Quick Installation Guide For EBM522 Mesh Wi-Fi Router
EBM522 Mesh Wi-Fi Router Quick Installation Guide Package Contents RJ-45 Cable Quick Installation Guide For EBM 552 M esh Wi-Fi Router EBM522 x 3 QIG Power Adapter x 3 (12V/1.5 A) A quick look at EBM522 Reset Button Press and hold 5 sec(s) Set device to default status. Release when LED indicator become solid amber. Press and hold 10sec(s) Switch device between Controller and Agent mode. Release when LED indicator become flash red and green.
EBM522 Mesh Wi-Fi Router Quick Installation Guide LED Indicators There are two LEDs located on the front panel, providing status information to the user. LED1 Status Description System ready, but Internet is not connected Slowly Flashing Green Internet is connected System working fine Solid Green Wi-Fi signal is good (Agent) Pairing Fast Flashing Green System working but the signal is fair (Agent) Solid Amber Pairing Failed Slowly Flashing red in 1min.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Setting up your EBM522 This chapter describes the proper steps for connecting your Mesh Wi-Fi router. Please be sure to follow the steps below. Step a: Using RJ-45 cable to connect your modem’s LAN port to your device’s WAN port. Step b: Before plugging the AC adapter to both Cable Modem and Mesh Wi-Fi, the sequence of plugging will be Mesh Wi-Fi and then Cable Modem. Please do follow the sequence.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Connecting to the device There is a label pasted to the bottom of EBM522. In that label, you can obtain Wi-Fi access information. Please note, following label is just an example, each EBM522 has its own label and setting value. Please follow your label information to access your EBM522 Mesh Wi-Fi system. You can access the network either by the following methods. a.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Accessing the Web Management For easy-changing the default settings, a Web-based GUI is built-in for your access. Use the following procedures to login to your EBM522. a. Open your web browser, launch the Web GUI address, http://router.castlenet http://router.castlenet b. Then type the Username/Password: admin/admin, and press Enter. Setting up your Mesh system Download the router App to manage your Wi-Fi Mesh home network.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Adding agent to your Mesh Wi-Fi system a. Power ON another device. Wait for a moment, press "Next" when the Status LED becomes solid red. b. Press “Sync” button on both controller and agent device. c. On boarding process may take up several minutes, please wait a moment. d. Congratulations. You may add another agents to the Mesh Wi-Fi system or go to main page. a. b. c. d.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Accessing the App Management Now you can see your Wi-Fi environment information on the app, also configure advanced functions, such as guest network, parental control, QoS, and monitor current traffic flow.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EBM522 Mesh Wi-Fi Router Quick Installation Guide FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Statement This device complies with Class B Part 15 of the FCC Rules. The device generates, uses and can radiate radio frequency energy and, if not installed and used as instructed, may cause harmful interference to radio communication.
EBM522 Mesh Wi-Fi Router Quick Installation Guide Seller may charge Buyer a fee (including travel expenses, if needed) to cover the cost of evaluation if the evaluation shows that the items are not defective or that they are defective for reasons beyond the scope of this warranty.The Seller makes no warranty concerning components or accessories not manufactured by it.
