Use and Care Manual
10 11
10 11
TROUBLESHOOTING
Common Audio/Visual Problems
Problem Explanation/Recommendation
Buzzing sound in audio
systems
Some inexpensive stereo systems and boom boxes make a buzzing
sound when operated from the inverter, because the power supply in the
electronic device does not properly filter the modified sine wave produced
by the inverter. The only solution to this problem is to use a sound system
that has a higher quality power supply.
Problem: Television
Interference
The inverter is shielded to minimize interference with TV signals. However,
in some instances, some interference may still be visible, especially when
the TV signal is weak. Try the following to improve the picture:
1. Move the Inverter as far away as possible from the TV set, the antenna,
and the antenna cables. Use a short AC extension cord, if necessary.
2. Adjust the orientation of the antenna cables, and the TV power cord to
minimize interference.
3. Make sure that the antenna feeding the TV provides an adequate
(snow-free) signal and that high quality, shielded antenna cable is used.
Common Power Output Problems
Problem Explanation/Recommendation
Input voltage below
10.5 volts
Recharge auto battery or check DC power supply.
Equipment being
operated draws too
much power
• Reduce load to maximum 1000 watts if connected via battery clips.
• Reduce load to maximum 100 watts if connected via the 12V dc
accessory plug.
• Connect directly to power source using the included Battery Clips when
operating above 100 watts.
Inverter in thermal
shutdown condition
Allow inverter to cool down. Ensure there is adequate ventilation around
the unit and that the load does not exceed the maximum wattage.
AC output is shorted
Unplug the AC appliance. Disconnect the unit from any 12 volt DC power
source. Check the appliance cord.
ACCESSORIES
Recommended accessories for use with this unit are available from the manufacturer. If you need
assistance regarding accessories, please contact manufacturer at 855-806-9228 (855-806-9CAT).
WARNING:
The use of any accessory not recommended for use with this appliance could be
hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
manufacturer at 855-806-9228 (855-806-9CAT).
TWO-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of
TWO (2) YEARS from the date of retail purchase by the original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective product can
be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or
replacement at manufacturer’s option. Proof of purchase may be required by manufacturer. (2) Return
the product to the retailer where product was purchased for an exchange (provided that the store is a
participating retailer). Returns to retailer should be made within the time period of the retailer’s return
policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required.
Please check with the retailer for their specific return policy regarding returns that are beyond the time
set for exchanges.
Red (flashing):
A fault condition has occurred. The unit emits three beeps every five seconds, and
the AC and USB outlets are automatically shut down. Refer to the Protective Features Section and the
Troubleshooting Section of this Instruction Manual. Press the On/Off Button to turn the inverter off,
correct the fault and then press the On/Off Button again to turn the inverter back on.
Operation of the 120 Volt AC Outlets
1. Connect the inverter to a functioning 12 volt DC power source as described in this Instruction
Manual. If using the 12 Volt DC Vehicle Accessory Adapter, rotate the vehicle accessory plug slightly
to make sure there is good contact. Make sure there is adequate space for proper ventilation of the
inverter.
2. Press the On/Off Button to turn the unit ON.
3. Depending on the power source, either the 100W LED Indicator or both the 100W and 1000W LED
Indicators will light. If these LEDs do not light or if the power/fault LED flashes red, please refer to
the “Troubleshooting” section of this manual.
4. Plug the (110/120 volt AC) appliance into one of the Inverter’s three-prong AC outlets and operate
normally.
Notes:
Ensure that the wattage of all equipment simultaneously plugged into the inverter does not exceed 100 watts
continuous through the supplied DC Vehicle Adapter plug, and 1000 watts continuous via the supplied Battery Clips
with Slide-In Connectors.
The Inverter will not operate appliances and equipment that generate heat, such as hair dryers, electric blankets,
microwave ovens and toasters.
Remember to disconnect the inverter from any power source when not in use.
Operation of the USB Charging Ports
1. Connect the inverter to a functioning 12 volt DC power source as described in this Instruction
Manual. If using the 12 Volt DC Vehicle Accessory Adapter, rotate the vehicle accessory plug slightly
to make sure there is good contact. Make sure there is adequate space for proper ventilation of the
inverter.
2. Press the On/Off Button to turn the unit ON.
3. Depending on the power source, either the 100W LED Indicator or both the 100W and 1000W LED
Indicators will light. If not, please refer to the “Troubleshooting” section of this manual.
4. Plug the USB-powered device into one of the inverter’s USB Charging Ports and operate normally.
Notes:
Ensure that the wattage of all equipment simultaneously plugged into the inverter does not exceed 100 watts
continuous through the supplied DC Vehicle Adapter plug, and 1000 watts continuous via the supplied Battery Clips
with Slide-In Connectors.
This unit’s USB Charging Ports do not support data communication. They only provide 5 volts/2A DC power each to an
external USB-powered device.
Remember to disconnect the inverter from any power source when not in use.
Not all mobile phones are provided with a charging cable, they are normally data cables which are not supported by
this device - please check with your mobile phone manufacturer for the correct charging cable.
CARE AND MAINTENANCE
Storage
1. Idealstoragetemperaturerangeis 0-40°C (32-104°F).
2. Store and use the CPI1000 in a cool, dry place with adequate ventilation for all-around air
circulation.
3. Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or
dampness.
Fuse Replacement (in Vehicle Accessory Outlet Plug)
If the inverter is overloaded, and the Power/Fault LED is not lit, the internal 12 amp fuse may be blown.
1. Unscrew the flange of the plug (counterclockwise).
2. Remove the end contact, flange and fuse.
3. Inspect the fuse to see if it is good or blown.
4. Replace with a new 12 amp fuse, if needed.
5. Carefully reassemble the fuse, end contact and flange. Do not overtighten the flange (clockwise).
CPI1000_ManualENSP_101713.indd 10-11 10/17/2013 11:22:32 AM