Installation Sheet

All copyright and other property in this document is reserved by Cavity Sliders Ltd.
Details and specifications are subject to change without notice. Whilst all care is taken to
ensure the accuracy of all information, no responsibility will be accepted for any errors or
omissions. *Guarantee conditions apply. Contact Cavity Sliders Ltd for details.
1/7-11 Rodborough Rd
Allambie Heights
NSW 2100
cavitysliders.com.au
548 Finney Ct,
Gardena, 90248 CA
USA
cavitysliders.com
5 - 7 Rakino Way
Mt Wellington
Auckland 1060
csfordoors.co.nz
Installation Instructions
4
PAGE
Install Activator into Door
20.
If door is installed, remove it from the track.
Mark a centre line on the top edge of the door.
1
2
1
2
12.5mm
(1/2”)
Ø20mm (13/16”) to
depth of 40mm (1-9/16”)
Ø3mm (1/8”)
to depth of
40mm (1-9/16”)
Ø3mm (1/8”)
Rivnut
plates
Sofstop
dampener
Slide
cassette
down the
track
Rivnut
plate
Sofstop
cassette
Activator head
flush with bolt
Activator
Mark on
activator
head
Claws
Lifting
tool
Nut
Activator
head
Spanner
Lifting
tool
18.5mm
(47/64”)
18.5mm
(47/64”)
c
L
21. Check activator head
is flush with the bolt.
This is necessary in
order to reconnect the
door to the track.
Screw activator to top
of door using supplied
screws.
Position SofStop cassette:
Install door on the track then follow Option A or B.
Note: Cassette can be installed charged or uncharged.
4
23. Align rivnut plates
of the assembled
SofStop cassette
with the groove on
the underside of the
track. Check SofStop
dampener is in the
correct orientation
and slide the cassette
down the track.
Go to step 25.
Front face of door
Centre line
Top of door
Top of door
Check SofStop dampener is in the correct
orientation and slide the cassette down the track.
Align cassette with the first rivnut plate and loosely
screw plate to the cassette.
Align Unit and Test.
25.
Move door into closed position.
29. Test SofStop works by opening and closing the
door. Check that the unit won’t slide out of position
if the door is closed faster than usual.
Adjust or tighten if necessary.
30. For units requiring Soft Open and Soft Close,
repeat steps above to install a SofStop cassette
at the other end of the track. Only one activator is
required on the door.
NOTE:
• If the unit doesn’t activate, the activator head is not
tall enough. Repeat Steps 26 - 27 to adjust.
• If the door does not close to the desired position
repeat Step 25.
Option B: Limited space on end of track.
24. If there is limited
space, slide one rivnut
plate into grooved slot
on underside of track.
Attach second rivnut
plate loosely on the
opposite end of the
cassette.
20
25
26
27
21
23
24
Slide SofStop cassette
to align activator head
with the unit claws.
Open door and tighten
screws on rivnut
plates to lock SofStop
in position.
Close door and check
alignment. Loosen
rivnut plates to adjust
position if required,
then re-tighten.
26. With the door closed,
use the lifting tool to
pick up the activator
nut then slide the tool
under the nut.
27. Using the supplied
spanner raise the
activator head to its
marked position by
tightening the nut.
NOTE: Check that
activator head is high
enough to interact
with the claws of the
SofStop unit.
Keep tightening
if head is not tall
enough.
28. Pull lifting tool out
to drop nut back into
seated position.
View from back of track
Option A:
Open track ends method.
22. Loosely connect the
rivnut plates to the
SofStop cassette
using the supplied
washers and M5
socket head screws.
Rivnut
plate
Continue with track installation (Step 15, Page 3)
22
Mark and drill holes
as shown: