4 / 8 / 16 Channel Stand-Alone DIGITAL VIDEO RECORDER DR-Series DVR USER’S MANUAL
• INDEX • CHAPTER 1. Specifications & System Organization 1. Specifications ------------------------------------------------------------ 3 2. Product Contents List -------------------------------------------------------- 5 3. System Organization --------------------------------------------------------- 6 • CHAPTER 2. Product Description 1. Front Panel(8&16CH) -------------------------------------------------------- 7 2. Rear Panel(8&16CH) --------------------------------------------------------- 8 3.
• INDEX • CHAPTER 5. MENU ⊙ Go to Menu -------------------------------------------------------------- 17 ⊙ Go to System Setup -------------------------------------------------------- 17 1. Display ------------------------------------------------------------------ 18 2. Camera ----------------------------------------------------------------- 21 3. Sound ----------------------------------------------------------------- 24 4.
1. Specifications & Organization 1. Specifications Video standard PAL/NTSC Audio 2-way Audio conference Monitor display Real time:25 Fps (PAL), 30Fps(NTSC) per camera Covert camera operation Programmable Event/Log search Up to 1,000,000 for user login/out, config changes, remote access, connects/disconnects Record Scheduling Daily, Weekly adjust specific Hr per channel Remote Access TCP/IP, View, Search, Recording & Control by Client Program or I.E.
1. Specifications & Organization Pre-alarm recording Up to 5 sec.
1. Specifications & Organization 2. Product Contents List Please confirm that all product contents are present after opening the package. ① Basic Contents DR8N or DR16N Unit AC Power Cable 8 / 16 Channel Stand-Alone DIGITAL VIDEO RECORDER DR-Series DVR USER’S MANUAL Revision Date : 09.20.2006 Firmware Version : 5.7.6.
1. Specifications & Organization 3.
2. Product Description 1.
2. Product Description 2. Rear Panel(8&16CH) 4 1 5 2 6 7 3 11 8 9 10 12 ① Video IN / Loop : BNC Video Input Port (1 ~ 8/16), BNC Video Loop Output (1 ~ 8/16) ② Monitor out : BNC Main Monitor Output SVHS : Output Video by Connected SVHS.
2. Product Description 3. Front Panel(4CH) 14 1 7 2 15 3 8 9 10 1 CD-RW : CD-RW Device for Backup. 2 Channel Selection Button : Select Channel or Input Password. 3 Led Indicator : Indicate Present System Status Information. ( PWR: System On/Off, REC: Record On/Off, 4 11 12 5 13 ALARM: Alarm Sensor Detection Status, NET: Client Network Connection Status, ) 4 Search Controller : Searching Recorded Data or Control Menu & PTZ/FOCUS. 5 HOLD : Hold Jog dial.
2. Product Description 4. Rear Panel(4CH) 1 3 2 4 6 5 7 11 8 9 10 12 1 Video In : BNC Port for Connection of DVR & Camera. (4 Camera Connectable) 2 Loop Back : Output DVR Camera Video to Loop Back Port. (4 BNC Port) 3 Monitor Out : Output DVR Video to AV Monitor. 4 Spot Out : Output Spot-out Video to AV Monitor. 5 NTSC/PAL : Select NTSC or PAL Type. 6 VGA OUT : Output Video to a Computer Monitor by Connected VGA (Option) 7 SVHS : Output Video by Connected SVHS.
2. Product Description 5. Remote Controller POWER MENU: Open System Setup Menu System ON/OFF Channel Selection Buttons RETURN ENTER: Apply / Select / Go to Next Screen Cancel / Deselect / Previous Screen Navigation Buttons : used for Playback Control, Menu Navigation, and PTZ/Focus Control Change Display Mode Search Menu PTZ/IRIS Control • There are buttons on the controller that are unused, and their descriptions have been omitted.
3. Display 1. System Power ON • Press Power Button to Startup the DVR. • After the Power-On Self-Test, the system will ask the user to input a password to begin operation. • Initial Display Mode is 8ch / 16ch Live View Mode. • DVR will startup with Continuous Recording enabled on all channels by default. Initial System Startup - Login Screen • Each channel indicates Camera Name and Recording Status. • Present Date/Time shown on Status Bar at bottom of screen.
3. Display When this unit is connected with a remote client PC, a Network Status Icon will appear on the Status Bar. • This icon indicates the current network conditions. - Green: Network is connected and stable. - Blue: Network is connected, but is unstable. - Red: Network is very unstable. 2. Live View Display Mode Selection • Select One Channel using the Channel Selection Buttons (1 ~ 8/16). • Use the Display button to change the multi-channel Display Mode.
3. Display 4. PTZ/FOCUS Control • Control Camera Movements of PTZ (Pan/Tilt/Zoom) Devices • Press PTZ Button to switch into PTZ mode. (Status Bar is replaced by PTZ controls) • Each PTZ function is manipulated by using a button on the Front Panel or on the Remote Controller. • Some of the notations on the PTZ menu are abbreviated. (P: Pan, T: Tilt, Z: Zoom, F: Focus, I: Iris) • All of the functions on the PTZ menu are labeled along with the Front Panel / Controller button that controls it. 5.
4. Search ⊙ Go to Search Mode • Press Search Button and Log-In as Administrator or Manager. • Use Directional Keys to Navigate Search Menu. • To Open/Advance Each Submenu, Press Enter. • To Return to a Previous Menu Screen, Press Return. (Repeatedly Pressing Return will exit out of all menus.) 1. Search by Time - Ability to Search by a Recorded Date/Time ① Move Cursor to Select the Date on the Calendar. ② Press Enter to Open Selected Date. ③ The Recording Timeline will appear.
4. Search • Video Playback Controls ① : Basic Playback Mode (Normal Speed (1x) Forward Playing) ② : Normal Speed (1x) Backward Playing ③ : Pause Playback ④ : Fast Forward (2x ~ 64x Speed) ⑤ : Fast Rewind (2x ~ 64x Speed) ⑥ (enables the JOG wheel) : Variable FF/REW Speed, same as # ④,⑤ ※ Use JOG or Press Normal Forward/Backward Button while Paused, to advance Previous/Next frame. 2.
5. Menu ⊙ Go to Menu ① Press the SETUP Button. ② Unit will ask for Login/Password Entry. ③ Input Password Using by Channel Selection Buttons. ④ After Login, Select a submenu and Press Enter. -System Setup : Edit System Setup/Configuration -Record Menu : Edit Recording Schedule/Settings - Archiving : Setup and Initiate Archive/Backup Process Tip • The initial Password for the ADMIN account is 1234.
5. Menu 1. Display - Allows Configuration of Display Properties • Live View Display options are edited within this submenu. • Navigate menus by using Directional Buttons 1-1. OSD • ENTER • RETURN Select the desired menu category and press ‘Enter’.
5. Menu 1-3. SEQUENCE • Activation : Activation On/Off • List : Sequence Title • Created By: User who programmed the sequence • Choose Add to Add a New Sequence • Input the Sequence Title • Choose Activation (On/Off) • Save and Exit • To input the Sequence Title, you can open the Virtual Keyboard by pressing the Enter button.
5. Menu * Setup sequence ① Press enter then red border line disappear. Setup mode activated. ④ Setup next mode as before. Total 16 mode can be selected. ② Select display mode among 16 mode. ③ Display mode selected, press 1set can be made by 16 mode. channel selection button as you want. Input all channel NO. ⑤ When finish setup, press return. (Save & Exit / Exit / Cancel) ⑥ By SEQ button of front panel, can see setup mode. 1-4. SPOT OUT • Channel : Select spot out channel(1~4).
5. Menu 2. Camera - Allows Setup of Camera Parameters and Options 2-1. Camera Title • Covert : Set Channel as Covert Channel (On/Off) (When a channel is set to Covert, it will be hidden from Live View and Playback, but video will still be recorded.) • Title : Setup Camera Name using the Virtual Keyboard • Use the directional buttons to move around the keyboard. • Use the ENTER button to click the keyboard. 2-2. Color Setup • Adjust the Brightness, Contrast, Color, and Tint of each channel.
5. Menu Tip ※ How to use the Virtual Keyboard • Use the directional buttons to select keys on the Virtual Keyboard • Press ENTER to press a key on the keyboard • Press the button to shift for CAPS and punctuation. 2-3. PTZ Setup • Address : Set the PTZ Camera Address (0 ~ 255) • PTZ Protocol : Select Type of PTZ Camera • Baud Rate : Setup PTZ Communication Speed (2400, 4800, 9600,19200, 38400 bps) • Click the button to setup the PTZ details.
5. Menu 2-4. Motion Detection • Adjust the Motion Sensitivity Level (1 ~10) • Move Cursor over grid using the Directional Keys. • Click AREA SETUP to define motion-sensitive area • Press ENTER, and then use the Directional Keys to select an area of targets on the grid. • Area is selected on a 16 x 16 target grid. (The entire viewing area is selected on all channels by default) • Press ENTER again to mark the selected area. area that is already marked will be unmarked.
5. Menu 3. Sound 3-1. Audio - Allows for configuration of Audio parameters and options • Live Audio : Audio Output to Audio Out Terminal (ON/OFF) (Live Audio Output is from Audio In Terminal) • Audio Monitoring Channel: Select Channel for Audio Output. 1 (1 ~ 4 Channels of Audio Input) • Network Audio TX: Allow transmission of Live Audio over Network. • Network Audio RX: Allow reception of Audio talkback from PC. 3-2.
5. Menu 4. System - Basic System Environment Setup 4-1. Date/Time ※ You should set the proper Time Zone for your geographic location before adjusting the other settings. • Date / Time: Set the Present Date and Time • Date Format : Select the style of Date Display. (Ex: YYYY/MM/DD or MM/DD/YYYY) • Time Format : Setup Time Display as either 12 Hour or 24 Hour Base. • Network Time Server: Setup an NTP Time Server, to synchronize Date/Time with other devices on the Network. • D.S.
5. Menu 4-2.
5. Menu 4-3. Mail These settings allow the DVR to send outgoing E-Mail Notifications to the list of recipients listed within the DVR. • Server: Setup the outgoing Mail Server Address • Input the server address using the Virtual Keyboard. • Port: Mail Server Port Number (default is Port 25) • Security: For a Mail Server the requires outgoing SMTP Authorization (On/Off) • User & Password: Input the username and password (if required for outgoing SMTP Authorization).
5. Menu 4-4. User Management DVR User Account Setup • There are 3 groups of User Account types: - Administrator, Manager, and User • A total of 7 users can be established for each account type. • Input the new User ID, • Input a Password, using Channel Selection Buttons (0 ~ 9). • Choose the Group which the user belongs to. • Input the E-mail Address of the new user. • Turn E-mail Notification (On/Off) • Input User ID and E-mail Address using the Virtual Keyboard.
5. Menu 4-5. System Information • S/W Version: DVR Firmware Version • H/W Version : DVR Hardware Version • Video Signal Type: NTSC or PAL • Disk Capacity: used HDD capacity / total HDD capacity • IP Address: The current IP Address of the DVR • MAC Address: Fixed Hardware (MAC) Address of the DVR • System name : Input system name by virtual keyboard. • F/W update - User can do F/W update by USB device. - Press ‘PRESS’ - Select F/W from the list.
5. Menu 4-6. Control device • System ID : Select system ID. (1~254) • Protocol : Select protocol. • Baud rate : Setup baud rate. 5. Event/Sensor 5-1. HDD Event • Drive: All HDDs are listed by IDE Channel Number. • Smart Alarm: Set Temperature Alarm (On/Off). • Check Interval: Time between Smart Alarm checks.
5. Menu 5-2. Alarm Input • Operation: Set Alarm/Sensor Connection Status (Enable/Disable) • Type : Set Alarm/Sensor as Normally Open or Normally Closed. (N/O) (N/C) 5-3. Alarm Out ※ Configure the DVR Alarm Relay Output for each channel to trigger relay output on alarm activations, video loss, or motion. • Channel : Select Channel of Alarm Output • Mode: Setup Relay in Latched or Transparent Mode. • Type: Setup Relay Type as Normally Open or Normally Closed.
5. Menu 5-4. Buzzer Out • Operation: Buzzer Out (Enable/Disable). • Mode: Setup in Latched/Transparent Mode (same as Alarm Out). • HDD Event: Turn Buzzer (On/Off) when HDD Event occurs. • Duration: Buzzer time (5 sec ~ 5 min, or manual reset on DVR) • Setup each channel to trigger Buzzer on Alarm Activation, Video Loss, and/or Motion Event.
5. Menu 5-5. E-Mail Notification • E-Mail Notification will send an e-mail to a list of recipients, based on Alarm, Video Loss, Motion, or HDD Events. • Check or uncheck each type of condition that you want to trigger an EMail Notification, on each channel. • The list of recipients is configured within the System Æ User Management menu. • Make sure that all of the outgoing mail server settings are correct, within the System Æ Mail menu, in order to ensure delivery. 6.
5. Menu ⊙ Go to Record Menu • Press the Setup button and login as an ADMINISTRATOR. • Choose “Record Menu” 1. Recording Operations • Schedule Mode: Choose ‘DAILY’ or ‘WEEKLY’. - Daily : The recording schedule that you configure will be used for every day of the week. - Weekly: You must configure the recording schedule for each day of the week, individually. • Pre-Event Recording Time : (1 ~ 5 seconds) Data will be recorded to the HDD from 1 to 5 seconds before an event is detected.
5. Menu 2. Continuous / Motion Record Schedule 2-1. Parameter • Select a block of time from the 0-24hr Timeline (you may select multiple blocks). • Press ENTER again to set up the Resolution, FPS, Quality, and Audio on each channel. 2-2. Schedule • Continuous Recording Icon • Select an area (channel / time of day) on the schedule grid and Press Enter to adjust its properties. • Motion Recording Icon • Set area as ‘Timer’ (Continuous), ‘Motion’, or None.
5. Menu 3. Alarm Recording Schedule 3-1. Parameter • Select a block of time from the 0-24hr Timeline (you may select multiple blocks). • Press ENTER again to set up the Resolution, FPS, Quality, and Audio on each channel. 3-2. Schedule • Alarm Recording Icon • Select an area (channel / time of day) on the schedule. • Press Enter to Select (or Deselect) Alarm Recording. • If ‘WEEKLY’ recording is enabled, you must set up each day of the week individually.
5. Menu 4. Panic Setup • To setup each channel, press enter. • Setup each channel. (Size, FPS, Quality, Audio) • By panic button of front panel, can record urgently as setup.
5. Menu ⊙ Go to Archiving 1. CD-R/W and USB Archiving / Backup ① Device : Choose from available media. (CD-R/W and/or USB Memory Stick are detected automatically.) ② From : Select the Start Date/Time of the video recording that you wish to archive. ③ To : Select the End Date/Time of the video recording that you wish to archive. ④ Channel & Video/Audio Selection : Select (check) the Channel, Video, & Audio to include in the archive.
6. Client • Minimum and Recommended System Requirements for a Client PC ① Main Board (CPU): Pentium III @ 500 MHz (minimum), Pentium 4 @ 1GHz or above (recommended) ② OS: Windows 2000 Pro (minimum), Windows XP Pro (recommended), DirectX version 9.
6. Client ③ Choose the Folder where the Remote Agent software will be installed. ④ The Remote Agent software files will be copied onto your PC, with a status bar showing the progress.
6. Client 1. Introduction ③ ① ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑭ ⑬ ① Main Display : Shows single or multi-channel view of cameras connected to the DVR. ② Camera Selection Buttons : Indicates Camera #; click button to display a selected camera. ③ Minimize / Exit : Minimize DVR Client Window (to taskbar) or Exit Remote Agent.
6. Client 2. Configuration 2-1.
6. Client 2-2. Add Group ① ① At ‘site’ of left upper side, right click the “Add Group”. ② ② Input the Group name.
6. Client ③ ③ Input DVR information.
6. Client ⑤ ⑤ New DVR list is shown on the left upper side.
6. Client 2-3. Configuration ① Video OSD : Select screen information. (title, name, date, time) ② Video output : Select video output method. - Overlay Mixer : Output without passing through CPU. - Video Renderer : Output through CPU. - GDI : When you cannot see video by upper 2 way, use this way. ③ Video mode - Screen switching interval : During the monitoring, select screen rotation interval time(2~300sec.) - Alarm pop-up : Pop-up time of alarm happened channel on (2~60sec.) /off.
6. Client Press button, select DVR name, and press Select. Password Input Window Open, then input password. 1. Record • Alarm Recording Schedule - Click the “Set” Button for Alarm Recording. - Setup size, rec. rate, quality, audio. • Record Operations • Continuous/Motion record Schedule - Schedule Mode: Weekly or Daily. (When weekly mode, setup each day.) - Pre Event Recording Time: When event happen, record image including setting time before event happened.
6. Client 2. Camera • Status/Title Setup - Setup for Each Camera (Covert function On/Off, Camera Name). • Color Setup - Setup Color for Each Screen. • Covert/PTZ Setup - Setup for Each Camera PTZ Protocol, Baud rate. • Motion Area - Click the “Properties” button. - Click the “Camera” Button. - Setup about PTZ camera. - Select area by mouse drag, and Choose menu (Select/Deselect/Cancel). 3. Sound • Live Audio Setup - Live Audio : On/Off. - Audio monitoring channel : Select channel.
6. Client 2-4. Event/sensor • Alarm Input - Setup for Each Channel Alarm Connection & Type. • Alarm Out - Setup each channel when alarm, videoloss, motion are happened. - Disk Event: Alarm On/Off when HDD has the problem. - Operation: Setup Relay Connect with Alarm Sensor. - Mode: Setup Reacted Relay as Latched/Transparent Mode. - Type: Setup Relay Type N/Open or N/Close. - Duration: Setup Reacted Relay Time.
6. Client 2-5. System • System Info - Possible to Watch DVR System Status. • SMTP - Setup the mail server and user’s E-mail. • Users - Setup the Users. - Click the “Add” or “Modify” button. • Disk Overwrite - Setup DVR HDD Overwrite On/Off.
6. Client 3. Monitoring 3-1. Select Remote DVR to Connect • Select I/D to Connect Server. • I/D can be Add, Change, and Delete at Setup. 3-2. Screen Division Selection • 1*1 View : Showing One (1) Video which User Selected. (Selection Video by Camera Selection Button) • 4*4 View : 4 Screen Division Mode. • 9*9 View : 9 Screen Division Mode. • 16*16 View : 16 Screen Division Mode.
6. Client • 9-Channel View Mode • 16-Channel View Mode 3-3.
6. Client 3-4. AVI Video Conversion • Click AVI Conversion Button to Begin AVI File Conversion. • During AVI Conversion, a message is displayed. • Click ‘Stop” to Stop Conversion and Save AVI File. • The path and filename of your saved AVI file is displayed. • AVI files are played within Windows Media Player or the ‘Backup Player’ program that installed with ‘Remote Agent’. • In order to play the AVI files within Windows Media Player, the user must install the IMM4 Codec. 3-5.
6. Client 4. Search 4-1.
6. Client 4-2. Search Method ① ⑥ ⑤ ② ④ ③ ⑦ ① Indicates the Time of Day (0 ~ 24 hours) on Search Timeline. ② Indicates Recording Mode (Blue : No Recording, Red: Recorded Images Present) ③ Search Bar : Drag bar with the mouse to search through recorded video on the timeline. ④ Indicates each individual channel on the timeline. ⑤ If there are 5 or more channels, you may scroll through the channels using the arrow buttons. ⑥ Adjust the volume of the audio playback (if audio is present in the recording).
6. Client 4-3. SEARCH Options ③Save Image ①Archive ⑤Log Viewer ②Backup Play ⑥Event Viewer ④Print ① Archive – Backup Image from Server to Remote PC. • Time Range - Enter the Starting and Ending Date/Time. • Channel : Check each channel to include in the Archive. • Include Audio : (check/uncheck) to include Audio in Archive. • Select All / Deselect All : Select/Deselect All Channels. • Press OK to begin the Archiving process. As each AVI file is written to the PC, the system will display status.
6. Client ② Backup Play (DVR Player) – Transfer to DVR Player ① ② ③ ④ ⑤ ① Video Display (Single-Channel Mode available only) ② Open Backup File for Viewing ③ Indicates Playback Channel ④ Indicates Present Date/Time and Searchable Dates/Times ⑤ Playback Control (Forward and Reverse Play, FF, REW, Frame Forward/Reverse, Stop, Pause, Play Speed) Tip • Backup Player can be run independently of the Remote Agent software.
6. Client ③ Save Image – Capture Image and Save to Local PC • Click ‘Save Image’ Icon during Video Playback. • Chose Filename and File Type (JPG, BMP), and Save Location, and click ‘Save’. ④ Print Image – Present Image Capture and Print Out Image • Click ‘Print Image’ during Video Playback.
6. Client ⑤ Log Viewer – Find Video from the DVR Event Log. ② ① ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ① Select Starting Date/Time and Ending Date/Time from which to search for Event Log events. - Press Search Button to Search and View Search Results. ② Choose the DVR to Search. ③ Indicates the order in which events in the Event Log occurred. ④ Indicates the Camera # on which the event occurred. ⑤ Indicates the Date/Time when the event occurred. ⑥ Description of the event. ⑦ Move to Previous Page of Search results.
6. Client ⑥ Event Viewer - Showing Present Event in Server & Find Image ① Indicates the order in which events occurred. ② Indicates the DVR # on which an event occurred. ③ Indicates the Camera # on which an event occurred. ④ The Date/Time during which the event occurred. ⑤ Description of event. ⑥ Go to Selected Event on the Search Timeline. ⑦ Return to Search Window.
6. Client 5. Web Client • WEB Client Connection ① Input the IP Address or URL of the DVR in the Internet Explorer Address Bar. ② A dialog will appear to confirm download of an ActiveX control. Please click ‘Confirm’ or ‘Continue’. ③ Web Client Window will appear in Internet Explorer. ④ All functions are the same as within the Remote Agent software.
6.
