Instructions / Assembly

ManualsBrandsCatskill Craftsmen ManualsKitchen Appliance30 in. Kitchen Island

Assembly Instructions

Model 53017

Designer Island with Flat Panel Doors

GENERAL:

1. You have purchased model 53017.

2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at

607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same

day! You may also email us info@catskillcraftsmen.com.

3. Read the assembly instructions and the enclosed brochure before beginning assembly. Assembly is

easy if you read and follow the instructions step by step. See our website for assembly tips and videos.

4. The only tools needed are a hammer, a small and a medium Phillips head screwdriver and a medium at

blade screwdriver. A pencil is also needed. A power screwdriver will speed assembly, but is not required.

Place a few drops of vegetable oil on the threads of wood screws before screwing into the solid hardwood

parts.

5. Glides are sometimes pre-packed with screws. These are not used.

Summary of content (11 pages)

PAGE 1
Assembly Instructions Model 53017 Designer Island with Flat Panel Doors GENERAL: 1. You have purchased model 53017. 2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at 607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same day! You may also email us info@catskillcraftsmen.com. 3. Read the assembly instructions and the enclosed brochure before beginning assembly.
PAGE 2
CABINET PARTS 53017 TOP TOP Outside holes not used.
PAGE 3
CABINET HARDWARE 53017 1 3/4” Phillips Flat Head Bolts (8) Handles (4) 1 1/4” Phillips Flat Head #8 Screw (12) Drawer (Used to attach drawer Front) Cam Posts (2) (Used to attach drawer handles) Cabinet Cam (2) 7/8” Truss Head Machine Screw (8) 14” Drawer Glide (1 Set ) (Used to attach cabinet glides & “L” brackets) 5/8” Phillips Flat Head #7 Screw (12) (used to attach drawer glides) 5/8” Phillips Head #5 Screw (4) 3/16” Flat Washer (2) 10-24 Hex Nut (8) (Brace Pins) 3/4” Long 3/16” Dia.
PAGE 4
STEP 1 Glide Support Assembly The “L” brackets are attached to the Glide Support using the large slot in the “L” bracket. The Hole will be used to attach the table top.
PAGE 5
STEP 2 A. Lay back panel flat on a smooth surface with holes up. B. Attach side panels with 1 3/4” machine screws (bolts) and hex nuts. After inserting bolts(s) thru the holes in the side panels, thru the holes in the long edges of the back panel, place a hex nut on the tip of your finger, align nut with bolt and tighten. C. Look ahead to step 3 which shows side panels 4 Used attached to back panel.
PAGE 6
STEP 4 A. Attach the drawer back to the drawer sides with four 1 1/4” #8 screws. Make sure parts are aligned as in illustration 4A. B. Insert drawer bottom into the slots in the drawer sides, best side to inside of drawer. Slide down until seated in the slot in the drawer back. See illustration 4B. C. Screw the cam posts into the two outside holes on the inside face of the drawer front until seated. Only 3/8” of the post goes into the wood, leaving the 4 larger guide rings/head exposed.
PAGE 7
Top Front Brace 3/4” Pin Insert Bottom Front Brace STEP 5 Take the 2 front braces and tap/insert one 3/4” steel pin into each end of both braces until seated. About 3/8” will stick out when seated. Ok if loose. 4 used in this step 3/4” Long 3/16” DIA. Steel Pin B. Insert two 3/4” pins in bottom brace as shown. STEP 6 A.
PAGE 8
STEP 7 A. Tap/insert ONE 1 1/2” pin into each end of both doors. DON’T OVERDRIVE PINS! Pins should stick up about 1/2” when seated. B. Attach the magnet plates (may be stuck to magnet!) with the 1/2” #4 screw to the top of both doors. Bumps go toward the wood. C. Attach door handles with 7/8” truss head machine screws. 4 used in this step 1 1/2” Long 3/16” DIA.
PAGE 9
STEP 8 A. Install doors by inserting pins in the door tops into the holes in the long edge top front brace. B. Place one washer on each of the door pins in the door bottoms. C. Take the bottom front brace, align pins in door bottoms with holes along top long edge of brace (are washers on pins?) and secure brace with 1 3/4” bolts/hex nuts as before.
PAGE 10
STEP 10 A. Insert and tap caster sockets with hammer until the teeth grab the wood. DON’T POUND SOCKET FLAT OR CASTER SHAFT WILL NOT ENTER. B. Insert casters and seat by pushing straight downward with heel or your hand, or tap into place with a hammer. Don’t be afraid to give them a good downward whack on the solid metal part of the caster! C. Locking wheels usually go on back, but can go diagonally or on the front if cart is moved a lot. STEP 11 A. Upright unit.
PAGE 11
For continued beauty and long life of your Catskill Craftsmen cart, we recommend Catskill Craftsmen’s Butcher Block Oil. Our Butcher Block Oil is available directly from Catskill Craftsmen’s factory. For one eight ounce (8 fl. oz.) bottle, which is sufficient for two applications, simply send $6.95 along with the completed coupon to the address below. Visit us online at www.catskillcraftsmen.com to browse our assortment of butcher block care products. Visa and Mastercard are accepted online.