Installation Sheet

EMERGENCY RELEASE
BUTTON (OPTION A)
7.62mm
(5/16”)
SQUARE
SPINDLE
LOCKING
BUTTON
SPRING
LOCKING PIN
(OPTION B)
CENTRE LINE
HEIGHT LINE
CARDBOARD
TEMPLATE
TOP HOLE
CENTRE
FIXING
SCREWS
CLOSING JAMB
HEIGHT LINE
DOOR
HEIGHT LINE
TRANSFERRED TO
CLOSING JAMB
STRIKER
FITTING INSTRUCTIONS
for the CL100 Mortice Case
Please read
instructions carefully
before starting
(LaviLock Only) Fit either:
Option A: Locking button inside,
emergency release button outside.
Option B: Locking buttons inside and
outside.
Do not forget to put the 4mm (5/32”)
diameter spring(s) into the locking
button(s).
Note: Option A is the normal
configuration, however Option B can be
used where “Quick Emergency” access
is required to a room, e.g. a toilet in a
resthome.
D: Place the indicator plates one each side of
the door, over the buttons as shown (the
unlock / lock indicator plate goes to the
inside of the room).
E: While holding the indicator plates in place,
slide the 7.62mm (5/16”) square spindles into
the lock.
Fit the chosen lever handles (you may need
to cut the spindle and screws to length first).
Check that the handing of the handles is
the correct way around and only tighten
the screws enough to hold the handles and
indicator plates onto the door.
F: Test the lock for the following:
a) That the handles move freely.
b) That the latch returns to the latched
position once the handles are let go.
c) That the locking button(s) move up and
down freely without jamming.
d) That the indicator plates are parallel
with the edge of the door.
G: When the testing is complete, fully tighten
the screws holding the lever handles, and
follow instructions for ‘LaviLock’ under
‘Hole Drilling Options’ on back of Template.
H: Slide the door closed and transfer the height
line from the door onto the closing jamb.
Cut out the Template where marked and
align the top of it with the height line.
Mark the top screw hole, making sure that it
is in the centre of the closing jamb (use the
centre line that is marked on the Template).
Fit the striker using the top screw only.
Close the door slowly to check that the
striker lines up with the lock, adjust if
necessary then fit the bottom screw.
On timber jambs you may mortice the back
of the striker into the closing jamb to a
depth of 3mm (1/8”) (Diagram E).
STAGE 3:
Fitting Lock (Lever or Flushturn)
A: Fit the lock into the mortice and screw in
place using the #10 countersunk screws
supplied.
B: Slide the 7.62mm (5/16”) square spindle
into the lock (if required) and fit the chosen
handles (you may need to cut the spindle
and screws to length first).
C: Slide the Europrofile cylinder (if required)
into the hole until the tapped hole in the
cylinder lines up with the corresponding
hole in the lock case.
Fix the cylinder into place with the cap
screw supplied (access to the hole is
through the long slot in the inner forend).
Tighten the cap screw firmly and then fit
faceplate to forend.
D: Test the lock for the following:
a) That the handles move freely.
b) That the latch returns to the latched
position once the handles are let go.
E: Fit the escutcheons around the cylinder.
F: Slide the door closed and transfer the height
line from the door onto the closing jamb.
Cut out the template where marked and
align the top of it with the height line.
Ensure the striker is facing
right way up with the
slotted screw hole to the
top (Diagram F).
Mark the top screw hole,
making sure that it is in
the centre of the closing
jamb (use the centre line
that is marked on the
Template).
Fit the striker using the top screw only, close
the door slowly to check that the striker lines
up with the lock, adjust if necessary then fit
the bottom screw.
On timber jambs you may mortice the back
of the striker into the closing jamb to a
depth of 3mm (1/8”).
© All copyright and other property in this document is reserved by Cavity
Sliders Limited. Details and specifications are subject to change without
notice. Whilst all care is taken to ensure the accuracy of all information, no
responsibility will be accepted for any errors or omissions.
® CS FOR DOORS and CAVILOCK are Registered Trademarks.
New Zealand Patent No: 533838.
CS CAVILOCK® (O.D. 1994). 03.2016 / CL100ZA520
D E