User Manual C20E Walk-Behind Corded Auto Floor Scrubber, 20" Cleaning Path Model 641745 GLOBALINDUSTRIAL.
C20E Model 641745 WARNINGS PLEASE READ THE INSTRUCTIONS CAREFULLY PRIOR TO USING THIS PRODUCT. WARNING - to reduce the risk of fire, electrical shock, and/or injury/damage to persons or property: • • • • • • • • • • • • • • • • • • • DO NOT operate the machine unless trained and authorized. This unit must be plugged into a 3-prong grounded outlet. DO NOT use flammable materials in the tank or as a cleaning agent in the machine. DO NOT use the machine to clean up flammable or combustible spills.
C20E Model 641745 TECHNICAL SPECIFICATIONS Cleaning width Squeegee width Work capacity Brush pressure Brush RPM Brush motor Suction motor Solution tank Recovery tank Machine dimensions(Excluding squeegee) Packing size Cord Total Weight (Machine and Charger) Model # 262000 262001 20” 30.7” 18800sq.ft/hr. 99.2lbs 180 120V/375W/6.25Amp/60HZ 120V/1200W/10Amp/60HZ 11.9 gallon 14.53 gallon 46” x 21.5“ x 38.39 “(L x W x H) 50.47” x 26” x 45.67”(L x W x H) 12AWG ST Cord, 82ft with GFCI plug 253 lbs.
C20E Model 641745 MACHINE COMPONENTS 9 1 15 3 2 14 4 10 5 6 16 18 11 13 12 19 20 21 7 17 8 1) 2) 3) 4) 5) 6) 7) 8) Recovery tank cover Body/Solution Tank Solution Tank Cap Head Assembly Rubber Skirt Pad Driver/Brush Solution Tank Filter Water Flow Lever 9) Recovery Tank Drain 10) Water Level Indicator 11) Power Cord 12) Squeegee Assembly 13) Vacuum hose 14) Head Assembly Pedal 15) Squeegee assembly Lever 16) Pad/Brush ON/OFF button 3 17) ON/OFF Key 18) Vacuum ON/OFF button 19) Vacuum hole
C20E Model 641745 MACHINE SET UP Package Contents: 1) Machine 2) Squeegee Assembly 3) Pad Driver/Brush Machine Set-up/Operation Prior to each use: 1) Always plug into grounded outlet rated 120V/60Hz. 2) Check that squeegee assembly is properly installed. 3) Check that Pad Driver is properly installed. 4) Ensure the working surface can support the weight of the machine. 5) Always close Recovery Tank cover fully before use.
C20E Model 641745 SQUEEGEE ASSEMBLY INSTALLATION 1) Disconnect the power. 2) Loosen the 2 knobs on the squeegee assembly. 3) Connect the vacuum hose to the vacuum hole in the squeegee assembly. 4) Align the knobs with the slots and tighten the knobs. Knobs PAD DRIVER/BRUSH INSTALLATION WARNING - The Pad Driver has sharp hook and loop-type surface grips for attaching scrubbing pads. Wear leather work gloves while setting up the Pad Driver/Brush.
C20E Model 641745 SOLUTION TANK Water Level Indicator Remove the solution tank cap and fill with clean water for regular cleaning. Contact Global Industrial (1-800-645-1232) for recommendations on proper cleaning solutions for dirtier surfaces. Check water level indicator for water level. SQUEEGEE RUBBER BLADE REPLACEMENT Remove the squeegee assembly from the unit (refer to squeegee assembly installations). Unlock the spring lock and slide out the blades. Replace with new blades and re-assemble.
C20E Model 641745 OPERATION WARNING - Ensure scrubbing pads are attached before using the pad driver to avoid scratching the floor. 1) Turn the Key to the ON position. 2) Lower the Pad Driver/Brush Head Assembly to the floor by stepping on the Head Assembly Foot Pedal, guiding the pedal to the left, and letting it rise up to disengage it. Remove your foot from the pedal. 3) Lower the Squeegee Assembly by lowering the squeegee assembly lever. 4) Press the Vacuum ON/OFF button to turn on the Vacuum.
C20E Model 641745 DAILY MAINTENANCE WARNING Before performing any maintenance on the machine, make sure that the power is turned off or the batteries are disconnected. Repairs are to be completed by authorized service centers only. 1) Wipe the whole machine with clean/damp cloth. WARNING – Check local regulations for properly disposing wastes before emptying tanks.
C20E Model 641745 TROUBLESHOOTING Problem No Power Little or no solution flow Poor water pickup Cause • Unit not plugged in. • Tripped circuit breaker. Solution • Plug in the unit. • Reset the circuit breaker. • • • • Water flow tap closed. Clogged solution tank filter. Empty solution tank. Squeegee Assembly is not lowered. • • • • • Squeegee clogged. • • • Squeegee blades worn. Squeegee not mounted correctly. • • • Vacuum hoses have a hole or are loose.
C20E Model 641745 Wiring Diagram 10
C20E Model 641745 GLOBAL EQUIPMENT COMPANY INC. FLOOR CARE EQUIPMENT WARRANTY 1. LIMITED WARRANTY Global Equipment Company Inc.
C20E Model 641745 States or Canada. For the avoidance of doubt, this Limited Warranty shall be null and void for any product exported or transported outside the continental United States and Canada.
GLOBALINDUSTRIAL.COM 1-800-645-1232 © 2021 Caterpillar. All rights reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. Global Industrial™ a licensee of Caterpillar Inc.
