xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Information in this document is subject to change without notice. © 2011 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Information in this document is subject to change without notice. © 2011 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide TABLE OF CONTENTS Intended Readers ....................................................................................................................................................... 4 Typographical Conventions ........................................................................................................................................................ 4 Notes, Notices, and Cautions ............................
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide INTENDED READERS Typographical Conventions Notes, Notices, and Cautions Safety Instructions Safety Cautions General Precautions for Rack-Mountable Products Protecting Against Electrostatic Discharge The DES-3200 Series Hardware Installation Guide contains information for setup and management of the Switch. The term, “the Switch” will be used when referring to all switches in the series.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide SAFETY INSTRUCTIONS Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential damage. Throughout this document, the caution icon ( that you need to review and follow. ) is used to indicate cautions and precautions SAFETY CAUTIONS To reduce the risk of bodily injury, electrical shock, fire, or damage to the equipment, observe the following precautions.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide • Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modifications. Always follow your local/national wiring rules. • When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe the following guidelines: o Install the power supply before connecting the power cable to the power supply.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide PROTECTING AGAINST ELECTROSTATIC DISCHARGE Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as the microprocessor. You can do so by periodically touching an unpainted metal surface on the chassis.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide CHAPTER 1 INTRODUCTION Switch Description Ports LED Indicators Front-Panel Description Rear Panel Description Side Panel Description Gigabit Combo Ports SWITCH DESCRIPTION The DES-3200-10, DES-3200-18, DES-3200-26, DES-3200-28, and the DES-3200-28F are all members of the DLink Switch family.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide PORTS The following table lists the ports that are present within each switch: DES-3200-10 Ver. A1: Eight 10/100BASE-TX Ports Two 1000BASE-T/SFP Combo Ports One female DCE RS-232 DB-9 console port DES-3200-10 Ver. B1: Eight 10/100BASE-TX Ports One SFP Port One 1000BASE-T/SFP Combo Port One RJ-45 Console Port DES-3200-18 Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide The following table lists the features and compatibility for each type of port present in the DES-320010/18/26/28/28F. 10/100/1000BASE-T: IEEE 802.3 compliant IEEE 802.3u compliant IEEE 802.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide LED INDICATORS The Switch supports LED indicators for Power, Console, and Link/Act/Speed. The following shows the LED indicators for the five DES-3200 Series switches along with an explanation of each indicator. Figure 1- 1. LED Indicators on DES-3200-10 Ver. A1 Switch Figure 1- 2. LED Indicators on DES-3200-10 Ver. B1 Switch Figure 1- 3. LED Indicators on DES-3200-18 Ver. A1 Switch Figure 1- 4.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-7. LED Indicators on DES-3200-28 Ver. A1 Switch Figure 1- 8. LED Indicators on DES-3200-28 Ver. B1 Switch Figure 1- 9. LED Indicators on DES-3200-28F Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Per Device: LED Indicative Color Status Description Power Green Solid Light Power ON Light off Power OFF Solid Light Console on. Blinking This LED will blink green during the Power-On Self Test (POST). Light off Console off. Console Green DES-3200-10/18/26/28 Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide LED Per GE Port: LED Indicative Color Status Description Link/Act/Speed mode for 1000BASE-T ports Green/Amber Solid Green When there is a secure 1000Mbps connection (or link) at any of the ports. Blinking Green When there is reception or transmission (i.e. Activity-Act) of data occurring at a 1000Mbps connected port.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide FRONT-PANEL DESCRIPTION DES-3200-10 Ver. A1: • Eight 10/100Mbps BASE-T ports • Two Combo 1000BASE-T/SFP ports located to the right • One female DCE RS-232 DB-9 console port • LEDs for Power, Console, Link/Act/Speed for each port Figure 1- 10. Front Panel of the DES-3200-10 Ver. A1 DES-3200-10 Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-18 Ver. B1: • Sixteen 10/100 BASE-TX Ports • One SFP Port • One 1000BASE-T/SFP Combo Port • One RJ-45 Console Port • LEDs for Power, Console, Link/Act/Speed for each port Figure 1-13. Front Panel of the DES-3200-18 Ver. B1 DES-3200-26 Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-28 Ver. B1: • Twenty-four 10/100Mbps BASE-T ports • Two SFP ports located to the right • Two Combo 1000BASE-T/SFP ports located to the right • One RJ-45 Console Port • LEDs for Power, Console, Link/Act/Speed for each port Figure 1- 17. Front Panel of the DES-3200-28 Ver. B1 DES-3200-28F Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide REAR PANEL DESCRIPTION The rear panel of the Switch contains an AC power connector. The AC power connector is a standard three-pronged connector that supports the power cord. Plug-in the female connector of the provided power cord into this socket, and the male side of the cord into a power outlet. The Switch automatically adjusts its power setting to any supply voltage in the range from 100 ~ 240 VAC at 50 ~ 60 Hz.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1- 17. Rear panel view of the DES-3200-28 Ver. A1 Figure 1- 18. Rear panel view of the DES-3200-28 Ver. B1 Figure 1- 19. Rear panel view of the DES-3200-28F Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide SIDE PANEL DESCRIPTION The left- and right-hand panels of the Switch have heat vents to dissipate heat. Do not block these openings, and leave at least 6 inches of space at the rear and sides of the Switch for proper ventilation. Be reminded that without proper heat dissipation and air circulation, system components might overheat, which could lead to system failure Figure 1-20. Side panels of the DES-3200-10 Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1- 23. Side panels of the DES-3200-26 Ver. A1, DES-3200-26 Ver. B1 and DES-3200-28 Ver. B1 Figure 1-24. Side panels of the DES-3200-28F Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide GIGABIT COMBO PORTS Each of the five switches in the DES-3200 Series features either two or four Gigabit Ethernet Combo ports. These ports are 1000BASE-T copper ports (provided) and Mini-GBIC ports (optional). See the diagram below to view the two Mini-GBIC port modules being plugged into the Switch. Please note that although these two front panel modules can be used simultaneously, the ports must be different.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1- 27. Installing the Mini-GBIC Module The Switch is equipped with SFP (Small Form Factor Portable) ports, which are to be used with fiber-optical transceiver cabling in order to uplink various other networking devices for a gigabit link that may span great distances.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide CHAPTER 2 INSTALLATION Package Contents Before You Connect to the Network Installing the Switch without the Rack Installing the Switch in a Rack Mounting the Switch in a Standard 19” Rack Power On AC Power Power Failure PACKAGE CONTENTS Open the shipping carton of the Switch and carefully unpack its contents.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide INSTALLING THE SWITCH WITHOUT THE RACK When installing the Switch on a desktop or shelf, the rubber feet included with the Switch should first be attached. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilation space between the Switch and any other objects in the vicinity. Figure 2- 1.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide MOUNTING THE SWITCH IN A STANDARD 19" RACK CAUTION: Installing systems in a rack without the front and side stabilizers installed could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances. Therefore, always install the stabilizers before installing components in the rack.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide CHAPTER 3 CONNECTING THE SWITCH Switch to End Node Switch to Hub or Switch NOTE: All 10/100/1000Mbps NWay Ethernet ports can support both MDI-II and MDI-X connections. SWITCH TO END NODE End nodes include PCs outfitted with a 10, 100 or 1000 Mbps RJ 45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, or 5 UTP/STP cable.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 3- 3. DES-3200-28F Ver. A1 connected to an end node The Link/Act LEDs for each UTP port will light green or amber when the link is valid. A blinking LED indicates packet activity on that port.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide SWITCH TO HUB OR SWITCH These connections can be accomplished in a number of ways using a normal cable. • A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4 or 5 UTP/STP cable. • A 100BASE-TX hub or switch can be connected to the Switch via a twisted-pair Category 5 UTP/STP cable. • A 1000BASE-T switch can be connected to the Switch via a twisted pair Category 5e UTP/STP cable.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide CHAPTER 4 INTRODUCTION TO SWITCH MANAGEMENT Management Options Web-based Management Interface SNMP-Based Management Connecting the Console Port (RS-232 DCE / RJ-45) First Time Connecting to the Switch Password Protection SNMP Settings IP Address Assignment MANAGEMENT OPTIONS This system may be managed out-of-band through the console port on the front panel or in-band using Telnet.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide To connect a terminal to the console port: Ver. A1 models Connect the female connector of the RS-232 cable directly to the console port on the Switch, and tighten the captive retaining screws. Connect the other end of the cable to a terminal or to the serial connector of a computer running terminal emulation software. Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-28 Fast Ethernet Switch Command Line Interface Firmware: Build 1.28.005 Copyright(C) 2010 D-Link Corporation. All rights reserved. UserName: Figure 4- 1. Initial screen after first connection FIRST TIME CONNECTING TO THE SWITCH The Switch supports user-based security that can allow you to prevent unauthorized users from accessing the Switch or changing its settings. This section tells how to log onto the Switch.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide To create an administrator-level account for the Switch, follow these steps: • At the CLI login prompt, enter create account admin followed by the and press the Enter key. • The switch will then prompt the user for a password. Type the used for the administrator account being created and press the Enter key. • Again, the user will be prompted to enter the same password again to verify it.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide The default community strings for the Switch used for SNMP v.1 and v.2 management access are: • public - Allows authorized management stations to retrieve MIB objects. • private - Allows authorized management stations to retrieve and modify MIB objects. SNMP v.3 uses a more sophisticated authentication process that is separated into two parts.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-28:4#show switch Command: show switch Device Type MAC Address IP Address VLAN Name Subnet Mask Default Gateway Boot PROM Version Firmware Version Hardware Version System Name System Location System Uptime System Contact Spanning Tree GVRP IGMP Snooping VLAN Trunk 802.1X Telnet Web RMON SSH CTRL+C ESC q Quit : DES-3200-28 Fast Ethernet Switch : 00-63-32-28-01-01 : 10.81.17.4 (Manual) : default : 255.0.0.0 : 0.0.0.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-28:4#config ipif System ipaddress 10.90.90.91/255.0.0.0 Command: config ipif System ipaddress 10.90.90.91/8 Success. DES-3200-28:4# Figure 4- 5. Assigning the Switch an IP Address In the above example, the Switch was assigned an IP address of 10.90.90.91 with a subnet mask of 255.0.0.0. (the CIDR form was used to set the address (10.90.90.91/8).
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide CHAPTER 5 WEB-BASED SWITCH CONFIGURATION Introduction Login to Web manager Web-Based User Interface INTRODUCTION All software functions of the Switch can be managed, configured and monitored via the embedded web-based (HTML) interface. The Switch can be managed from remote stations anywhere on the network through a standard browser such as Firefox or Microsoft Internet Explorer.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide WEB-BASED USER INTERFACE The user interface provides access to various Switch configuration and management windows, allows you to view performance statistics, and permits you to graphically monitor the system status. AREAS OF THE USER INTERFACE The figure below shows the user interface. The user interface is divided into three distinct areas as described in the table. Area 2 Area 1 Area 3 Figure 5- 2.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide WEB PAGES When you connect to the management mode of the Switch with a Web browser, a login window is displayed. Enter a user name and password to access the Switch's management mode.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide APPENDIX A – TECHNICAL SPECIFICATIONS General Protocols IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3z 1000BASE-T (SFP “Mini GBIC”) IEEE 802.1D Spanning Tree IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1Q VLAN IEEE 802.1p Priority Queues IEEE 802.1X Port Based Network Access Control IEEE 802.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-18 Ver. B1:16 x 10/100Mbps + 1 SFP Port + 1 Combo 1000BASE-T/SFP Port DES-3200-26 Ver. A1: 24 x 10/100Mbps + 2 Combo 1000BASE-T/SFP Ports DES-3200-26 Ver. B1: 24 x 10/100Mbps + 2 Combo 1000BASE-T/SFP Ports DES-3200-28 Ver. A1: 24 x 10/100Mbps + 4 Combo 1000BASE-T/SFP Ports DES-3200-28 Ver. B1: 24 x 10/100Mbps + 2 Combo 1000BASE-T/SFP Ports + 2 SFP Ports DES-3200-28F Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-26 Ver. B1: 441(W) x 207(D) x 44(H) mm DES-3200-28 Ver. A1: 441(W) x 207(D) x 44(H) mm DES-3200-28 Ver. B1: 441(W) x 207(D) x 44(H) mm DES-3200-28F Ver. A1: 441(W) x 207(D) x 44(H) mm Weight DES-3200-10 Ver. A1: 1.46kg DES-3200-10 Ver. B1: 1.17kg DES-3200-18 Ver. A1: 1.50kg DES-3200-18 Ver. B1: 1.22kg DES-3200-26 Ver. A1: 2.28kg DES-3200-26 Ver. B1: 2.14kg DES-3200-28 Ver. A1: 2.40kg DES-3200-28 Ver. B1: 2.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide LED Indicators: Location LED Indicative Color Power Green Per Device Console DES-320010/18/26/28 Ver. A1 LED Per 10/100 Mbps Port DES-320010/18/26/28 Ver. B1 LED Per 10/100 Mbps Port DES-3200-28F Ver.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide ports Appendix A – Technical Specifications Blinking Green When there is reception or transmission (i.e. Activity--Act) of data occurring at a 1000Mbps connected port. Solid Amber When there is a secure 100Mbps connection (or link) at any of the ports. Blinking Amber When there is reception or transmission (i.e. Activity—Act) of data occurring at the ports. Light off No link.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide APPENDIX B – CABLES AND CONNECTORS ETHERNET CABLE When connecting the Switch to another switch, a bridge or hub, a normal cable is necessary. Please review these products for matching cable pin assignment. The following diagrams and tables show the standard RJ-45 receptacle/connector and their pin assignments. Figure B- 1.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide CONSOLE CABLE When connecting the Switch a PC, a Console cable is necessary. The following diagrams and tables show the standard Console-to-DJ-45 receptacle/connector and their pin assignments. Figure B- 2.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide APPENDIX C – MODULE SPECS AND CABLE LENGTHS Use the following table to as a guide for the module specs and maximum cable lengths.
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this lifetime product warranty for hardware: Only for products purchased, delivered and used within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO, and; Only with proof of purchase.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
Product Registration Register your D-Link product online at http://support.dlink.com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Tech Support Technical Support You can find software updates and user documentation on the DLink website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the service period, and warranty confirmation service, during the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.
Technical Support United Kingdom (Mon-Fri) Home Wireless/Broadband 0871 873 3000 (9.00am–06.00pm, Sat 10.00am-02.00pm) Managed, Smart, & Wireless Switches, or Firewalls 0871 873 0909 (09.00am – 05.30pm) (BT 10ppm, other carriers may vary.) Ireland (Mon-Fri) All Products 1890 886 899 (09.00am-06.00pm, Sat 10.00am-02.00pm) €0.05ppm peak, €0.045ppm off peak Times Internet http://www.dlink.co.uk ftp://ftp.dlink.co.uk Technische Unterstützung Deutschland: Österreich: Schweiz: Web: http://www.dlink.
Assistance technique Assistance technique D-Link sur internet :http://www.dlink.fr Assistance technique D-Link par téléphone : 0820 0803 03 0.12 € TTC/min depuis un poste fixe Du lundi au vendredi de 9h à 19h (hors jours fériés) Asistencia Técnica Asistencia Técnica Telefónica de D-Link: +34 902 30 45 45 0,067 €/min De Lunes a Viernes de 9:00 a 19:00 http://www.dlink.es Supporto tecnico Supporto Tecnico dal lunedì al venerdì dalle ore 9.00 alle ore 19.
Pomoc techniczna Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021 Pomoc techniczna firmy D-Link świadczona przez Internet: http://www.dlink.eu/support/ Technická podpora Web: http://www.dlink.cz/support/ E-mail: support@dlink.cz Telefon ČR: +420 211 151 640 nebo SK: +421 (0)692 147 110 Telefonická podpora je v provozu: PO - PÁ od 09:00 do 17:00 Volání je zpoplatněno dle příslušných tarifů Vašeho operátora. Technikai Támogatás Tel.
Teknistä tukea asiakkaille Suomessa: Internetin kautta : http://www.dlink.fi Arkisin klo. 9 - 21 Numerosta : 0600 155 57 Teknisk Support D-Link Teknisk Support via Internet: http://www.dlink.se D-Link Teknisk Support via telefon: 0900-100 77 00 Vardagar 08:00-20:00 Assistência Técnica Assistência Técnica da D-Link na Internet: http://www.dlink.pt e-mail: soporte@dlink.
Tehnička podrška Hvala vam na odabiru D-Link proizvoda. Za dodatne informacije, podršku i upute za korištenje uređaja, molimo vas da posjetite D-Link internetsku stranicu na www.dlink.eu www.dlink.biz/hr Tehnična podpora Zahvaljujemo se vam, ker ste izbrali D-Link proizvod. Za vse nadaljnje informacije, podporo ter navodila za uporabo prosimo obiščite D-Link - ovo spletno stran www.dlink.eu www.dlink.biz/sl Suport tehnic Vă mulţumim pentru alegerea produselor D-Link.
Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Australia: Tel: 1300-766-868 24/7 Technical Support Web: http://www.dlink.com.au E-mail: support@dlink.com.au India: Tel: +91-22-27626600 Toll Free 1800-22-8998 Web: www.dlink.co.in E-Mail: helpdesk@dlink.co.in Singapore, Thailand, Indonesia, Malaysia, Philippines, Vietnam: Singapore - www.dlink.com.sg Thailand - www.dlink.co.th Indonesia - www.dlink.co.id Malaysia - www.dlink.com.
Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Iran Unit 5, 5th Floor, No. 20, 17th Alley , Bokharest St. , Argentine Sq. , Tehran IRAN Postal Code : 1513833817 Tel: +98-21-88880918,19 +98-21-88706653,54 General Inquiries: info.ir@dlink-me.com Tech Support: support.ir@dlink-me.com Morocco M.I.T.C Route de Nouaceur angle RS et CT 1029 Bureau N° 312 ET 337 Casablanca , Maroc Phone : +212 663 72 73 24 Email: support.na@dlink-me.
Техническая поддержка Обновления программного обеспечения и документация доступны на Интернет-сайте D-Link. D-Link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока. Клиенты могут обратиться в группу технической поддержки D-Link по телефону или через Интернет. Техническая поддержка D-Link: +7(495) 744-00-99 Техническая поддержка через Интернет http://www.dlink.ru e-mail: support@dlink.ru Офисы Украина, 04080 г. Киев , ул. Межигорская, 87-А, офис 18 Тел.
SOPORTE TÉCNICO Usted puede encontrar actualizaciones de softwares o firmwares y documentación para usuarios a través de nuestro sitio www.dlinkla.
Suporte Técnico Caso tenha dúvidas na instalação do produto, entre em contato com o Suporte Técnico D-Link por: Chat Online www.dlink.com.br/suporte E-mail suporte@dlink.com.br Back Office backoffice@dlink.com.br * *Acionar Garantia para 4 ou mais equipamentos Telefones São Paulo: (11) 2755-6950 *GO: 4052-1850 (Ligação local) *Nordeste: 0800-7024104 *Demais Estados: 4062-1850 (Ligação local) *Apenas Modems ADSL Garantia diferenciada vendida pela internet.
D-Link 友訊科技 台灣分公司 技術支援資訊 如果您還有任何本使用手冊無法協助您解決的產品相關問題,台灣 地區用戶可以透過我們的網站、電子郵件或電話等方式與D-Link台灣 地區技術支援工程師聯絡。 D-Link 免付費技術諮詢專線 0800-002-615 服務時間:週一至週五,早上9:00到晚上9:00 (不含周六、日及國定假日) 網 站:http://www.dlink.com.tw 電子郵件:dssqa_service@dlink.com.tw 如果您是台灣地區以外的用戶,請參考D-Link網站全球各地 分公司的聯絡資訊以取得相關支援服務。 產品保固期限、台灣區維修據點查詢,請參考以下網頁說明: http://www.dlink.com.
Dukungan Teknis Update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web D-Link. Dukungan Teknis untuk pelanggan: Dukungan Teknis D-Link melalui telepon: Tel: +62-21-5731610 Dukungan Teknis D-Link melalui Internet: Email : support@dlink.co.id Website : http://support.dlink.co.
Technical Support この度は弊社製品をお買い上げいただき、誠にありがとうご ざいます。 下記弊社 Web サイトからユーザ登録及び新製品登録を 行っていただき、ダウンロードサービスにて サポート情報、ファームウェア、ユーザマニュアルを ダウンロードすることができます。 ディーリンクジャパン Web サイト URL:http://www.dlink-jp.
技术支持 办公地址:北京市东城区北三环东路 36 号 环球贸易中心 B 座 26F 02-05 室 邮编: 100013 技术支持中心电话:8008296688/ (028)66052968 技术支持中心传真:(028)85176948 各地维修中心地址请登陆官方网站查询 网址:http://www.dlink.com.
Registration Card All Countries and Regions Excluding USA Print, type or use block letters. Your name: Mr./Ms_____________________________________________________________________________ Organization: ________________________________________________ Dept.