e p l n a ® o s r r e t u p m o c o l y c c M RE od FE e RE l NC OS E G 1.
Introduction Thank you very much for purchasing the CAT EYE OS 1.1. Read "SETUP GUIDE" first, for the installation and the basic operation of the product. Read this "REFERENCE GUIDE" when you want to know more about the CAT EYE OS 1.1. Important Warning! • Do not give excessive attention to the monitor or the data. Always pay attention to the road, traffic and your surroundings. • Keep this product away from children. If children should use this product, they should have adult supervision.
Buttons MENU button RESTART button Measurement icons START/STOP button (ENTER) REV FWD MODE button (SELECT) See how the four buttons work in the various modes. 1 2 3 4 5 6 7 Elapsed Time icon Trip Distance icon Average Speed icon Maximum Speed icon Total Distance icon Current Speed icon Clock Time icon START/STOP button (ENTER) Normally this button starts and stops timer that effects the other functions like average speed, etc. When measuring, the speed scale icon flashes.
Setup (CLEAR ALL DATA) Before first use or to erase all the stored data (Format operation) To erase all the data stored in the main unit, carry out the format operation. 1. Hold the unit as shown in the figure. PRESS AND HOLD the two MODE/SELECT buttons, press and release RESTART button on the back of the OS. CONTINUE HOLDING DOWN the two MODE/SELECT buttons for TWO MORE SECONDS and let go. Now the FORMAT YES/NO prompt will appear. 2. Select YES and press ENTER/START/STOP button.
Setup (Custom setup) Custom setup To personalize your Cat Eye OS1.1, select YES in Custom setup prompt. Function customizing You can choose to display just the functions you would like. Press ENTER/START/STOP button to select each function you would like to display. You can also simply SELECT ALL to display all seven cyclocomputer functions.
Functions (Spd, Tm, Dst, Av, Mx, Odo) Current Speed Current Speed always displays in the upper display. The data is updated once a second. When the font size is 100%, Current Speed appears between Clock Time and Elapsed Time and is indicated by the flashing Spd icon. 0.0(3.0)-65.9 mph [0.0(4.0)-105.9 km/h] Elapsed Time This is the ride time from the start to the present and shown in hours, minutes and seconds. Performing a reset operation returns the data to zero.
Functions (Clock Time, Countdown, Pace arrow, Eco mode, Auto mode) Clock Time Time is displayed in 12h or 24h mode. If you push the two MODE buttons simultaneously, the date/weekday review screen will be displayed for three seconds. Countdown When the countdown function is on, the remaining distance or time (whichever you have selected), as compared to the time you started measuring, will be displayed. If the measured distance/time exceeds your setting, a negative value will flash.
Functions (Personal data, Battery life) Personal data display On the normal operation screen, if you hold down the two MODE buttons simultaneously for three seconds or longer, the current personal data settings will be displayed for five seconds. If only a NAME or BIRTHDAY has been entered, only that data will be displayed. If no personal data has been entered, the space will be displayed in blank. Battery life indicator If this indicator appears, the battery is beginning to run down.
Menu screen Menu screen When MENU button is pressed, the screen changes from measuring screens to menu screens. Measuring screen Menu screens are divided into two categories: "Data Review" reviews the previous recorded data; "Function Setting" allows you to change various settings. Note: In the Menu Screen, battery runs down faster than the normal measuring screen.
Menu screen (Data review) Data review Checks and reviews the accumulated data of the past. Press MENU button again to return to measuring screen. Note: The data of weeklky distance, monthly distance and yearly distance are the accumulated amount of the trip distance (Dst). This accumulated amount is saved when the clock passes midnight. When saved, the digits after the second decimal place are cut off. Therefore, the accumulated amount differs from the data of odometer (Odo).
Menu screen (Function settings) Function setting The function setting screens allow you to change various programmed functions. Current settings for each parameter are displayed on the appropriate function setting screen (except for display contrast and personal data). Pressing ENTER/START/STOP button on a function setting screen brings up the setting change screen.
Menu screen (Function settings) Date setting ENTER (START/STOP) Function setting screen Sets the date. First set the year, then the month, then the day. It is important to follow this procedure correctly, as previously stored data may be affected. Select a number using SELECT/MODE button, and press ENTER/START/STOP button to save it. After the day has been set, the verification screen will appear. Press ENTER/START/STOP button to save the setting.
Menu screen (Function settings) Display contrast setting ENTER (START/STOP) Function setting screen Adjusts the contrast of the screen (right: darker, left: lighter). Move the scale mark using SELECT/MODE button, and press ENTER/START/STOP button to save the new "contrast settings". Note: The darker the display, the higher the battery consumption. Personal distance ENTER (START/STOP) Function setting screen You can input accumulated distance from a different cyclocomputer.
Menu screen (Function settings) Personal data input ENTER (START/STOP) Function setting screen You can enter your name and birthday. Name and birthday can be entered separetely. Select NAME or BIRTHDAY using SELECT/MODE button. How to enter personal data Select NAME or BIRTHDAY using SELECT/MODE button. Entering your name: Up to 16 letters can be entered. 1) Pressing SELECT/MODE button repeartedly runs through the characters A-Z, a-z, 0-9, punctuation marks, space, and .
Menu screen (Function settings) Countdown setting ENTER (START/STOP) Function setting screen Turns the countdown function on and off, and specifies whether distance or time is to be counted down. How to set countdown ON/OFF ....... Turns the countdown function on or off. 1) Press SELECT/MODE button to select "ON" or "OFF". 2) Press ENTER/START/STOP button to execute your choice. SELECT ...... Selects whether the distance or time figure is to be displayed. SETTING .....
Menu screen (Function settings) Clock time setting ENTER (START/STOP) Function setting screen Auto mode Sets the clock time. Make your selection using SELECT/MODE button, and press ENTER/START/STOP button to save it. When you have selected 12h mode, take note of the AM/PM icon. Note: When setting the minute, press ENTER/ START/STOP button according to the time tone so that an accurate time setting can be carried out.
Troubleshooting If a malfunction occurs, check the following items before contacting a dealer for service. Trouble Check items Remedy The FORMAT YES/NO prompt does not appear. Are the two MODE buttons held down firmly? Ensure to hold down the two MODE/SELECT button for two more seconds after pressing and releasing RESTART button. The liquid crystal screen appears dark or there are some dark spots.
Specifications CAT EYE OS1.1 Display functions Current Speed 0.0(3.0) - 65.9 mph [0.0(4.0) - 105.9 km/h] Elapsed Time 0:00’00” - 9:59’59” Trip Distance 0.00 - 99999.99 mile [km] Average Speed 0.0 - 65.9 mph [0.0 - 105.9 km/h] Maximum Speed 0.0(3.0) - 65.9 mph [0.0(4.0) - 105.9 km/h] Total Distance 0.0 - 999999.9 mile [km] Clock Time 0:00 - 23:59 [AM12:00 - PM11:59] Countdown Tm: 9.59.59 - 59.59, Dst: 999.9 - 999.9 km Pace Arrow Indicates if the current speed is higher or lower than the average speed.
Optional parts 34 12 5 6 7 1 Bracket sensor kit [169-9650] 2 Bracket sensor kit (Long) [169-9651] 3 Speed sensor kit [169-9670] 4 Speed sensor kit (Long) [169-9671] 5 Bracket [169-9660] 6 Magnet [169-9690] 7 Screw set [169-9680] 8 Lithium battery [166-5150] 8 Limited Warranty 2-Year Warranty for Main Unit Only (Accessories/Attachments and Battery Consumption excluded) If the computer main unit is operating defectively from normal use, the part of the main unit will be repaired or replaced free of charg
REGISTRATION CAT EYE Web Site (http://www.cateye.com) For warranty service you must register your product. Please register your OS1.1 as soon as possible. CAT EYE provides as much technical support as possible by telephone, e-mail and our web site. Please register on-line through our web site, or send the registration card below directly to our Customer Service Department. For registration, please fill in the product's serial number (the 7digits number marked on the back of the main unit). CO.,LTD.
