Instructions / Assembly

ManualsBrandsCatalina Creations ManualsOutdoorsOlympus Fire Pit

Assembly and Instruction Sheet

Important!

Please read and follow ALL instructions before assembling or using this

product, particularly the safety statements. Failure to follow instructions

and warnings could result in damage to property, serious injury or death.

Olympus Fireplace

Model: AD218

Tools Required:

• Phillips Head Screwdriver

• Adjustable Wrench

Check all parts for shipping damage:

Call us at (800) 230-6530 or email us: customerservice@asiadirectinc.

net if you have any problems or questions regarding this product.

Part # Quantity Part Description

A 1 Fire Bowl

B 4 Side Panels

C 1 Spark Screen

D 8 Hardware

E 1 Spark Screen Handle

F 1 Storage Cover

G 1 Screen Lifting Tool

H 4 Legs

I 1 Log Grate

• Outdoor use only. Never use in enclosed area. Use in

unventilated areas will endanger your life.

• Do not use this unit on or near combustible surfaces or

structures such as wood decks, dry leaves or grass, vinyl or

wood siding, etc.

• Use on level, non-combustible surface only.

• Keep away from all combustible materials including gasoline

and other ﬂammable liquids and vapors.

• Never use ﬂammable accelerants, such as: gasoline, alcohol,

paint thinners, kerosene, etc. to start a ﬁre. Serious injury or

property damage could result.

• Screen lifting tool may become hot when in use! Failure

to wear protective gloves may lead to injury.

• Always wear ﬁre-resistant gloves when handling hot

metal screen and lifting tool.

• Keep away from house, garage, balconies, or overhangs.

• Avoid using during dry or windy conditions.

• Keep out of reach of children.

• Do not overﬁll or use to burn leaves or trash.

• Exercise the same care you would with an open ﬁre.

• Never leave unit unattended while hot or in use.

• Completely extinguish ﬁre before leaving.

• Ashes can remain hot for a long time after ﬁre is extinguished.

• Dispose of cold ashes properly.

• Any modiﬁcation of the unit will void product warranty.

Contact local authorities regarding possible burn

restrictions before using product.

WARNING!

Assembly Instructions

Step 1:

Carefully unpack all parts. Inspect for missing

parts or damage.

(continued on back)

Parts Check List

Summary of content (4 pages)

PAGE 1
Assembly and Instruction Sheet Parts Check List Olympus Fireplace Model: AD218 Tools Required: • Phillips Head Screwdriver • Adjustable Wrench Part # Quantity A 1 Part Description Fire Bowl B 4 Side Panels C 1 Spark Screen D 8 Hardware E 1 Spark Screen Handle F 1 Storage Cover Important! G 1 Screen Lifting Tool Please read and follow ALL instructions before assembling or using this product, particularly the safety statements.
PAGE 2
Assembly Instructions (cont.) Step 2: Align holes of Side Panel (B) with the holes of Stand Leg (H) making sure curve of the leg is pointed outward. Insert screw through Leg and Side Panel hole. With both screws inserted, align another Side Panel on the opposite side of the Leg forming a corner as shown in (Figure 1). Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Step 3: Secure both Screws with Nuts and hand tighten only at this point (Figure 2). Repeat step until all four legs are in place.
PAGE 3
Manual De Instrucciones Del Dueño Lista de Partes Chimenea Olympus Modelo: AD218 Importante! Por favor lea y siga TODAS las instrucciones antes que empiece a montar este producto, en particular las noticias de seguridad. Fracaso de seguir las instrucciones y los avisos podría resultar en daño a propiedad y herida o muerte.
PAGE 4
Instrucciones De Montaje Paso 2: Alinee los agujeros de un panel lateral con los agujeros de una pierna del soporte. Aseguré que la curva de la pierna está señalada hacia fuera. Inserte los tornillos a través de los agujeros de la pierna y del panel lateral. Alinee otro panel lateral en el lado opuesto para que forme una esquina (Figura 1). Figura 1 Figura 2 Figura 3 Figura 4 Figura 5 Figura 6 Paso 3: Aseguré los tornillos con las tuercas y solamente apriete con la mano (Figura 2).