Instructions / Assembly

Assembly Instructions (cont.)
Step 2:
Place Large Stand Support Ring (F) on ground with screw
holes facing up. Align top holes of Leg (M) with screw holes
of Stand Support Ring. Attach Legs to Stand Support Ring
with screws, HAND TIGHTEN ONLY at this point (Figure 1).
Step 3:
Align holes of Small Stand Support Ring (G) with support
brackets on Legs and fasten with screws (Fig. 2). Once all
stand screws are in place, tighten with screwdriver (Fig. 3).
Turn stand upright and place Fire Bowl (M) and Grates (D).
Step 4:
Attach Spark Screen Sections (A) to Screen Support Rings
(C) with bolts and nuts (Fig 4). Once all four screen sec-
tions are in place, fasten with screwdriver. Place completed
screen assembly over Fire Bowl. There will be a small gap
between the Fire Bowl and screen (Fig. 5). (Note: Do not
attach screen handle on hinged door until you have placed
screen assembly on replace.)
Step 5:
Fasten Screen Handle to Hinged
Screen Door as shown in 5A.
Step 6:
Place Dome Vent (K) on top of Dome Top (B) attach with
bolts and nut (Fig. 6-7). Place Dome Top on completed
stand assembly. Place Dome Vent Screen (J) on in Dome
Vent.
Your replace is now ready for use outside on a level non-
combustible surface.
Please read and follow all Warnings and
safety instructions before using.
Figure 1 Figure 2
Figure 3 Figure 4
Figure 5 Figure 6
Figure 7 Figure 8
• Fire bowl may be cleaned with water and mild detergent.
• Do not use abrasive detergents or pads to clean surround or re bowl.
• As with any outdoor grill, periodic maintenance is required to
return painted steel surfaces to original appearance. Remove any
rust with sandpaper or steel brush and repaint with grill paint suitable
for high-temperature surfaces. Follow manufacturer’s instructions.
General Care
Please contact us if you have any problems or questions regarding this product.
Toll Free: [phone], M-F, 9 a.m. - 5 p.m. EST.
Email: [e-mail]
Customer Service
AD238OM (8/12)
Assembly and Instruction Sheet
Important!
Please read and follow ALL instructions before assembling or using this
product, particularly the safety statements. Failure to follow instructions
and warnings could result in damage to property, serious injury or death.
Dome Fireplace
Model: AD238S
Tools Required:
• Phillips Head Screwdriver
• Adjustable Wrench
Part # Quantity Part Description
A 4 Spark Screen Assembly
B 1 Dome Top
C 2 Screen Support Rings
D 2 Grates
E 1 Hardware
F 1 Large Stand Support Ring
G 1 Small Stand Support Ring
H 2 Door Handle
I 1 Storage Cover
J 1 Dome Vent Screen
K 1 Dome Vent
L 4 Legs
M 1 Fire Bowl
Check all parts for shipping damage:
Call us at [phone] or email us: customerservice@asiadirectinc.
net if you have any problems or questions regarding this product.
• Outdoor use only. Never use in enclosed area. Use in
unventilated areas will endanger your life.
• Do not use this unit on or near combustible surfaces or
structures such as wood or composite decks, dry leaves or
grass, vinyl or wood siding, etc.
• Use on level, non-combustible surface only.
• Keep away from all combustible materials including gasoline
and other ammable liquids and vapors.
• Never use ammable accelerants, such as: gasoline, alcohol,
paint thinners, kerosene, etc. to start a re. Serious injury or
property damage could result.
• Screen lifting tool may become hot when in use! Failure
to wear protective gloves may lead to injury.
• Always wear re-resistant gloves when handling hot
metal screen and lifting tool.
• Keep away from house, garage, balconies, or overhangs.
• Avoid using during dry or windy conditions.
• Keep out of reach of children.
• Do not overll or use to burn leaves or trash.
• Exercise the same care you would with an open re.
• Never leave unit unattended while hot or in use.
• Completely extinguish re before leaving.
• Ashes can remain hot for a long time after re is extinguished.
• Dispose of cold ashes properly.
• Any modication of the unit will void product warranty.
Contact local authorities regarding possible burn
restrictions before using product.
WARNING!
Assembly Instructions
Step 1:
Carefully unpack all parts. Inspect for missing
parts or damage.
Parts Check List
A
B
C
D
F
E
G
H
K
M
I
J
L
Fig. 5A