSD): Moves the data to microSDTM memory card. 5 (Send via Ir): Sends your data via infrared.
Teens Mode Teens Mode can be used to block spam, and to block inadvertent access to phone numbers and URLs included inside mail messages. Teens Mode can also be used to restrict call time and the number of sending mail. Using Teens Mode ■ Teens Mode can be used to restrict mail reception and display contents. When the sender is a Pair partner Receipt is allowed. When the sender is included in the address book Receipt is allowed.
Turning on Teens Mode While the standby screen is displayed, press c, use a to select “Settings,” and then press c (OK). Press 5 (User Support), and then 3 (OperationSupport). Press 3 (Mode Setup), and then 3 (Teens Mode). Press 1 (Switch TeensMode), and enter the lock No., and press c (OK). Teens Mode The lock No. is required when changing from Teens Mode to Usual Mode or Smart Mode.
Other Functions Security Setup Features With Security Setup, you can make a phone call to preregistered numbers or use high-volume buzzer just holding down 0 for about one second. Safety Buzzer You can use W43CA as high-volume emergency buzzer by holding down 0 for about one second while the standby screen is displayed. ■ To turn on Safety Buzzer While the standby screen is displayed, press c5351, input the lock No., and then press c (OK).
While connected with Casio round-type earphone jack conversion adaptor 01 and MDR-E0931 by SONY/Casio flat-type stereo earphones 03 (option)/ flat-type stereo earphone-microphone (option), Safety Buzzer sounds through W43CA speaker. Extension Mode Using the extension mode, W43CA automatically shuts down the radio wave after issuing the Low Battery Alert. This is quite a useful function that you can still check Outgoing/Incoming Records, Content of e-mail, Address Book, Schedule and so on when necessary.
In addition to the functions covered in this Basic Manual, your W43CA also has the following features. Global Expert EZ apps (BREW®) W43CA supports Global Expert based on au IC card. Global Expert is an international roaming service for the customers to use the phone replacing its au IC card with GSM cellphone for overseas use. No special application procedure or daily/monthly fee are needed, and the call charge is added up to domestic call, so the pay procedure is simple.
Troubleshooting Symptom The phone does not turn on. I can’t make calls. I can’t receive calls. What to check What to do Page Is the battery pack installed correctly ? Correctly install the battery pack. Is the battery pack charged ? Charge the battery pack. P.12 Are you holding down F for at least 2.5 seconds ? Hold down F for at least 2.5 seconds to turn on the phone. P.14 Is (Out of Range) on the display ? Wait until you are in a location is not displayed before where trying to make a call.
If you lose your W43CA Turning on Remote Auto Lock makes it possible for you to set Auto Lock and FeliCa Lock on from a remote location. These lock function keeps others from using your W43CA. Auto Lock OK! ■ Configuring Remote Auto Lock Settings You can set Auto Lock and FeliCa Lock on by making calls several times from the registered phone number to your W43CA within the specified period of time. While the standby screen is displayed, press c413, input the lock No., and then press c (OK).
Press 1 (ON/OFF Setup), and then press 1 (ON). Press 2 (Specified Time), input the period you want to specify, and then press c (OK). You can set the time period (the time intervals from the first call to the last call you should make to activate Remote Auto Lock). You can set the time period between 1 to 10 minutes. Press 3 (Num of Incoming), input the number of calls you want to specify, and then press c (OK). You can set how many times you should repeat making a call to activate Remote Auto Lock.
Index A Address Book ................................... Adding outgoing or incoming record data to the address book ............. Dialing from the address book ........ Editing ............................................. Registering an address book .......... Adjusting the earpiece volume during a call ................................... Adjusting the ring tone volume ....... 38 41 42 40 38 31 30 B Battery level ...................................... 14 Battery pack .................................
Mail filter ......................................... 5, 52 Main menu .................................... 20, 91 Manner Mode Turning on ....................................... 31 Vibrator ............................................ 31 microSDTM memory card ............. 11, 19 Mind your manners! ........................... 1 Movie Movie Folder ................................... 64 Recording a movie .......................... 62 Rerecording a movie ....................... 63 Sending a movie by e-mail ....
For inquiries, call: au Customer Service Center (General Information) From EZweb site: How to access 5 5 7 5 6 or EZ → Top Menu →お客さまサポート (au Customer Support) →お問い合わせ (Inquiries) ※Menu structure is subject to change without notice. From regular phones: フリーコール 0077-7-111 (toll free) From au cellphones: 157area code not required (toll free) Pressing "zero" will connect you to an operator, after calling "157" on your au cellphone.