Installation Guide

ManualsBrandsCatalina Lighting ManualsLighting1.72 ft. 3-Light Brushed Nickel Integrated LED Fixed Track Kit with Bubble Glass Shades

IMPORTANT SAFETY INSTRUCTIONS

3 LIGHT LED FIXED TRACK

For Customer Assistance:

www.luciditylights.com

Made In China

Read and Save:

1. To reduce the chance of fire or electrical shock: Do not install non-factory wiring or any other electrical components.

Altering or modifying the lamp in any way will render the lamp unsafe.

2. Keep curtains, shades, wall hangings and all other fabrics and objects away from the lamp canopy, lamp shade and light

bulb. Unit is not designed to support additional weight. Do not hang objects from the lamp or any lamp part.

3. Before starting the installation, disconnect the power by turning off the circuit breaker or removing the appropriate fuse

at the fuse box. Turning off the power at the light switch is not sufficient to prevent electrical shock.

4. This unit is suitable for damp locations.

5. Electrical Connections: All electrical connections must be in accordance with local codes, ordinances and the National

Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified,

licensed, electrician.

6. This unit is to be mounted to a metal electrical junction box (outlet box) directly supported by the building structure.

7. Tools and Materials Required: (Not Included) Flathead screwdriver, wire cutters, ladder, pliers,

U.L./CSA listed electrical tape.

LIGHT BULB REPLACEMENT

Integrated LED bulb replacement not required.

CLEANING AND MAINTENANCE

1. Clean using a mild cleaning solution and a soft cloth.

2. Never use a rough cloth or chemical cleaners containing acids, abrasives or solvents.

8. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment on and off, the user isencouraged to try to correct the interference

by one or more of the following:

- Reorient or relocate the receiving antenna.

- Increase the separation between the lighting unit and receiver.

- Connect the lighting unit into an outlet on a circuit other than the outlet which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for assistance.

NOTE: Please note that changes and modifcations not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

The party responsible name: Lucidity Lights,Inc.

Address: Boston, MA 02129.

Internet contact information : http://www.luciditylights.com

9. Dimmable to 10% with recommended dimmers: Lutron Diva (DVCL-153PRWH), Lutron Skylark (CTCL-153PDH-WH),

Lutron Toggler (TGCL-153PHWH), Lutron Maestro (MACL-153MH-WH), Lutron Caseta (P-PKG1WWH-R), Leviton Sure Slide

(R62-06674-P0W), Leviton Decora (R12-06672-1LW), Leviton Illume Tech (R50-IPL06-10M), Eaton AL Series (AAL06-C1),

Eaton Sky AL(SAL06P-LA-K).

Summary of content (6 pages)

PAGE 1
3 LIGHT LED FIXED TRACK IMPORTANT SAFETY INSTRUCTIONS Read and Save: 1. To reduce the chance of fire or electrical shock: Do not install non-factory wiring or any other electrical components. Altering or modifying the lamp in any way will render the lamp unsafe. 2. Keep curtains, shades, wall hangings and all other fabrics and objects away from the lamp canopy, lamp shade and light bulb. Unit is not designed to support additional weight. Do not hang objects from the lamp or any lamp part. 3.
PAGE 2
HARDWARE: A 2PCS SCREW (AA) AA BB B 3PCS WIRE CONNECTOR (BB) C ASSEMBLY INSTRUCTIONS 1. Preparing the unit for installation Carefully unpack and lay all parts on a clean, level surface. Unscrew the canopy nuts (C) from fixture assembly (B) and detach the mounting bracket (A). Attach the mounting bracket (A) to the junction box (not included) with junction box screws (AA). 2. Make electrical connections to a 120V AC/60Hz circuit. Lift up the fixture assembly (B) toward the ceiling.
PAGE 3
RIEL FIJO DE 3 LUCES LED INSTRUCCIONES IMPORTANTES DE SEGURIDAD Leer y conservar: 1. Para reducir las posibilidades de incendio o descarga eléctrica: No instale cableado eléctrico u otros componentes eléctricos que no vengan de fábrica con esta lámpara. Si esta lámpara es alterada o modificada, su seguridad se verá comprometida. 2.
PAGE 4
ACCESORIOS DE MONTAJE A AA BB B 2 PZAS TORNILLO (AA) 3 PZAS CONECTOR DE HILOS (BB) C INSTRUCCIONES DE ENSAMBLAJE 1. Préparation de l’unité pour l’installation Desembale con cuidado todas las piezas y colóquelas sobre una superficie limpia y pareja. Destornille las tuercas de la cubierta (C) para quitarlas de la luminaria (B) ysepare el soporte de montaje (A). Ajuste el soporte de montaje (A) a la caja de empalme (no incluida) con los tornillos de la caja de empalme (AA). 2.
PAGE 5
RAIL FIXE DE DEL À 3 LUMIÈRES INSTRUCTIONS DE SÉCURITÉ IMPORTANTES À lire et à conserver: 1. Pour diminuer le risque d’incendie ou de choc électrique : Ne pas utiliser de câbles ou d’autres composants électriques qui ne sont pas du même fabricant. Toute altération ou modification de la lampe peut la rendre non sécuritaire. 2. Garder les rideaux, abat-jours, panneaux muraux, tissus et autres objets éloignés du couvercle de la lampe, de l’abat-jour et de l’interrupteur.
PAGE 6
MATÉRIEL : A AA BB B 2 PCS VIS (AA) 3 PCS CONNECTEUR DE FILS (BB) C INSTRUCTIONS D’ASSEMBLAGE 1. Préparation de l'unité pour l'installation: Déballez soigneusement et posez toutes les pièces sur une surface propre et plane. Dévissez les écrous du couvercle (C) de l'ensemble de luminaire (B) et détachez le support de montage (A). Fixez le support de montage (A) à la boîte de jonction (non fournie) avec les vis de la boîte de jonction (AA). 2.