CASTLES TECHNOLOGY UPT1000F Book 2 User Manual Confidential Version 1.0 Feb. 2021 MAN-UPT1000-02-02-V1.0 Castles Technology Co., Ltd. 6F, No. 207-5, Sec. 3, Beixin Rd., Xindian District, New Taipei City 23143, Taiwan R.O.C. http://www.castech.com.
WARNING Information in this document is subject to change without prior notice. No part of this publication may be reproduced, transmitted, stored in a retrieval system, nor translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior written permission of Castles Technology Co., Ltd. All trademarks mentioned are proprietary of their respective owners. Castles Technology Co., Ltd.
Revision History Version Date Description 1.0 Feb 25,2021 Initial creation. Castles Technology Co., Ltd. Confidential • All Right Reserved. Author Tommy Pg.
Contents 1. Introduction .................................................................................................................. 5 2. Hardware Setup............................................................................................................ 6 2.1. 3. 4. Basic Operation ........................................................................................................... 8 3.1. Program Manager .............................................................................
1. Introduction This document provides a guideline on operating and configuring Castles UPT1000F. The scope of this document includes setting up the UPT1000F, basic operation, application life cycle, and some advance features. Castles Technology Co., Ltd. Confidential • All Right Reserved. Pg.
2. Hardware Setup 2.1. Parts of the UPT1000F Front View Castles Technology Co., Ltd. Confidential • All Right Reserved. Pg.
Rear View Castles Technology Co., Ltd. Confidential • All Right Reserved. Pg.
3. Basic Operation 3.1. Program Manager The UPT1000F is the terminal without keypad. There are two ways to input/control the terminal. One is to connect a USB keyboard to the port of USB2 with USB adapter. Another one is connecting to PC with console, please follow the steps below to connect PC and UPT1000F for controlling. ▪ Power on UPT1000F and connect COM Port 1 to PC. COM Port 1 ▪ Run the application program such as “TeraTerm” or “PuTTY” on PC. ▪ Select “Serial port” to set the com port.
▪ Press any key on keyboard to refresh screen if doesn’t show “Program Manager” on “Tera Term” or PuTTY“. Once the power is on in normal status, UPT1000F will enter Program Manager if no default application selected. All user applications are listed in Program Manager. User can select an application and run the application, view the application info, delete the application, or set application to the default one to run once the power is on. Users may enter System Menu to configure UPT1000F settings.
▪ Press [2] button to delete application. ▪ Press [3] button to view application info. ▪ Press [OK] button to run application. ▪ Press [ ↑ ] or [↓] as the up and down button to select application. Castles Technology Co., Ltd. Confidential • All Right Reserved. Pg.
3.2. System Menu System Menu Page 1 Page 2 System Menu 1.Download AP 2.System Info 3.Memory Status 4.Sys Settings 5.Test Utility 6.Factory Reset 7.Power Off 8.FK PWD Change 9.Share obj Mng System Menu 1.Embedded TMS 2.Font Mng 3.Debug Tools 4.ULD KEY HASH 5.HW Detect 6.Bluetooth Setup 7.Plug-in Mng 8.Key Injection 9.TP Calibration 0:Download 0:Download Page 3 System Menu 1.Key Bridge 2.PWD Change 0:Download ▪ Press [↑] button to previous page. ▪ Press [↓] button to next page.
System Menu (Page 1) System Menu 1.Download AP 2.System Info 3.Memory Status 4.Sys Settings 5.Test Utility 6.Factory Reset 7.Power Off 8.FK PWD Change 9.Share obj Mng 0:Download ▪ Press [1] button to enter Download AP menu: Download user application or kernel modules firmware. ▪ Press [2] button to enter System Info menu: View kernel module firmware information. ▪ Press [3] button to enter Memory Status menu: View terminal flash memory and RAM information.
System Menu (Page 2) System Menu 1.Embedded TMS 2.Font Mng 3.Debug Tools 4.ULD KEY HASH 5.HW Detect 6.Bluetooth Setup 7.Plug-in Mng 8.Key Injection 9.TP Calibration 0:Download ▪ Press [1] button to enter TMS setting menu: TMS (Terminal Management System) setting menu. ▪ Press [2] button to view Font Management: View Font Management. ▪ Press [3] button to enter Debug Tools menu: Get core dump or debug log. ▪ Press [4] button to view hash value: View ULD user key hash value.
System Menu (Page 3) System Menu 1.Key Bridge 2.PWD Change 0:Download ▪ Press [1] button to enter key bridge menu: Support key injection for specific software. ▪ Press [2] button to enter PWD Change menu: Change the password of Function key, PMEnter key and Factory key Castles Technology Co., Ltd. Confidential • All Right Reserved. Pg.
4. Technical Notes 4.1. Serial Cable PIN Assignment PIN Description No Name 1 NC 2 NC 3 NC 4 NC 5 GND 6 NC 7 TX Output Please connect to Host RS232 Level RX 8 RX Input Please connect to Host RS232 Level TX Castles Technology Co., Ltd. Type Description GND Confidential • All Right Reserved. Pg.
5. Appendix 5.1. FCC Warning Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
