IN DATA PROJECTOR XJ-V1/XJ-V2 English Setup Guide z Be sure to keep all user documentation handy for future reference. z To obtain the latest version of this manual visit the website at the URL below. https://world.casio.
Contents Safety Precautions ....................................IN-1 Quick Guide ............................................. IN-13 Operating Precautions ..............................IN-6 Specifications .......................................... IN-14 General Guide ..........................................IN-12 Unpacking As you unpack the projector, check to make sure that all of the items listed below are present.
Safety Precautions Thank you for selecting this CASIO product. Be sure to read these “Safety Precautions” before trying to use it. After reading this User’s Guide, keep it in a safe place for future reference. About safety symbols Various symbols are used in this User’s Guide and on the product itself to ensure safe use, and to protect you and others against the risk of injury and against material damage. The meaning of each of the symbols is explained below.
Safety Precautions ● Power cord + ● Water and foreign matter Misuse of the power cord creates the risk of fire and electric shock. Make sure that you always observe the following precautions. • Be sure to use only the accessories that come with the projector. • Make sure that you use a power source with the same voltage as that specified for the projector. • Do not overload a power outlet with too many devices. • Do not locate the power cord near a stove.
Safety Precautions ● Disposal by burning - ● Exhaust vents Never try to dispose of the projector by burning it. Doing so can cause an explosion, which creates the risk of fire and personal injury. ● Projector light emission - • Never look directly into the lens, intake vents, or exhaust vents while the light is on. When turning on the projector, check to make sure that no one is looking directly into its lens, intake vents, or exhaust vents.
Safety Precautions ● Lightening During a lightening storm, do not touch the plug of the projector’s power cord. ● Remote controller ! + Never try to take the remote controller apart or modify it in any way. Doing so creates the risk of electric shock, burn injury, and other personal injury. Be sure to leave all internal inspection, adjustment, and repair up to your original dealer or authorized CASIO service center. Never allow the remote controller to become wet.
Safety Precautions Battery Precautions Magnetism * Danger * Caution + Should liquid leaking from an alkaline battery get into the eyes, immediately take the following steps. 1. Do not rub the eyes! Wash the eyes with clean water. 2. Contact a physician immediately. Failure to take immediate action can lead to loss of eyesight. * Warning Misuse of batteries can cause them to leak and stain the area around them, or to explode, creating the risk of fire and personal injury.
Operating Precautions About the Light Source Unit The projector’s light source unit uses a laser and LED. The life of the light source unit is rated at approximately 20,000 hours. The actual life will depend on use conditions, the settings configured on the setup menu, and differences between each individual light source unit. The light source unit is warranted for the period noted on the warranty certificate or for 6,000 hours, whichever comes first.
Operating Precautions Label Bottom Vent Outlets • Vent outlets become very hot during projection. Never touch vents or allow them to become blocked. • Do not insert foreign objects.
Operating Precautions Projector Light Emission • Never block light output while the light is on. • Never look directly into the lens while the light is on. Particular care is required when children are present. Projection Lamp Caution This label is a “RISK GROUP 2” caution label required under the IEC62471 standard. RISK GROUP 2 (Moderate Risk) lamps exceed the limits of Exempt Group (No Hazard) standards. Do not stare at the operating lamp during projection. Doing so may be harmful to the eyes.
Operating Precautions Other Precautions This projector is made of precision components. Failure to observe the following precautions can result in inability to correctly save data and malfunction. ● Never use or store the projector in the following locations. Doing so creates the risk of malfunction of and damage to the projector.
Operating Precautions ● Keystone Correction and Image Quality Performing keystone correction causes the image to be compressed before it is projected. This can result distortion of the image or a loss of image quality. If this happens, change orientation of the projector and/or screen so it conforms as much as possible to the illustration under “Setting Up the Projector” in the User’s Guide.
Operating Precautions Precaution when Handling the Projector after Use The projector’s exhaust vents and the area around the vents become very hot during operation, and will still be hot immediately after turning off the projector. Because of this, you should hold the sides of the projector as shown in the illustration whenever moving it. Cleaning the Projector Periodically clean the projector exterior, lens, intake vents, and exhaust vents on a regular basis.
General Guide [INPUT] key [ON/Stand-by P] key POWER/STANDBY indicator Exhaust vents STATUS indicator Intake vents Remote control signal receiver Zoom ring Intake vents Focus ring Projection lens HDMI terminal COMPUTER terminal AUDIO OUT terminal AUDIO IN terminal Power connector Remote control signal receiver SERIAL port SERVICE port Anti-theft lock hole* * The anti-theft lock hole is provided for connection of an anti-theft chain. Visit the Kensington Lock Website at https://www.kensington.
Quick Guide This section explains the operational flow up to the point that projection is started. For more individual operations, see the “User’s Guide” (UsersGuide.pdf). 1. Load batteries into the remote controller. ☞ “To load remote controller batteries” (User’s Guide) 2. Place the projector onto a table, desk, or stand that is level and firm, making sure that you allow enough room around it.
Specifications If you run into problems... If you experience any problems while operating the projector or if you suspect that the projector is not operating properly, refer to the “Troubleshooting” section in the “User’s Guide” (UsersGuide.pdf). Specifications Model Name XJ-V1 Display Chip XJ-V2 DLP® chip × 1, DLP® system Display system Chip Size XGA 1.40cm (0.55") diagonal (Aspect ratio: 4:3) Number of Pixels 786,432 (1024 × 768) Projection Lens 1.1X manual zoom, manual focus F 2.4-2.
Specifications Model Name Power Consumption (100 to 240V) XJ-V1 XJ-V2 Eco Level 1 when Eco Mode is “On” 120W 130W Eco Level 5 when Eco Mode is “On” 70W 75W When “Bright” is selected for Eco Off Mode 150W 165W When “Normal” is selected for Eco Off Mode 135W 140W Standby Power Consumption Approximate Dimensions 100 to 120V: 0.12W 220 to 240V: 0.23W 269.5 (W) × 269.5 (D) × 88.5 (H) mm (10.6" × 10.6" × 3.5") (Including projections) Approximate Weight 2.8kg (6.
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Manufacturer: CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union: Casio Europe GmbH Casio-Platz 1, 22848 Norderstedt, Germany www.casio-europe.
MA2008-B