Assembly Instructions Model 1476 French Country WorkCenter A. Assembly uses the Bastion System; a simple yet rugged compression fastening system. B. This unit is made of solid North American hardwood and has a factory applied oil finish. See the enclosed booklet for care instructions. C. Directions (left/right, front/back) are given as facing the front of an assembled unit.
MODEL 1476 PARTS LIST P/N: SLS1476 (2) Slated Shelf 31-3/4” x 20-3/4” x 1-3/4” P/N: TT1476 (1) Table Top 36” x 24” x 2-1/2” P/N: DF1476 (1) Drawer Front 27-15/16” x 4-3/8” x 3/4” P/N: FL/BRleg1476 (2) Front Left/Back Right Legs 30” x 2-1/2” x 2-1/2” P/N: DBK1476 (1) Drawer Back 27-1/8” x 3-1/2” x 3/4” P/N: FR/BLleg1476 (2) Front Right/Back Left Legs 30” x 2-1/2” x 2-1/2” P/N: DSL1476 (1) Drawer Side Left 18” x 3-1/2” x 3/4” P/N: DSR1476 (1) Drawer Side Right 18” x 3-1/2” x 3/4” P/N: TBK1476 (1) Top
HARDWARE 1476 P/N: Pin 3/4” 3/4” Long 3/16” DIA.
TIPS ON HOW THE BASTION FASTENING SYSTEM WORKS 1. The Bastion fastening system consists of a steel post (threaded on one end with a hole through the shaft on the other end); a Barrel Nut (cylindrical barrel-shaped with threaded open end & holes through the sides); and a Set Screw (Phillips slot on one end, pointed on the other) 2. To attach Posts: A) Dip threads of Post in vegetable oil.
STEP 1 Table top “L” Bracket holes Assemble Side Panels 3/4” Pin not used A. Each side panel consists of two (2) legs, one (1) top side brace and one (1) glide support brace. When assembled, diagonal legs will be the same (i.e. Front Right/Back Left & Front Left/Back Right). Side panels are identical when assembled – the drawer glides will determine left and right sides. holes for nut access holes TOP SIDE BRACE Bastion Post shelves B. Tap a 3/4” pin in each end of the top side braces.
STEP 2 Attach Drawer Glides to Glide Support Sticks A. Take the drawer glides, extend them to their fullest. See illustration 4. The glide has 3 parts. Remove the furthest extended part (1) (smallest) by pushing the black plastic lever down – then pull part out, separating it. This part will attach to the drawer side later. Attach the largest parts (2&3) to the glide support stick using holes as illustrated. Attach with Two (2) 7/16” #6 panhead screws. About 1” of the glide will overlap the front leg.
STEP 3 Attach Back Brace A. You may find it easiest to attach the back brace and shelves by inverting the island. Attach the back brace with bastions to the right and left side assembly. STEP 4 Attach Shelves A. Decide which of the 3 height choices you want the middle shelf. B. It is recommended to get a friend to help hold the shelves in place as you attach them using 1-1/4” #8 screws.
STEP 5 Table Top Preparation & Attaching Attach four (4) “L” brackets to the bottom side of the table top utilizing the inside set of holes using 5/8” #6 screws. Note the proper position of the “L” brackets. STEP 6 Attach Table Top Utilizing the “L” brackets, attach the table top with 5/8” #6 screws. Illustration 7-A Make sure the round hole is used to attach the L-Bracket to the bottom of the Table Top.
STEP 7 Insert Castors Lightly tap the castor holders into place. Do not pound flat, as the castor will not fit into place. Slide the castor into place tapping lightly with a hammer to guarantee proper insertion.
STEP 8 Assemble Drawer A. Attach the Drawer Back to the Left and Right Drawer Sides with four 1 ¼”#8 Screws. Make sure the slots that run the length of the Sides are aligned with the slot in the Drawer Back to accept the Drawer Bottom. A B. Slide in Drawer Bottom, best side up. C. Take two (2) Bastion Posts, align the threaded ends of the Posts with the post holes located near the ends of the inside Drawer Front. Tighten Posts down until the solid shaft of the Post hits the wood.
STEP 9 Insert Drawer A. Slide the drawer all the way in until you hear an audible click. The drawer should now be secured to the glides. Don’t be afraid to give the drawer a shove in to seat the glides. Note: Before inserting the drawer glides into the cabinet glides, pull out the movable sections of the cabinet glides as far as possible, then insert the drawer glides into the ends of the extended cabinet glides and slowly close the drawer keeping both sides even. Right side tab down.
Optional Pot Rack Accessory Visit us online at www.catskillcraftsmen.com to purchase the optional pot rack. Click on Wooden Kitchen Accessories in the menu on the left hand side and locate the pot rack on the accessories page. • Includes “S” hooks for hanging storage. • Features a stainless steel bar • Solid hardwood construction. • Ready to assemble • Made in the USA. The perfect addition to your new work center. Limited quantity available. Installation Instructions: Fits easily.
For continued beauty and long life of your Catskill Craftsmen cart, we recommend Catskill Craftsmen’s Butcher Block Oil. Our Butcher Block Oil is available directly from Catskill Craftsmen’s factory. For one eight ounce (8 fl. oz.) bottle, which is sufficient for two applications, simply send $6.95 along with the completed coupon to the address below. Visit us online at www.catskillcraftsmen.com to browse our assortment of butcher block care products. Visa and Mastercard are accepted online.
