Owner's manual

ManualsBrandsCatskill Craftsmen ManualsFurniture1575

CRAFTSMEN, INC.

Assembly Instructions

Model 1575

Wide Cuisine Cart

GENERAL:

1. You have purchased model 1575. Overall dimensions of an assembled unit is 32” x 17 x 34.5”

2. Should you need assistance or need to replace a damaged or missing part, DO NOT

RETURN THE UNIT TO THE STORE where you purchased it, simply give us a call at

607-652-7321 from 7:30 - 4:00 PM Eastern time and we’ll send you the prepaid part via UPS

usually that same day! Please have model number and part description ready when you call.

3. Read the assembly instructions and the enclosed brochure before beginning assembly.

Assembly is very easy if you read and follow the instructions step by step.

4. Tools required: Phillips screwdrivers, medium and small; medium flat blade screwdriver and

hammer.

Summary of content (13 pages)

PAGE 1
C R A F T S M E N, I N C. Assembly Instructions Model 1575 Wide Cuisine Cart GENERAL: 1. You have purchased model 1575. Overall dimensions of an assembled unit is 32” x 17 x 34.5” 2.
PAGE 2
CABINET PARTS TOP TOP P1 P2 TOP S P3 Shelf (2) Back Panel (1) Handle Side Panel (1) Plain Side Panel (1) D1 Drawer Front (1) T1 D2 Drawer Back (1) Cabinet Top(1) T2 Table Top Stick (2) Drawer Dowel (1) D7 D4 D3 Drawer Side Left (1) Drawer Side Right (1) D6 Door Spacer (1) D5 D8 D9 Left Door (1) Right Door (1) B2 Top/Bottom Brace (2) B1 Drawer Bottom (1) Middle Brace (1)
PAGE 3
CABINET HARDWARE 1 3/4” Phillips Flat Head Machine Screw (10) Towel Bar Post (2) 1 1/4” Phillips Flat Head #8 Screw (14) 1” Truss Head Machine Screw (6) 3/16” Flat Washer (4) Cam (2) 10-24 Hex Nut (10) 5/8 Wooden Disk (12) 5/8” Phillips Flat Head #8 Screw (2) 1 1/2” Long 3/16” DIA. Steel Pin (4) 1” Long 3/16” DIA. Steel Pin (8) 3/4” Long 3/16” DIA.
PAGE 4
STEP 1 1 1/4” #8 Screw 1” Steel Pin T2 P2 Repeat to other Side Panel T2 P1 STEP 2 Handle can go on either side of cart so choose which side you want the towel bar Towel Bar Post 1 1/4” Screw Washer Towel Bar P1 P2 P3 Nut 1 3/4” Machine Screw
PAGE 5
STEP 3 P3 P1 P2 1 1/4” Screw T1
PAGE 6
STEP 4 D2 A. Attach the drawer back to the drawer sides with four 1 1/4” #8 screws. Make sure parts are aligned as in illustration 4A. B. Insert drawer bottom into the slots in the drawer sides, best side to inside of drawer. Slide down until seated in the slot in the drawer back. See illustration4B. C. Screw the cam posts into the two outside holes on the inside face of the drawer front until seated. Only 3/8” of this post goes into the wood, leaving the 4 guide rings/head exposed. See illustration 4C. D.
PAGE 7
STEP 5 D7 D1 Place drawer in position STEP 6 1/2” #4 Screw 1 1/2” Pin 5/8” #8 Screw Magnet Plate 1” Machine Screw D6 D9 D8 Handel Door assembly
PAGE 8
STEP 6 B2 B2 B1 3/4” Pin Install 3/4” pins in brace ends STEP 7 B1 Nut B2 1 3/4” Machine Screw
PAGE 9
STEP 7 B2 Washer D9 D8 B1 B2
PAGE 10
STEP 8
PAGE 11
STEP 9 S S
PAGE 12
STEP 10 5/8” Wooden disk A. Stick magnet to magnet plate on right door. B. With left door open, close the right door. The magnet should be positioned over the wooden block on the bottom of the top front brace. Hold the magnet in place with your thumb, and open the right door. The magnet will be in the correct position on the block. C. Secure magnet with the two round head screws in the magnet packet. Center screws in the slots in the magnet . This will allow adjustment later, if needed.
PAGE 13
013108 For continued beauty and long life of your Catskill Craftsmen cart, we recommend Catskill Craftsmen’s Butcher Block Oil. If you would like to purchase Butcher Block Oil directly from Catskill Craftsmen’s factory, we offer a reduced price. For one eight ounce (8 fl. oz.) bottle, which is sufficient for two applications, simply send $5.95 along with the completed coupon to the address below. C R A F T S M E N, I N C.