User manual - MIDI_074H_E_1206A

ManualsBrandsCasio ManualsMusical InstrumentWK-7600

CTK-6200/CTK-6300/CTK-7200/CTK-7300

WK-6600/WK-7600

MIDI Implementation

CASIO COMPUTER CO., LTD.

Contents

I MIDI Message Overview 8

1 Product Conﬁguration as a MIDI Device 8

1.1 System Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.2 Performance Controller Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.3 Sound Generator Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Timbre Type Speciﬁc Operation 10

3 Controlling Send/Receive of MIDI Messages in Each Instrument Part 10

4 Conditions that Disable Message Send and Receive 10

II Channel Message 11

5 Receive Channel 11

6 Send Channel 11

7 Note Oﬀ 11

8 Note On 11

9 Polyphonic Key Pressure 11

10 Control Change 12

10.1 Bank Select (00H,20H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10.2 Modulation (01H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10.3 Data Entry (06H,26H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10.4 Volume (07H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Summary of content (83 pages)

PAGE 1
CTK-6200/CTK-6300/CTK-7200/CTK-7300 WK-6600/WK-7600 MIDI Implementation CASIO COMPUTER CO., LTD. Contents I MIDI Message Overview 1 8 Product Conﬁguration as a MIDI Device 8 1.1 System Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.2 Performance Controller Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.3 Sound Generator Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
10.5 Pan (0AH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 10.6 Expression (0BH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 10.7 General Use Controllers 1 through 8 (10H through 13H, 50H through 53H) . . . . . . . . 14 10.8 Hold1 (40H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 10.9 Sostenuto (42H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
11.6 Mono (7EH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 11.7 Poly (7FH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 12 Program Change 30 13 Channel After Touch 30 14 Pitch Bend 31 III System Message 32 15 Timing Clock 32 16 Start 32 17 Stop 32 18 Active Sensing 32 19 System Exclusive Message 32 19.1 Universal Real Time System Exclusive Message . . . . . . . . . . . . . . . . . .
PAGE 4
24 System Parameters 56 24.1 System Information Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 24.2 System Exclusive Protocol Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 24.3 Data Management Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Patch Parameter 59 25.1 Analog Input Tune Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 25.2 Card Audio Parameter . . . . . . . .
PAGE 5
33 DSP Type List 64 33.1 Single DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 33.2 Dual DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 DSP Parameter Set Type 65 34.1 Wah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 34.2 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 34.3 Distortion . .
PAGE 6
34.36 Chorus Reﬂection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 34.37 Chorus Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 34.38 Flanger Reﬂection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 34.39 Flanger Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 34.40 Reﬂection Distortion . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
IX 36 MIDI Implementation Notation 82 Value Notation 82 36.1 Hexadecimal Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 36.2 Binary Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
Part I MIDI Message Overview 1 Product Conﬁguration as a MIDI Device As a MIDI device, this Instrument consists of the System Section, Sound Generator Section, and Performance Controller Section described below. Each of these sections can send and receive speciﬁc MIDI Messages in accordance with its function. 1.1 System Section The System Section manages the Instrument status and user data.
PAGE 9
1.3.2 Instrument Part Block The instrument part section consists of a total of 32 instrument parts, divided into two groups, named Group A and Group B of 16 instruments each. Each part can perform operations and setting changes using the Instrument mixer function, and/or channel messages and Instrument’s system exclusive messages. Only Group B can be controlled by external channel messages.
PAGE 10
2 Timbre Type Speciﬁc Operation The sound source operation performed for a sound generator instrument receive message may depend on the value of the Timbre Type (see “About the Timbre Type” in “12 Program Change”) of each part’s operation mode. For details, see the explanation for each message. 3 Controlling Send/Receive of MIDI Messages in Each Instrument Part Send/receive of MIDI messages in each instrument part can be enabled/disabled by the Instrument’s mixer, the NRPN message explained under “10.
PAGE 11
Part II Channel Message 5 Receive Channel The channel number of the channel message received by each part is shown in the table under “1.3.2 Instrument Part Block”. 6 Send Channel Basically, the MIDI channel of the channel message sent when the Instrument is played coincides with the MIDI channel of the part being played. Note, however, that the MIDI channel of the performance information that corresponds to the keyboard main part depends on the Keyboard Channel setting value.
PAGE 12
Message Format: n: kk: vv: AnH kkH vvH MIDI Channel Number Key Number Pressure Value Send This message is not sent by this Instrument. Receive This message is not received by this Instrument. 10 Control Change Message Format: n: cc: vv: BnH ccH vvH MIDI Channel Number Control Number Value Send Sent when the Instrument’s pedal is operated or when Instrument settings are changed. Receive Receipt changes the pedal and other performance conditions, and Instrument settings.
PAGE 13
10.1 Bank Select (00H,20H) Message Format: n: mm: ll: : Note1 BnH 00H mmH (MSB) BnH 20H llH (LSB) MIDI Channel Number MSB Value(Note1) LSB Value(Send:00H, Receive:Ignored) For details about the relationship between the MSB value and the tone, see the Tone List that comes with the Instrument. Send Sent when a tone is selected. Receive Receipt causes a change in the tone bank number stored in Instrument memory, but the tone is not actually changed until a Program Change message is received.
PAGE 14
Send Sent when the volume of any part is changed. Receive Receipt changes the volume of the corresponding part. 10.5 Pan (0AH) Message Format: n: vv: Note1 : BnH 0AH vvH MIDI Channel Number Value(Note1) For information about the relationship between setting values and send/receive values, see “35.4 Pan Setting Value Table” in “VIII Setting Values and Send/Receive Values”. Send Sent when the pan of any part is changed. Receive Receipt changes the pan of the corresponding part. 10.
PAGE 15
Receive Receipt changes the value of DSP Parameter 7 [1 to 8] (7-bit parameter) assigned to the part speciﬁed by the MIDI Channel Number. Any message received that corresponds to the parameter of a number not being used by the currently selected DSP is ignored. For details about Parameter 7 of each DSP, see the explanations under “VII DSP Parameter List”. Received values and parameter setting values The range of the value of each DSP Parameter 7 array element depends on the selected DSP or array number.
PAGE 16
: Note1 For information about the relationship between setting values and send/receive values, see the “35.1 Oﬀ/On Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when a pedal that has a sostenuto function is operated. Receive Receipt performs an operation equivalent to a sostenuto pedal operation. 10.
PAGE 17
10.13 Release Time (48H) Message Format: n: vv: : Note1 BnH 48H vvH MIDI Channel Number Value (Note1) For information about the relationship between setting values and send/receive values, see the “35.2 –64 - 0 - +63 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when the release time setting is conﬁgured. Receive Receipt makes a relative change in the time it takes for a note to decay to zero after a key is released. 10.
PAGE 18
: Note1 For information about the relationship between setting values and send/receive values, see the “35.10 Drawbar Position Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when a drawbar 4’ is operated. Receive Receipt changes the drawbar 4’ position. 10.
PAGE 19
10.20 Vibrato Rate (4CH) Message Format: n: vv: : Note1 BnH 4CH vvH MIDI Channel Number Value (Note1) For information about the relationship between setting values and send/receive values, see the “35.2 –64 - 0 - +63 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when the vibrato rate setting is conﬁgured. Receive Receipt changes the note vibrato rate. 10.
PAGE 20
: Note1 For information about the relationship between setting values and send/receive values, see the “35.10 Drawbar Position Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when a drawbar 1 1/3’ is operated. Receive Receipt changes the drawbar 1 1/3’ position. 10.
PAGE 21
10.27 Note Drawbar Organ 2nd Percussion(54H)(Drawbar tone selected) : This message is valid only when a drawbar tone is selected for the MIDI channel. Message Format: vv n: vv: : Note1 BnH 54H vvH MIDI Channel Number Value (Note1) For information about the relationship between setting values and send/receive values, see the “35.1 Oﬀ/On Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when the 2nd percussion button is operated.
PAGE 22
: Note1 For information about the relationship between setting values and send/receive values, see the “35.1 Oﬀ/On Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send This message is not sent by this Instrument. Receive Receipt changes the drawbar parameter key on click. 10.31 Note Drawbar Organ Key Oﬀ Click(58H)(Drawbar tone selected) : This message is valid only when a drawbar tone is selected for the MIDI channel.
PAGE 23
Receive Receipt changes the degree of pitch modulation. 10.34 Reverb Send (5BH) Message Format: n: vv: BnH 5BH vvH MIDI Channel Number Value Send Sent when the reverb send of any part is changed. Receive Receipt changes the reverb send of the corresponding part. 10.35 Chorus Send (5DH) Message Format: n: vv: BnH 5DH vvH MIDI Channel Number Value Send Sent when the chorus send of any part is changed. Receive Receipt changes the chorus send of the corresponding part. 10.
PAGE 24
10.36.2 DSP Enable Message Format: n: mm: ll: Note1 : BnH 62H 01H BnH 63H 02H BnH 06H mmH BnH 26H llH MIDI Channel Number Value (Note1) (Send:00H, Receive:Ignored) For information about the relationship between setting values and send/receive values, see the “35.1 Oﬀ/On Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when each part’s DSP Line On/Oﬀ operation is performed. Receive Receipt changes the DSP on/oﬀ setting of the corresponding part. 10.36.
PAGE 25
Note1 ff 00 01 02 03 04 05 06 07 08 : The following shows the relationship between the Drawbar Foot value and the actual foot bar. Foot Bar Ft16’ Ft5 1/3’ Ft8’ Ft4’ Ft2 2/3’ Ft2’ Ft1 3/5’ Ft1 1/3’ Ft1’ Note2 : For information about the relationship between setting values and send/receive values, see the “35.10 Drawbar Position Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when a drawbar is operated (CTK-7200, CTK-7300, WK-7600 only).
PAGE 26
Send Sent when the 2nd percussion button is operated (CTK-7200, CTK-7300, WK-7600 only). Receive Receipt changes the drawbar parameter 2nd percussion (CTK-7200, CTK-7300, WK-7600 only). 10.36.7 Drawbar Organ 3rd Percussion Message Format: n: mm: ll: Note1 : BnH 62H 0BH BnH 63H 40H BnH 06H mmH BnH 26H llH MIDI Channel Number Value (Note1) (Send:00H, Receive:Ignored) For information about the relationship between setting values and send/receive values, see the “35.
PAGE 27
Note1 : For information about the relationship between setting values and send/receive values, see the “35.11 Nor- mal/Vintage Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send This message is not sent by this Instrument. Receive Receipt changes the drawbar parameter type (CTK-7200, CTK-7300, WK-7600 only). 10.37 RPN (64H,65H) Message Format: n: ll: mm: 10.37.
PAGE 28
10.37.3 Coarse Tune Message Format: n: mm: ll: BnH 64H 02H BnH 65H 00H BnH 06H mmH BnH 26H llH MIDI Channel Number MSB Value(28H - 58H) LSB Value(Not sent, Receive:Ignored) Send Sent when the coarse tune of any part is changed. Receive Receipt changes the coarse tune of the corresponding part. Does not aﬀect sound source operation when the Timbre Type (see “About the Timbre Type” in “12 Program Change”) is Drum. 10.37.
PAGE 29
11.3 All Notes Oﬀ (7BH) Message Format: n: BnH 7BH 00H MIDI Channel Number Send Sent when MIDI send related settings are changed. Receive Receipt releases (key release) all voices that are sounding. 11.4 Omni Oﬀ (7CH) Message Format: n: BnH 7CH 00H MIDI Channel Number Send This message is not sent by this Instrument. Receive Receipt performs the same operation as when All Notes Oﬀ is received. 11.
PAGE 30
12 Program Change Message Format: n: pp: Note1 : CnH ppH MIDI Channel Number Program Number (Note1) For details about the relationship between the program number and the tone, see the Tone List that comes with the Instrument. Send Sent when a tone is selected. Receive Receipt changes the ton of the corresponding part. The selected tone is determined by the program value of this message and the Bank Select message value received prior to this message.
PAGE 31
14 Pitch Bend Message Format: n: ll: mm: EnH llH mmH MIDI Channel Number Value LSB Value MSB Send Sent when the bender is operated. Receive Receipt changes the pitch of the currently sounding note. The range of the pitch change depends on the Bend Range value setting.
PAGE 32
Part III System Message 15 Timing Clock Message Format: F8H Send Sent when auto accompaniment is used. Receive This message is not received by this Instrument. 16 Start Message Format: FAH Send Sent when auto accompaniment is used. Receive This message is not received by this Instrument. 17 Stop Message Format: FCH Send Sent when auto accompaniment is used. Receive This message is not received by this Instrument.
PAGE 33
19.1 Universal Real Time System Exclusive Message Message Format: 19.1.1 F0H 7FH....F7H Master Volume Message Format: ll: mm: F0H 7FH 7FH 04H 01H llH mmH F7H LSB Value(Send:00H, Receive:Ignored) MSB Value Send Sent when the Master Volume is changed. Receive Receipt changes the Master Volume. 19.1.
PAGE 34
Receive Receipt changes the Patch Master Coarse Tune parameter. 19.1.5 Reverb Type Message Format: vv: Note1 : F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 01H 00H vvH F7H Value(Note1) For information about the relationship between setting values and send/receive values, see “35.7 Reverb Type Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Send Sent when the Reverb Type is changed. Receive Receipt changes the Reverb Type. 19.1.
PAGE 35
19.1.9 Scale/Octave 2 Byte Real Time Tuning Message Format: ff: gg: hh: ss tt ...: Note1 : F0H 7FH 7FH 08H 09H ffH ggH Channel Byte 1 (bits 0 to 1 Channel Byte 2 (bits 0 to 6 Channel Byte 3 (bits 0 to 6 Tuning offset(Note1) hhH ssH ttH ... F7H = channel 15 to 16) = channel 8 to 14) = channel 1 to 7) For information about the relationship between setting values and send/receive values, see “35.6 Scale Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document.
PAGE 36
Receive Receipt performs the same operation as when the GM System On message is received. 19.2 Instrument-Speciﬁc System Exclusive Message Message Format: F0H 44H 16H 02H ... F7H This message can be used to send the Instrument memory status, for two-way transfer of special operation commands and user data, to perform sound source parameter operations, etc. For more information, see “IV Instrument-Speciﬁc System Exclusive Messages”.
PAGE 37
Part IV Instrument-Speciﬁc System Exclusive Messages 20 Format This section explains the format of the Instrument-speciﬁc System Exclusive Messages. See “V Parameter List” and “VI Parameter Set List” for information about how parameter sets actually are transferred. 20.1 Message Classiﬁcations Basically, the operation that corresponds to Instrument-speciﬁc system exclusive messages is parameter data transfer.
PAGE 38
The table below shows the body format for each action of Instrument-speciﬁc system exclusive messages. An actual message consists of the items indicated by Y, from left to right. IPR IPS OBR OBS HBR HBS EXI SBS ACK RJC ESS EBS ERR 20.3 20.3.
PAGE 39
20.3.5 act : Action Format: 0aaaaaaaB This ﬁeld indicates the operation of the Instrument-speciﬁc System Exclusive Message.
PAGE 40
SBS:Start of Bulk Dump Session This message is sent to both devices to start a session to transfer a series of parameter sets using one-way protocol or handshake protocol. The protocol used during the session and the data transfer direction is determined in accordance with the value of the data ﬁeld. For details, see the explanation about the data ﬁeld. When there is a request to start a handshake protocol session, the devices that receive this message return ACK after setting up to enable a session.
PAGE 41
20.3.7 mem : Memory Area ID Format: 0mmmmmmmB Speciﬁes the memory area that is the object of the parameter transfer. The following are deﬁned for this Instrument. mem 0 1 2 20.3.8 Data Type User area Preset area Store area Meaning Read/write enabled Read/write disabled Read/write enabled pset : Parameter Set Number Format: LSB MSB 0nnnnnnnB 0mmmmmmmB This ﬁeld is a 2-byte (LSB, MSB) value indicating the number of the parameter set (mmmmmmmnnnnnnnB, Binary) being transferred. 20.3.
PAGE 42
2-dimension array block [index1][index0] Value 00jjjjjjjiiiiiiiB 00lllllllkkkkkkkB 00nnnnnnnmmmmmmmB 00pppppppoooooooB Meaning 0000H 0000H index1 index0 3-dimension array block [index2][index1][index0] Value 00jjjjjjjiiiiiiiB 00lllllllkkkkkkkB 00nnnnnnnmmmmmmmB 00pppppppoooooooB Meaning 0000H index2 index1 index0 4-dimension array block [index3][index2][index1][index0] Value 00jjjjjjjiiiiiiiB 00lllllllkkkkkkkB 00nnnnnnnmmmmmmmB 00pppppppoooooooB 20.3.
PAGE 43
Bulk Parameter Set Transfer The value of this ﬁeld speciﬁes the size of the parameter set memory image stored in the img ﬁeld. Data length indicates the number of bytes of data included within a packet. When this value is zero, it means the data itself does not exist. 20.3.
PAGE 44
• Data = 3 : Start HBS Session Start session to send data using handshake protocol. If a device that receives this message accepts the session, it needs to return ACK. ERR (Error) Format: 0eeeeeeeB The relationship between the data value and error 0eeeeeeeB is deﬁned as shown below. • Data = 0 : Time Out Error This error message is generated when a preset amount of time elapses without a receiving device receiving an expected message.
PAGE 45
Table 1 Memory data 00: Memory data 01: Memory data 02: : Memory data 32: 7 [00.7] [01.7] [02.7] 6 [00.6] [01.6] [02.6] 5 [00.5] [01.5] [02.5] 4 [00.4] [01.4] [02.4] 3 [00.3] [01.3] [02.3] 2 [00.2] [01.2] [02.2] 1 [00.1] [01.1] [02.1] 0 [00.0] [01.0] [02.0] [32.7] [32.6] [32.5] [32.4] [32.3] [32.2] [32.1] [32.0] (Bit M of the NNth byte is indicated at [NN.M].) Table 2 Send data 00: Send data 01: Send data 02: : Send data 37: 7 0 0 0 6 [00.6] [01.5] [02.4] 5 [00.5] [01.4] [02.3] 4 [00.
PAGE 46
20.3.16 EOX : End of System Exclusive Message Format: 11110111B (F7H) This is the End of System Exclusive Message status byte established by the MIDI standard. 21 Individual Parameter Operations There are two parameter unit operations: Individual Parameter Transfer and Individual Parameter Request.
PAGE 47
Session “One session” refers to a series of processes that occur for one user operation. One subsession or multiple subsessions make up a session. The sender sends EBS (End of Bulk Dump Session) to end a session. Regardless of whether there is a single parameter set or multiple parameter sets being transferred, a bulk dump always takes the form of a session, never a subsession only. 22.
PAGE 48
22.2.
PAGE 49
it resends the last data sent. If the correct message does not arrive after a preset number of retries, RJC is sent and the session is terminated. The number of retries is determined in accordance with the parameters described under “24.2 System Exclusive Protocol Parameter”. 22.3.4 Message CRC Error Processing The message receive device returns ERR (CRC Error) if it discovers an illegal format in the received message.
PAGE 50
Data Receiver (External Device) SBS(HBR) -----> <---------> ACK HBR <---------> <---------> <---------> : Send Other Packet : -----> <----- HBS ACK ACK ACK ACK HBS HBS ESS EBS HBS ESS Operation Session Start Request Acknowledge Send Request (Start Sub Session) Send Packet Acknowledge Send Packet Acknowledge Send Packet Acknowledge Acknowledge End Data (End Sub Session) End of Session Example: Data send to Instrument from external device Data Sender (External Device) SBS(HBS) HBS HBS : Ot
PAGE 51
22.3.
PAGE 52
Data Receiver (External Device) SBS(HBR) HBR ACK ERR(Format Error) ACK ACK ACK Data Sender (This Instrument) -----> <---------> <---------> <-???-----> <-----???-> <-----???-> <---------> <----: Note1 : Note2 : ACK HBS HBS HBS ERR(Format Error) ERR(Format Error) HBS Operation Session Start Request Acknowledge Send Request (Optional) Send Packet Acknowledge Send Packet (Note1) Format Error Resend Packet Acknowledge Format Error Acknowledge 2 consecutive format errors(*Note2) Acknowledge Send Packe
PAGE 53
Note : Number of retries that exceeds the retries stipulated by Handshake Max Retry explained under “24.2 System Exclusive Protocol Parameter”. 22.3.
PAGE 54
Data Sender (External Device) SBS(HBS) HBS HBS HBS 22.3.15 Data Receiver (This Instrument) -----> <---------> <---------> <---------> <----- Operation Session Start Request Acknowledge Send Packet Acknowledge Send Packet Acknowledge Send Packet Terminate Session ACK ACK ACK RJC Example: Session Pause Session ﬂow when the session is temporarily paused for some reason and then restarted is shown below.
PAGE 55
Note2 : The sessions can be paused by sending RJC here.
PAGE 56
Part V Parameter List This section explains the parameters that actually can be transferred by the Instrument. 23 Using the Parameter List • Parameter ﬁeld Shows the parameter name. • ID ﬁeld Shows the parameter ID as a hexadecimal number. • R/W ﬁeld Shows “R” to indicate that an IPR (Individual Parameter Request) read operation (Read) is possible or “W” to indicate that an IPS (Individual Parameter Send) write operation is possible. • Block ﬁeld Shows the bit ﬁeld allocation of the block number.
PAGE 57
24.2 System Exclusive Protocol Parameter These parameters are related to the System Exclusive message protocol.
PAGE 58
Parameter Ps Category ID R/W Block Size Array 0019 W 00000000 7 01 Min-Def-Max 00-00-7F Ps Memory 001A W ↑ 7 01 00-00-7F Ps Number 001B W ↑ 14 01 0000-0001-3FFF Ps Data Type 001C R ↑ 8 01 00-00-FF Current Ps Existence 001D R ↑ 1 01 00-00-01 Current Ps Protect 001E R ↑ 1 01 00-00-01 Current Ps Size 001F R ↑ 32 01 00000000-00000000-FFFFFFFF Current Sub Ps Size 0020 R ↑ 32 01 00000000-00000000-FFFFFFFF Current Ps Name 0021 R ↑ 8 10 00-20-7F Max Ps Size
PAGE 59
25 Patch Parameter The main function of patch parameters is to conﬁgure the settings of the sound source of a device. 25.1 Analog Input Tune Parameter These parameters are for analog input tuning. They correspond to the MIC part of the Instrument’s mixer function (CTK-6200, CTK-6300, WK-6600) or to the EXT part (CTK-7200, CTK-7300, WK7600). Parameter Part Enable ID R/W Block Size Array Min-Def-Max Description 0074 R/W 00000000 1 01 00-01-01 0...Off 1...On Line Select 0075 R/W ↑ 1 01 00-00-01 0...
PAGE 60
25.5 Master Tune Parameter These parameters conﬁgure the Master Tuning settings. Parameter ID R/W Block Size Array Min-Def-Max Description Master Fine Tune 0000 R/W 00000000 10 01 0000-0200-03FF -100 - 0 - +99.8(cent)(1unit=100/512cent) Master Coarse Tune 0001 R/W ↑ 7 01 28-40-58 -24 - 0 - +24(semitone) 25.6 Master Mixer Parameter These parameters conﬁgure the Master settings of the mixer. Parameter Master Volume Master Pan Master Line Select Master Eq 25.
PAGE 61
Parameter Position Percussion ID R/W Block Size Array Min-Def-Max Description 001E R/W 3-0:Select Bar 4 01 00-00-08 0-8 001F R/W 00000000 2 01 00-00-03 0...off 1...2nd 2...3rd 3...2nd+3rd Percussion Decay Time 0020 R/W ↑ 7 01 00-00-7F 0-127 Keyon Click 0023 R/W ↑ 1 01 00-00-01 0...off 1...on Keyoff Click 0024 R/W ↑ 1 01 00-00-01 0...off 1...on Type 0022 R/W ↑ 1 01 00-00-01 0...Normal 1...Vintage 26.2 Tone Parameter These parameters conﬁgure settings of tone basic settings.
PAGE 62
Parameter Name Rev Send Algorithm ID 0000 0001 0002 R/W R/W R/W R/W Parameter7 0003 R/W Rotary Sw Onoff 0004 R/W Block 00000000 ↑ ↑ Size Array Min-Def-Max 7 10 00-20-7F 7 01 00-28-7F 14 01 0000-000A-3FFF ↑ ↑ Parameter Index 0005 R/W 0:Button Selection On Value Off Value Note1 28 28.1 0006 R/W 0007 R/W : ↑ ↑ 7 1 08 01 00-40-7F 00-00-01 4 01 00-00-08 7 7 01 01 00-00-7F 00-00-7F Description Ascii Character 0 - 127 ID (Note1) 0 - 127 0...Off 1...On 0.....No Assign 1-8...
PAGE 63
Part VI Parameter Set List This section explains actually how parameter sets can be transferred by the Instrument with bulk dump. 32 Parameter Set Table Field Contents • cat ﬁeld Shows the category value.(Note1) • mem ﬁeld Shows the memory area ID value.(Note1) • pset ﬁeld Shows the parameter set number value. Applicable parameter set numbers are those in the user area where the top number is zero, and are not the same numbers as those displayed by the Instrument. (Note1) Note1 32.
PAGE 64
Part VII DSP Parameter List 33 DSP Type List This is a list of DSP types built into the Instrument. 33.
PAGE 65
33.2 Dual DSP Number 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 20 31 32 33 34 35 36 37 38 39 30 41 42 43 44 45 46 34 34.
PAGE 66
Note1 : For information about the relationship between setting values and send/receive values, see “35.17 LFO Wave Form1 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.2 Compressor Parameter Number Parameter7[1] Parameter7[2] Parameter7[3] Parameter7[4] 34.
PAGE 67
Note1 : For information about the relationship between setting values and send/receive values, see “35.18 LFO Wave Form2 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 68
Note1 : For information about the relationship between setting values and send/receive values, see “35.21 Reﬂection Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 69
Note3 : For information about the relationship between setting values and send/receive values, see “35.13 0-5 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. Note4 : For information about the relationship between setting values and send/receive values, see “35.12 0-3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 70
Parameter Number Parameter7[1] Parameter7[2] Parameter7[3] Parameter7[4] Parameter7[5] Parameter7[6] Note1 : Parameter Name WahWvform Wah Rate Wah Depth FlnWvform Fln Rate Fln Depth Value 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F Notes Note1 Note2 For information about the relationship between setting values and send/receive values, see “35.17 LFO Wave Form1 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document.
PAGE 71
Note2 : For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 72
34.27 Compressor Tremolo Parameter Number Parameter7[1] Parameter7[2] Parameter7[3] Parameter7[4] Parameter7[5] Note1 : Parameter Name CmpThresh Cmp Level TrmWvform Trm Rate Trm Depth Value 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F Notes Note1 For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 73
Note1 : For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 74
Note1 : For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 75
34.41 Reﬂection Chorus Parameter Number Parameter7[1] Parameter7[2] Parameter7[3] Parameter7[4] Note1 : Parameter Name Ref Fbk ChoWvform Cho Rate Cho Depth Value 00 - 7F 00 - 7F 00 - 7F 00 - 7F Notes Note1 For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document. 34.
PAGE 76
34.45 Tremolo Flanger Parameter Number Parameter7[1] Parameter7[2] Parameter7[3] Parameter7[4] Parameter7[5] Parameter7[6] Note1 : Parameter Name TrmWvform Trm Rate Trm Depth FlnWvform Fln Rate Fln Depth Value 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F 00 - 7F Notes Note1 Note2 For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3 Setting Value Table” in “VIII Setting Values and Send/Receive Values” of this document.
PAGE 77
Part VIII Setting Values and Send/ Receive Values 35 35.1 Setting Value Tables Oﬀ/On Setting Value Table Transmit Value 00H 7FH 35.2 Parameter -64 : 0 : +63 Receive Value 00H - 3FH 40H - 7FH Parameter + Pan Setting Value Table Transmit Value 00H : 40H : 7FH 35.5 Receive Value 00H : 40H : 7FH –/+ Setting Value Table Transmit Value 00H 7FH 35.4 Parameter Off On –64 - 0 - +63 Setting Value Table Transmit Value 00H : 40H : 7FH 35.
PAGE 78
Transmit Value (LSB, MSB) (43H, 00H) (65H, 00H) (07H, 01H) (29H, 01H) : (40H, 3FH) (60H, 3FH) (00H, 40H) (20H, 40H) (40H, 40H) : (54H, 7EH) (73H, 7EH) (11H, 7FH) (30H, 7FH) 35.6 35.7 : 00H) 00H) 01H) 01H) - (5FH, (7FH, (1FH, (3FH, 00H) 00H) 01H) 01H) 3FH) 3FH) 3FH) 40H) 40H) - (4FH, (6FH, (1FH, (3FH, (5FH, 3FH) 3FH) 40H) 40H) 40H) 7EH) 7EH) 7FH) 7FH) - (6FH, (0FH, (2FH, (7FH, 7EH) 7FH) 7FH) 7FH) 415.5 415.6 415.7 415.8 : 439.8 439.9 440.0 440.1 440.2 : 465.6 465.7 465.8 465.
PAGE 79
Transmit Value - 35.9 Parameter Chorus 1 Chorus 2 Chorus 3 Chorus 4 Chorus 5 Receive Value 00H - 0EH 0FH - 1CH 1DH - 2AH 2BH - 38H 39H - 47H 48H - 55H 56H - 63H 64H - 71H 72H - 7FH Parameter 0 1 2 3 4 5 6 7 8 Normal/Vintage Setting Value Table Transmit Value 00H 7FH 35.12 Receive Value 00H 01H 02H 03H 04H Drawbar Position Setting Value Table Transmit Value 0H 0FH 1DH 2BH 39H 48H 56H 64H 72H 35.
PAGE 80
35.13 0-5 Setting Value Table Transmit Value 00H 19H 33H 4CH 66H 7FH 35.14 Parameter 0 1 2 3 4 5 Receive Value 00H - 3FH 40H - 7FH Parameter determined by Delay Time determined by Delay Time and Ratio L/R Receive Value 00H - 1FH 20H - 3FH 40H - 5FH 60H - 7FH Parameter off sin tri random LFO Wave Form2 Setting Value Table Transmit Value 00H 40H 7FH 35.
PAGE 81
35.20 LoFi Noise Level Setting Value Table Transmit Value 00H 19H 33H 4CH 66H 7FH 35.21 Parameter 1 2 3 4 5 6 7 8 Receive Value 00H - 29H 2AH - 54H 55H - 7FH Parameter ring modulated signal only ring modulated signal and input signal ring modulated signal and input signal, applied chorus effect Rotate/Brake Setting Value Table Transmit Value 00H 7FH 35.
PAGE 82
Part IX MIDI Implementation Notation 36 36.1 Value Notation Hexadecimal Notation MIDI implementation sometimes requires that data be expressed in hexadecimal format. Hexadecimal values are indicated by the letter “H” after the value. The hexadecimal equivalents of decimal values 10 through 15 are expressed as the letters A through F. The table below shows the hexadecimal equivalents for decimal values 0 through 127, which are often used in MIDI messages.
PAGE 83
Decimal 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 : 125 126 127 Hexadecimal 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H : 7DH 7EH 7FH Binary 00000000B 00000001B 00000010B 00000011B 00000100B 00000101B 00000110B 00000111B 00001000B 00001001B 00001010B 00001011B 00001100B 00001101B 00001110B 00001111B 00010000B 01111101B 01111110B 01111111B 83