RECHARGEABLE HEADLIGHT HL-EL6000RC Manual Design Pat. Pending Copyright© 2015 CATEYE Co., Ltd.
COMPONENTS Light unit Helmet mount (Helmet mount HP) FlexTight™ bracket (H-34N HP ) Control unit x3 Battery unit (BA-608) Remote control switch (WSW-001) Fixing strap Auxiliary strap Extension cable Cable cover Rubber band (Large/Small) Battery charger 1
PRECAUTIONS ON USE This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme à la réglementation FCC, partie 15, et aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
HOW TO CHARGE BATTERY UNIT PRECAUTIONS ON CHARGING Always charge the product before use. To AC Power Outlet • If the battery unit is wet, wipe off moisture with a dry cloth before charging the batteries. • Be sure to use only the supplied battery charger (applicable to 100 - 240 volts). The battery charger is indoor use only. Battery charger • Do not leave the battery unit for a long time with the battery charged. • When the operating time decreases significantly, the battery life is close to an end.
HOW TO MOUNT TO A BICYCLE (1/3) PRECAUTIONS WHEN MOUNTING Light unit Remote control switch • Be sure to tighten the dial by hand. When you tighten it too hard with a tool, the screw thread may be stripped. • Round off the cut edge of the bracket strap to prevent injury. Rubber band • Ensure that the frame is clean, and then pull the fixing strap tightly to fix the control unit in place.
HOW TO MOUNT TO A BICYCLE (2/3) 1 2 Bracket 3 Rubber pad Strap Dial 4 5 Light unit Screw Click CAUTION!: Check the dial and screw on the bracket periodically, and use them without any loosening. Release lever To remove the light unit, pull it forward while pulling up the release lever.
HOW TO MOUNT TO A BICYCLE (3/3) 6 Control unit 7 Control unit Position alignment mark Battery unit Unlock Ring Plug Lock Knob Slide Set the knob of the control unit to the “Unlock” position, align the battery unit with the position alignment mark, and then slide the battery unit into place. Connect the plug so that the directions of the arrow and the mark match. To remove the plug, hold the ring, and then pull out the plug.
MOUNTING THE LIGHT UNIT ON A HELMET (1/3) Remote control switch How to handle the battery unit Carry the battery unit in a pocket or bag, with the rubber pad removed. Before doing that, be sure that the cable of the battery unit is properly accommodated.
MOUNTING THE LIGHT UNIT ON A HELMET (2/3) 1 Bracket strap 2 3 Click Light unit Release lever Put the bracket strap through the air vent on the helmet, and secure it firmly. 4 Secure the cable to the backside of the helmet using the auxiliary strap. To remove the light unit, pull it forward while pulling up the release lever.
MOUNTING THE LIGHT UNIT ON A HELMET (3/3) 6 Set the knob of the control unit to the “Unlock” position, align the battery unit with the position alignment mark, and then slide the battery unit into place. Unlock Battery unit Slide Lock Knob CAUTION!: After you connect the battery unit, be sure to set the knob back to the “Lock” position to lock the battery unit in place. To remove the battery unit, set the knob to the “Unlock” position, and then pull out the battery unit.
SWITCH OPERATION Switch (Battery indicator) Approx. 1 hours Approx. 2 hours Approx. 4 hours OFF Press and hold Press and hold *1 Click Click Dynamic Hi Middle (6000 lm) (4000 lm) (2000 lm) Double-click Click Approx. 1 hours Approx. Click 11 hours Approx. 12 hours Approx.
PROTECTION FUNCTIONS REPLACING THE REMOTE CONTROL SWITCH BATTERY Temperature control If the temperature of the light unit increases abnormally while the light is on, the protection circuit will activate, and the lighting mode will be decreased by a level. In this situation, if the light unit temperature decreases, the lighting mode will be returned to its previous level. After you replace the battery, check that the light turns on when you press the remote control switch near the control unit.
SPARE/OPTIONAL PARTS 5343020 5338829N 5341832N 5343040 Light unit FlexTight™ bracket (H-34N HP ) Helmet mount (Helmet mount HP) Control unit 5343030 5343050 5342180 5343080 5342190 Battery unit (BA-608) Fixing strap Auxiliary strap Extension cable Cable cover 5343070 5447010 1603860 Remote control switch (WSW-001) Rubber band Lithium battery (CR1632) 5343060 Battery charger 12
SPECIFICATIONS LIMITED WARRANTY Light source COB LED 2-year Warranty: Light unit / Control unit / Battery unit / Battery charger Battery unit Lithium-ion rechargeable battery BA-608 Li-ion/14.